similar to: XCP 1.0 beta Realtek 8168 nic not working

Dear All, I have an onboard Realtek RTL8111/8168B NIC. from lspci -vv : 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) It is detected, but why the speed is always 100Mbps, already change cable but still no luck. I use ethtool and from the output it seems that system know that this NIC support gigabit speed : ???????

Hello everyone: Over the past few years I have been a happy samba user, running samba on Redhat / FC platforms. Recently I upgraded hardware, and Samba hasn't been performing well at all.. which makes me sad :-( The new hardware is Asus P5B board with a dual-core intel processor. This board has an onboard Realtek RTL8111/8168B gigabit ethernet controller, which was a hassle to setup.

Hello, Just did a fresh install of xen-4.0 and using the 2.6.31.13 dom0 kernel. I have 6 linux debian guests running, and on my host console i am getting these errors rolling pretty constantly. "Attempting to checksum a non-TCP/UDP packet, dropping a protocol 1 packet" I tried doing the ethtool -K eth0 tx off and same thing on peth0, using bridged mode for network config. Any tips?

Hello, Just did a fresh install of xen-4.0 and using the 2.6.31.13 dom0 kernel. I have 6 linux debian guests running, and on my host console i am getting these errors rolling pretty constantly. "Attempting to checksum a non-TCP/UDP packet, dropping a protocol 1 packet" I tried doing the ethtool -K eth0 tx off and same thing on peth0, using bridged mode for network config. Any tips?

Hi folks on debian stable I've a default samba file sharing config. Everything works perfectly (almost...) - samba version 3.6.6 >From linux and windows clients (wired and wifi too) when I (i.e. listen musics) often (one time every 4/5 minutes) networks suddenly collapse (for less one second) and immediately goes up. So I've an interrupt of broadcast (this happens also if I use rsync

Last problem I had involved changing one character in my configuration scripts. Really easy once someone showed me what was wrong. Well I think this issue is just the same. The moment I used apt to install the Xen kernal and tools I lost internet connectivity. I have been managing because I can restore connectivity be deleting the bridge mpower@dodtsair:~$ sudo ifdown eth0

I want to check the speed like features of my Ethernet in dom0 and domUs. But in virtualized environment it gives strange output why is that so? how to check it otherwise? Non-virtualized FC11 [root@fasiha home]# ethtool eth0 Settings for eth0:     Supported ports: [ TP ]     Supported link modes:   10baseT/Half 10baseT/Full                             100baseT/Half 100baseT/Full    

I want to check the speed like features of my Ethernet in dom0 and domUs. But in virtualized environment it gives strange output why is that so? how to check it otherwise? Non-virtualized FC11 [root@fasiha home]# ethtool eth0 Settings for eth0:     Supported ports: [ TP ]     Supported link modes:   10baseT/Half 10baseT/Full                             100baseT/Half 100baseT/Full    

Dovid Bender writes: > Just guessing I would verify that the out of : iptables -L -nv > Shows no dropped packets, try disabling selinux as well as look at the > limits of the asterisk pid (cat /proc/<Asterisk PID>/limits). I know the > defualt for rhel is 1024 which was never enough for us. Thanks for the hints. Selinux is disabled, there is no outgoing firewall (anymore)

On 10/10/2016 09:31 PM, John R Pierce wrote: > > oh. Yeah, the entire "net-tools" package is deprecated. I tend to forget which of the two (ethtool or mii-tool) is in that set. # Avoid using any of these: $ rpm -ql net-tools

I've got a pair of identical CentOS 6.7 servers, with SuperMicro X8DTE-F motherboards, these have 2 each Intel 82574L ethernet ports. The eth0 ports are plugged in with 10' runs of brand new cat 5e cable to a Cisco Nexxus 9000 switch (provided by the data center). These servers keep coming up at 100baseT rather than gigE. I've swapped ports and cables with a different server,

My system is: Intel CC820 motherboard (which supports PME# wake up for wake on LAN) 3com 3C905C which also supports wake on LAN via PME# Linux 5.5 The motherboard BIOS is later than one that reports an issue with WOL and this particular network card was fixed. But when I turn off the PC (shutdown or poweroff commands or front panel button), it cannot be restarted via WOL. The network light on

CentOS 6.2......... Why do the physical interfaces report (correctly) that they're negotiated at 1000Mb/s, but when I `cat /proc/net/bonding/bond0` I get 100Mbps for the member interfaces, and when I ` mii-tool bond0` I get 10Mbps for the bond? ----------------------------------------------------------------------------------------- ethtool em1 Settings for em1: Supported ports: [

I have the xensource 3.1.0 x86_64 tarball installed over a RHEL5 clone distribution. The "ethtool" utility only returns the following information: [root@fermigrid5 etc]# ethtool eth0 Settings for eth0: Link detected: yes [root@fermigrid5 etc]# Since I have no vanilla-installed rhel5 machines with which to compare, I am not sure if I am dealing with a bug in the ethtool (whose

We have an HP DL360 server with dual on-board Tigon3 ethernet cards. We are using eth0, eth1 is unused at the moment. Sometimes when the network interface is under heavy load, for example moving large file transfers over rsync or NFS, the network interface stops working and we lose all connection to the server. The only solution at this point is to jump on the console and restart the network

I''m going to set up a PVM on xen-3.3.1 debian-amd64. I need advices about the best methods to install a fresh debian on it (i.e. how to choose the kernel for pvm) . I''ve installed xen from sources and only have one xen kernel in /boot which I''m using for dom0; should I use the same kernel for domUs? There is any problem on use vcpus=2; the other vm is an hvm running

I am attempting to build an IPv4/IPv6 router. I have put a 2nd ethernet card in a box. I have one Ethernet card attached to my network and the other to a switch with nothing else there just so the link comes up for testing. When I have the built-in Ethernet attached to my network, I get pings around 60ms. The other card, btw, does not have any IP addresses configed. When I switch the

I am trying to connect two workstations (CentOS 3&4) directly using a straight through cat 5e cable with a crossover adapter on one of the ends. Both hosts have gigabit-capable ethernet card. According to lspci host 1 has: 03:0e.0 Ethernet controller: Intel Corporation 82545EM Gigabit Ethernet Controller (Copper) (rev 01) and host 2 has: 05:00.0 Ethernet controller: Marvell Technology Group

anyone know how to force network cards talk at gig speeds when all it wants to do is establish a connection at 100mbits root at host1 [/backup/cpbackup/daily]# mii-tool eth0: negotiated 100baseTx-FD, link ok eth1: negotiated 100baseTx-FD flow-control, link ok 01:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11) Subsystem: Broadcom

Hello list I have a shutdown problem. I have a machine with gigabyte GA-G33M-DS2R motherboard. Integrated network card is Realtek 8111B. I can not wake the computer after I shutdown it from FreeBSD. It is a dualboot system - windows xp and freebsd. If I shutdown the computer from windows - later I can wake it up with magic packet. Even if i shutdown the machine on the boot menu with the power