similar to: XEN Installation

On Wed, May 25, 2011 at 12:41 AM, JAMES BOND 123 007 <james123007@gmail.com> wrote: > Hi , > I saw your thread post at > http://web.archiveorange.com/archive/v/ZvO4jnaavtTfcyqnHoRX > , about problems with XEN 4.0 installation. > I have the same problem and my machine is similar to yours( HP Proliant > DL380G6, 4GB-RAM) This question is better asked on the xen-users list.

My system is a dual Xeon E5540 (Nehalem) HP Proliant DL380G6. When switching between Xen 4.0.2-rc1-pre and Xen 4.1-unstable I noticed that the NUMA info as shown by the Xen ''u'' debug-key is different. More specifically, the CPU to node mapping is alternating for 4.0.2 and grouped sequentially for 4.1. This difference affects the allocation (wrt node/socket) of pinned VCPUs to the

Hello, I have some diagnostic Info for you. Tried to get xen-4.0.1 working on another node of my cluster. Only difference: Newer revision of the Hardware. Exactly same Software Stack. Stack: Ubuntu Lucid 64bit, xen-4.0.1 from Source, selfbuilt linux-2.6.32.27 from xen/stable-2.6.32.x Nodes working: HP DL380G5 16GB (Intel X5460) Node not working: HP DL380G6 16GB (Intel X5550) Effect: Xen

Hi, I installed Xen 4.0.1 from source on Debian 5.0.8 and when boot my computer hardware reboots at like "Scrubbing Free RAM". I tryed to find some information here but none was helpfull to me. Anyone? I have 4GB memory and a AMD Turion II X2 M500 (

I'm looking at ordering a server from HP. I checked around on Google and found in the Wiki that the ProLiant DL380 is supposed to be known to work with *. I'm going to get a price quote on the following setup: HP ProLiant DL380 G4 Server w/ the following options: Intel Xeon 3.20GHz/1MB 2GB REG PC2-3200 (2 X 1GB) HP ProLiant Battery Backed Write Cache Enabler for SA6i RAID 1 drive set HP

greetings, for those of you in the know, may i have some assistance in helping to make better decisions in purchasing more used server toys to install CentOS on please? :-) in the Compaq Proliant Rackmount DL380 line, the one that looks like the older 1850R is called a G1 meaning Generation 1 right? and then the DL380 G2 is a redesign that is gray and just has 6 drive bays up front correct?

I have CentOS 6.x installed on a "HP ProLiant DL380 G5" server. It has eight 750GB drives in a hardware RAID6 array. Its acting as a host for a number of OpenVZ containers. Seems like every time I reboot this server which is not very often it sits for hours running a disk check or something on boot. The server is located 200+ miles away so its not very convenient to look at. Is

Hello Everyone, I recently installed CentOS 5.5 x86_64 on a brand new ProLiant DL380 G7. I have identical OS software running reock-solid on two other DL380 ProLiant servers, but they are G6 models, not G7. On the G7, the installation went perfectly and the machine ran great for about 2 weeks, when it just seemed to "stop". The system stopped responding on the network, and there was

Guys, I'll be building a couple of DL360 G4p & DL380 G4 boxes soon and I've not dealt extensively (i.e. at all) with any PC stuff that hasn't been i386. I know the DL line pretty well but it was all G2/3. So, question is, do I stick CentOS i386 or x86_64 on them? 2 boxes x 2GB RAM and 1 x 4GB, all SMP. Will.

> I have been running performance tests on our Debian-Samba 3 file > server. It is running the 2.4 kernel on a ProLiant DL380 G3 server > (Full Specs below). For a windows client, we are running Windows 2003 > server on the exact same hardware. They are both running at Gigabit > speed. > > What we have found is that on files 16MB and smaller we can get better >

Hello, Has anyone out there been able to qualify the Proliant DL360 G7 for your Solaris/OI/Nexenta environments? Any pros/cons/gotchas (vs. previous generation HP servers) would be greatly appreciated. Thanks in advance! -Anh

Hi, i have a proliant dl380 g5, with an amd as1000. I try to install centos8 with gui, but when try to start the new installed system, the xserver don't start. There is a throuble with the amd es1000 driver. This grafic card, seems not supported more from amd. I need a minimalistic gui for study for rhcsa certification. The gui is mandatory for the exam. Any help? Paride

Greetings, Can anyone relate experience(s) installing CentOS on Compaq rack mount servers units please? Easy no problem, easy some issues, or ghastly do not do it under any circumstances... ;) Basically, I'm looking at some used/refurb dual PIII units and will run RAID on Compaq built in SCSI or is it easy to pop in some 3ware SATA in them? Let me know in terms of CentOS 3 and/or 4 please.

Hello, I`ve got a problem which I can`t deal with. I own 2 cards - TDM2400P and TE410P. I`ve put them into a HP Proliant DL380 G4 server, compiled the drivers according to the manual. Unfortunetly there are both cards channels are configured in zaptel.conf file the first module (in this file) sends an error. For configuration: span = 1, 1, 0, ccs, hdb3, crc4 fxsks = 21-24 bchan = 25-39,

I just installed CentRC1 on a Dell gx150 as a test. I'm running into the same problem I had with Fc3. I get a partition table error when trying to use ghost8 to create an image. I was considering putting Cent4 on a ProliantDL380, FC3 installed on that machine but wouldn't boot up, stuck on Grub. I had FC2 on the Proliant but when FC2 went to the 2.6 kernel, it hung up on the Nash prompt.

Just thought I'd pass along an error I received this weekend after upgrading two servers to 5.6. Both are HP Proliant DL380 servers running 64-bit, but one is a G6 model and one is a G7. After the upgrade and the reboot to the 2.6.18-238.9.1.el5 kernel, both servers displayed the following error at boot: "pci_mmcfg_init marking 256MB space uncacheable." Some Googling

Hi to all out there using HP DL380 G4 servers, i found a way to get the Digium TE410P with older firmware running on a HP-Compaq DL380 G4 Server! Here's the step-by-step description: 1. download the latest BIOS (in my case it was 4.04 from date: 06/02/2005) for the HP-Compaq DL380 G4 using the "Systems ROMPaq Firmware Upgrade Diskette for HP ProLiant DL480 G4 (P51) Servers" Link:

Hello List, i downloaded centos6 x86_64. With DVD-iso1 i made a booteable usb-stick (universal usb installer 1.8.5.7). When i boot my HP ProLiant DL380 G4 from the stick, the CentOS boot screen comes up and and the message "Automatic boot in xx seconds..." appears. * When i do not hit any key, the seconds are counted to zero an then it starts again at 10 seconds - again and again. *

I've been seeing some random Proliant DL380 G4 64bit crashes. Each time, on the console are messages relating tojbd2/cciss and something about a waitfor 120 seconds. Is anybody else seeing anything like this? Oddly, I can't seem to find this in the logs. I guess it can't write when this happens. -- John Hinton 877-777-1407 ext 502 http://www.ew3d.com Comprehensive Online

Hi folks, We use CentOS 5.2 (with latest errata) 64bit on DL380 G5 and trying to install psp-8.11.rhel5.x86_64.en.tar.gz. After installing dependencies (like kernel-devel, rpm-devel, etc): # ./install811.sh Saving user-defined agent thresholds... [ Done ] Checking system for required packages... [ Done ] ./hpplduioss: error while loading shared