similar to: dom0 and domU questions..

Hello, maybe I''m stupid but I find no way to have the kernel in Dom0 instead of DomU for Centos 5. Here is what I did: Regular Centos 5 Dom0 install, then creating a LVM group (vms) and install DomU with virt-install works perfectly: virt-install --p --location=http://mirrors.kernel.org/centos/5/os/i386 --file=/dev/vms/centos5_data --name=centos5 --ram=512 --nographics I get a

Hi, this is my first mail in this list. I''ve installed Xen in Debian Etch and created a virtual domU Debian Etch as well. In domU I''ve installed an Asterisk and want to use a Beronet ISDN card: ~# lspci 0a:01.0 ISDN controller: GmbH ISDN network Controller [HFC-4S] (rev 01) So I pass the iSDN card PCI to domU by adding in dom0 "/boot/grub/menu.lst": --- module

Hello, What is the best way to get the xen enabled CentOS 5.2 vmlinuz and initrd images for use as a guest domain (domU) on Ubuntu host domain (dom0). Is there a site where these are available? I am hoping that I could use the vmlinuz from the latest kernel rpm, if I go that route, how could I generate the initrd image given that my host is Ubuntu? These are for use with post install of domU,

Greetings! Trying to to run a xen3 domU on a xen4 dem0 I run into problems. The xen server ''XEN1''(dom0) is openSUSE-11.3 (kernel 2.6.34) and xen-4.0.1. With qemu I created an image ''M08.raw'' from the SUSE-9.3 (kernel 2.6.11) and XEN-3.0 installation CD''s. The XEN modules were included in the installation. In M08.raw/boot I configured grub/menu.lst:

I''ve been running any number of CentOS 4 based Xen hosts and guests using CentOS 4.4, and the Xen RPM''s from www.xensource.com, and various hand-built OS images using jailtime and my own own OS images. I like the jailtime approach: One partition for / on the DomU, /dev/sda1, built as a local file or local LVM partition One partiton for swap on the DomU, /dev/sda2,

Package: xen-hypervisor-4.0-amd64 Version: 4.0.1-1 Severity: normal Because my networking was getting rather complex I cloned my firewall/net server as domU/dom0 to offload some services to the domU. I use bridged networking with the domU virtual adaptor connected to the internal ethernet interface used to provide services (which is normally the single port of the bridge). When I attempt to

Setting CONFIG_CMDLINE_BOOL=y in .config allows to assign desired value via make menuconfig: Symbol: CMDLINE [=root=/dev/sda14 ro console=tty0]                                                       Prompt: Built-in kernel command string                                                                       Defined at

retitle Traffic forwarding issue between Xen domU/dom0 thanks This week again this bug occurred again so we are trying to create some kind of reproduce algorithm. First we've created two virtual machines named koekiemonster.bofh.hq.mendix.net and netappsim.bofh.hq.mendix.net. We've added 29 vifs to koekiemonster.bofh.hq.mendix.net. During this tests we've always had a ping

http://bderzhavets.wordpress.com/2008/10/17/install-opensuse-11-domu-at-xen-33-centos-52-dom0-via-local-http-server-all-64-bit/ --- On Sun, 9/21/08, Boris Derzhavets <bderzhavets@yahoo.com> wrote: From: Boris Derzhavets <bderzhavets@yahoo.com> Subject: Attempt to create OpenSuse 10.3 PV DomU at Xen 3.3 CentOS 5.2 Dom0 via pygrub To: xen-users@lists.xensource.com Date: Sunday,

Hey, I was looking for step by step installation for RHEL5 as dom0 and RHEL5 as domU, but could not find it.I put some instructions, hope it will save some time for somebody. If you will find some errors please fix them :) I assume that you already have rhel 5 up and running (webserver as well).I will install guest system in paravirtualized mode (mine processor does not support full

I installed Debian sarge amd64 on a Intel em64t processor machines and have been using the Xen 3.0 packages in backports.org. I can boot a 32 bit guest OS fine if I use the vmlinuz-2.6.16-1-xen-em64t-p4kernel, but when trying to use the stock vmlinuz-2.6.16-xen from their binary tarball, or building it from the source package I get the following error: xentest:/var/log# xm create debian0.cfg -c

Hello, What (where) is the best way to get the xen enabled CentOS 5.2 vmlinuz and initrd images for use as a guest domain (domU) on Ubuntu host domain (dom0). These are for use with post install of domU, which is setup using xen-create-image. Thanks _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

I want to get couple of DomUs running with Xen. I installed Xen 4.1.5 from source on a Fedora 17 Dom0. I did some reading on configuring DomUs using xl/xm and cfg files. http://www.fclose.com/b/linux/2544/setting-up-lvm-backed-xen-domu/ http://www.fclose.com/w/Setting_Up_Xen_DomU_on_Fedora:_Unmodified_Fedora_on_Top_of_Xenified_Fedora_Xen_Dom0%23Install_Fedora_12_Linux_via_Internet So basically I

Hello all, I am trying to get an Ubuntu 8.04 image running on my CentOS 5.2 Dom0 which so far has only been running CentOS 5.2 DomUs. The image I am trying to run was fetched from jailtime.org (just so I didn't have to go through building an image for myself). The configuration of the DomU is based on what the guys at jailtime.org provided and its as follows name = "redgum"

Package: xen-hypervisor-4.0-amd64 Version: 4.0.1-4 Severity: normal Xen Networking[1] works by creating a new pair of virtual ethernet interfaces (vifN.M in dom0 and ethM in domU with id N) and connecting then by an internal "crossover ethernet cable". My understanding of the "internal crossover" thing is that networking statistics should be the same no matter if you measure

Package: xen-hypervisor-4.0-amd64 Version: 4.0.1-5.2 Hi, We're seeing weird behaviour regarding network traffic between a Xen dom0 and domU. I reported this issue yesterday to the openvswitch-discuss mailing list, but it seems this could also be a (regression?) bug in the xen hypervisor or the linux kernel... (we've upgraded xen-hypervisor-4.0-amd64 4.0.1-4 -> 4.0.1-5.2 and

I am using ttylinux-xen file system image a a loopback device for the domain. I am mostly using the default configuration. I am not able to get networking on the domU. Are kernel "vmlinuz-2.6-xenU" as well as "2.6.11.12-xen0" both compiled w/o loadable module support? I guess it fails when it tries to initialize the iptables on the domU when it tries to do "modprobe".

Dear All, I now have my Dom0 working nicely running Ubuntu Jaunty. I am now trying to boot Images I had been using without problem under my previous Xen installation (Gentoo). For the Dom0 host kernel I am using the debian package linux-image-2.6.26-2-xen-686_2.6.26-15_i386.deb. The DomU kernel is one I compiled myself a while ago (sometime last year and has always worked on Gentoo and I think

Hi, I have a Xen server running OpenSuSE 10.2, with Xen version 3.0.3_11774. It''s happily hosting two DomU''s running the same OS / kernel. Now I tried to create a new DomU running a newer OS - OpenSuSE 11.1. It comes with Xen version 3.3.1_18494_03. Unfortunately for me, it doesn''t work - this is what I get: > xen1:/etc/xen/vm # xm create NEW > Using config file