similar to: XCP, debian domU and updates repository

Hello, I am trying/evaluating XCP to manage our virtualization servers. Now, I have installed it in a test server and as far as I can see, it is very similar to XenServer, but I can''t manage it with XenCenter graphical console. Is there any GUI for XCP? I could connect with OpenXenCenter, but it still isn''t mature to be useful. Or do I have to use with xe commands? --

Hello, For my xen domUs I''m using a mixture of locah physical partitions (with LVM) and iSCSI disks. For local partitions, I don''t have any problem, because LVM volumes are always the same. But for iSCSI disks, devices are assigned in the order they are connected, so I can''t be sured that device that now is /dev/sdb (for example) will always be /dev/sdb. So, is there

Hello, Is it possible to create a custom template for XCP? Or edit an existing one? I know that I could create a VM and then exported as a template, but I would prefer to create a template like "Debian Lenny 5.0" that install debian from the network but with 64bits instead of the 32bits used by the template. -- Angel L. Mateo Martínez Sección de Telemática Área de Tecnologías de

Hello, I am a system manager of a datacenter. Is this moment, we about 30-40 xen servers running 2 or 3 domUs each of them. We are now using (standalone) xen over debian lenny. We manage each xen server independently, but we are looking for a central management console. At this moment, I have the doubt about using citrix xenserver (the free edition) or XCP. I didn''t know much

Hello, I have a xen server that needs to run a domU on a different vlan than xen''s. I have configured my switch (a cisco catalyst) to tag every untagged packet to the default vlan (the one in which is dom0) and to accept tagged packets (for that domU). I have xenbr0 linked with the eth0, the default network. Then I run * vconfig add eth0 101 -> To create a virtual interface with

Hello, We are trying to deploy our new ldap servers infrastructure with virtual servers running with xen. So we have installed two debian (etch) virtual machines under different domU''s (domUs are debian etch two). We are using bridge networking in xen, with default init scripts. In our test environment, these servers are working fine. But we are having problems with these new servers

Hello, I have a Xen dom0 (Debian Etch running xen 3.0.3) running different domUs. DomUs'' disks are LVM2 volumes. Now I have increased the size of one of these LVM volumes so I have to inform to the corresponding domU that its disk has increased its size (to resize it without unmounting it). How can I do this? -- Angel L. Mateo Martínez Sección de Telemática Área de Tecnologías de la

Hello, I have detected a problem with my network interfaces in my xen servers. The problem I have is that snmp is reporting interfaces as 10Mbps, although they are connected at 1000Mbps. Nevertheless, the nic is working at 1000Mbps, because it reports traffic at more than 10Mbps. This is not a critical bug, but it is annoying, because we have scripts to monitor interfaces and create usage

Hello, Since my last update of xen, I am having problems with bridges and xen. When I want to start a bridge on the dom0 (to run a domU in a different vlan than the default) I run /etc/xen/scripts/network-bridge start netdev=eth0.302 bridge=xen-br302 antispoof=no where eth0.302 is an interface associated with my vlan 302 (it tags with this vlan identifier). The problem I have is that it

Hello, We need to use iSCSI in some of our domUs. By the moment, iSCSI is not for system filesystem, but for data filesystem. I am wondering what is the best way to use it. Is it better to configure it in dom0 and then attach the device to the domU? Or is it better to configure it directly in the domU? I am thinking that if we configure it in the dom0, then we can''t share that iscsi

Hello, I am trying to run xen-3.0 in some of my dell servers. I have tried the binary distribution of xen, but it doesn''t boot in my test system (a dell poweredge 750) because a module driver problem (I get an error message during booting saying it doesn''t load a NFS root filesystem). So I am trying to compile a custom kernel. So I have downloaded linux source 2.6.12. I am

Hello, I am trying to use Xen Enterprise (its free version). Until now I have no problem, but now I want to create a new virtual machine based in debian etch, not debian sarge (the debian version included in xen templates). So I am looking for a way to create my own template, but I haven''t found any documentation about that. Looking the files, I have found that templates are stored in

Hello, Can you check following entrys: Old: disk = [''phy:vm_volumes/root.dhcp1,sda1,w'', ''phy:vm_volumes/var.dhcp1,sda2,w'', ''phy:vm_volumes/swap.dhcp1,sda3,w''] New: disk = [''phy:/vm_volumes/root.dhcp1,sda1,w'', ''phy:/vm_volumes/var.dhcp1,sda2,w'',

Hello, I have running xen over a debian server (debian sarge). Now I would like to configure a domU with redhat (AS 4), do you now any way to install it? -- Angel L. Mateo Martínez Sección de Telemática Área de Tecnologías de la Información _o) y las Comunicaciones Aplicadas (ATICA) / \\ http://www.um.es/atica _(___V Tfo: 968367590 Fax: 968398337

Hello, I’m having difficulty to starting Ubuntu 10.04 virtual machine with XCP 0.5.0. I put 3 files (vmlinuz, initrd.gz, xm-debian.cfg) in the same place under the unpacked ISO tree but when I start the VM, the following error is returned: # xe vm-install template="Ubuntu Lucid Lynx 10.04 (32-bit)" new-name-label=Teste other-config-install-repository=nfs:10.0.0.3:

Hi, What is the real difference between client and process limit? According to documentation (http://wiki2.dovecot.org/Services#Service_limits): client_limit: Maximum number of simultaneous client connections. If set to 0, default_client_limit is used instead. process_limit: Maximum number of processes that can exist for this service. If set to 0, default_process_limit is used instead. But

Hello, I am trying to configure director as described at http://wiki2.dovecot.org/Director. I have previously tried the proxy and it worked. The problem I have is that whenever I try to connect I get the error: Jul 1 11:41:41 myotis40 dovecot: pop3-login: Error: auth: connect(director) failed: No such file or directory This is my doveconf -n: # 2.0.13: /etc/dovecot/dovecot.conf # OS:

Hi Experts, What are the best tools to use for Xen Provisioning ? I have briefly looked at Eucalyptus. Is that the best ? Can you please point me out to any other options ? thanks Madhu M _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

All, Wanted to know if it would be possible to move a vm from xenserver (www.citrix.com<http://www.citrix.com/>) to a image that would run xen open source (www.xen.org<http://www.xen.org/>). If so, how? _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Hello, I continue debugging my problems with my update to dovecot 2.x :-( I have dovecot 2.0.13 running in ubuntu 10.04 (lucid) x64. My users are in a ldap directory. The problem is that I have a lot of errors like: Aug 24 23:07:32 myotis28 dovecot: auth-worker(default): LDAP: Connection lost to LDAP server, reconnecting I have seen in the mail list a patch for 1.2