similar to: How to set the vif-route netdev params?

I am using Debian 6.0 "Squeeze", I applied that patch (http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=591456) to xen-common because of lack of hotplugpath.sh. network-route netdev=eth1 now does work, but vif-route gives me this error: root at xen-dom0:~# xm create /srv/xen/profiles/ca.cfg Using config file "/srv/xen/profiles/ca.cfg". Error: Device 0 (vif) could not be

I am using Debian 6.0 "Squeeze", I applied that patch (http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=591456) to xen-common because of lack of hotplugpath.sh. network-route netdev=eth1 now does work, but vif-route gives me this error: root at xen-dom0:~# xm create /srv/xen/profiles/ca.cfg Using config file "/srv/xen/profiles/ca.cfg". Error: Device 0 (vif) could not be

I''m using Xen 4.01 and jeremy''s pvops kernel, the kernel version is 2.6.32.18. At first I want to test the performance of pci passthrough when it comes to the network card 82571EB I''m using the Jeremy''s kernel 2.6.32.18 as DomU kernel too. And I found if the interface is not connected, I mean the network card receives no packet, ( the network card

I''m using Xen 4.01 and jeremy''s pvops kernel, the kernel version is 2.6.32.18. At first I want to test the performance of pci passthrough when it comes to the network card 82571EB I''m using the Jeremy''s kernel 2.6.32.18 as DomU kernel too. And I found if the interface is not connected, I mean the network card receives no packet, ( the network card

Hi, I''m using the XEN 3.4.1-pre4 Hypervisor in Routet Mode and I''m facing some problems when I start the DomU. In detail, it means that the DomU IP-Adress will not be implemented in the Kernel routing table after starting the domU via "xm create /<path +configfle>" After making a "netstat -nr" it will not show the IPadress bound to the

Hi I have upgraded my Dom0 from lenny to sqeeze and xen to 4.0 after that there were some errors when i tried to reboot, but i could fix most of them my dom0 is running fine now, but when i try to start a guest, i get an error: darwin:/# xm create infopool.cfg Using config file "/etc/xen/infopool.cfg". Error: Device 0 (vif) could not be connected. Hotplug scripts not working. i

Hello folks, I used to work with bridging for my xen networks, but my very last hosting provider doesn''t support multiple mac address on the switch port. So I''m trying to configure some virtual servers on xen 3.2.1 using the network-route and vif-route method instead of bridge. Everything works well, on the virtual server except the network. In the VM definition file, I have :

Greetings xen gurus... I''m working with xen-3.0-testing downloaded on July 3, 2006. I have configured an hvm domain and want to use vif-route and network-route to configure the communication. The domU starts up fine. I was able to complete the installation of the OS (RHES3) and can restart the domain repeatedly. However, I cannot ping the network interface from dom0 using the

Hi everyone, I need your help. I would like to create a front-back architecture with Xen. My physical server has only one public Interface. Currently, my DOM0 is using the network-route configuration: *(network-script ''network-route netdev=eth0'') (vif-script vif-route)* My DOM1 is configured with a public IP + proxy_arp with DOM0. DOM1 can connect any address on

Hi, I seem to have an interesting issue with vif-route. This is after an update to Xen 4.2.1, switching from xm to xl. I have 10 PV domUs on the host and two FreeBSD ones. All the PV domUs are now working nicely. Since FreeBSD has always been just slightly broken as PV I chose a HVM domU for those, but with PV drivers. Those PV drivers all blew up now after the upgrade. I''m now trying

Hello all, I''m using Red Hat Enterprise Linux 5 (with RH Virtualization) and a Dell Poweredge 2950 with 10 NICs. My virtual operating systems are all RHEL4, and I''ve installed 4 instances. I''m trying to set up the virtual operating systems so that the physical NICs are allocated to certain operating systems. Using the following tutorial:

A huge thank you to mario from the ''openvswitch on Xen 4.1'' post. I was having some trouble with using openvswitch with Xen 4.1 (I''m currently migrating from 4.0.1) until I saw his post and noticed that the xl.conf needed the full path to the networking script. Made this change and all is good now. Thank you. I would like to contribute what I have for using

Hello everyone! I''m new with Xen and i''ve been dealing with the same error the last week. I''m pretty much lost, i don''t know what else to do so i ask for your help. In my case i installed Xen on a amd64 Pc, with Gentoo. I installed the following packages: xen, xen-tools and xen-sources from the gentoo repositories. I''m using 2.6.31-xen-r10 gentoo

Hello, I''ve installed on a debian squeeze server, xen 4 with one VM which run in route mode configuration with an IP failover. I wanted to create another VM which turn in nat mode, so I make that : - I let my xend-config.sxp with : (network-script ''network-route netdev=eth0'') (vif-script vif-route) because my first VM is the most important.... For the second, I

Hi *, having built Xen 4.1.0 and running my Dom0 on Slackware 13.1, I''m trying to assign different physical network interfaces to different DomU guests: vif = [ ''bridge=ethX'' ] in the DomU configuration files. My /etc/xen/scripts/network-bridge script, however, doesn''t create more than one bridge: root@cen:~# /etc/xen/scripts/network-bridge start

Hi @all, I tried to setup xen 3.3 on centos 5 Update 2. I used the following packages: http://bderzhavets.blogspot.com/2008/08/install-xen-3.html The server has 4 physical network interfaces and i want to use them all. eth0 => only for host (configured with static ip) eth1 => first vm (configured with static ip) eth2 => second vm (configured with static ip) eth3 => all other vm

Signed-off-by: Kieran Mansley <kmansley@solarflare.com> Cleanup vif_state on device removal diff -r f992a517aba5 drivers/xen/netfront/accel.c --- a/drivers/xen/netfront/accel.c Wed Oct 03 13:41:33 2007 +0100 +++ b/drivers/xen/netfront/accel.c Wed Oct 03 13:45:55 2007 +0100 @@ -500,6 +500,30 @@ EXPORT_SYMBOL_GPL(netfront_accelerator_r /* + * Remove the hooks from a single vif state.

When I start xen dom0 I get that same dhcp address for eth0 and for xen-br0, dom0 can talk to the world. If I start each of my 3 domU''s mannually, each guest gets a xen-br0 vif with a dhcp address and all 3 can talk to the outside world and each other (my "flat network"). What I want is a tiered network with the first domU acting as a firewall with 3 nics vif = [

Package: xen-hypervisor-4.1-i386 Version: 4.1.1-1 Severity: important Tags: wheezy I cannot boot a domU with networking after installing the package. root at topsail:~# xm create /etc/xen/udevtest.cfg -c root at topsail:~# Error: Device 0 (vif) could not be connected. Hotplug scripts not working. [2011-08-03 15:56:53 4411] DEBUG (DevController:139) Waiting for devices tap2. [2011-08-03

Hello, I was following the steps on creating a new bridge and attaching a physical nic to it. ******Steps mentioned in http://wiki.xensource.com/xenwiki/XenNetworking#head-d5446face7e308f577e5aee1c72cf9d156903722 ***************** if you want to use multiple bridges, you must create them yourself, either manually, or via your own startup script, or via a custom script to replace network-bridge.