similar to: Fw: Vyatta VC5 inplace of Xen-bridging.

I have set-up xen on my Intel quad core server. Now running different experiment to measure network throughput in virtualized environment. these are some of the results: Netperf-4.5 results for inter-domain communication. Sr.No.              Client               Server               Time(sec)        Throughput(Mbps)    1                   Guest-1              Dom0                   

This is my install profile F11.install name="FC11-G1S2" memory=500 disk = [''phy:/dev/sda3,0,w'' ] vif = [ ''bridge=eth0'' ] vfb = [ ''type=vnc,vncunused=1''] kernel = "/etc/xen/vm/vmlinuz.1" ramdisk = "/etc/xen/vm/initrd.img.1" vcpus=1 on_reboot = ''restart'' on_crash = ''restart''

Fasiha Ashraf --- On Sat, 22/8/09, Fasiha Ashraf <feehapk@yahoo.co.in> wrote: From: Fasiha Ashraf <feehapk@yahoo.co.in> Subject: Re: [Xen-users] my bootlog To: "Boris Derzhavets" <bderzhavets@yahoo.com> Date: Saturday, 22 August, 2009, 11:12 AM Please check what wrong here grub.conf        title Fedora (2.6.30-rc6-tip)         root (hd0,6)         kernel

A friend of mine recommended checking out the Vyatta project. I was reviewing their website and saw endorsements of their product running on both Vmware and Xen. In fact, they have a Vmware virtual image and a beta XenServer image. However, I am running a typical Debian Lenny 64 DomU installed through the repositories. According to their installation documents, it states that the ISO can be

Hello, I am working on a project where I would like to run Vyatta with Xen (v 3.0.1 from redhat). I have had only mitigated sucess so far. Actually the real Vyatta kernel doesn''t boot inside of Xen. I am planning to get the source and apply the Xen patch to it so then I could boot right off this new Vyatta kernel/initrd being Xen compliant. Here are the steps I took after I downloaded

Hi There, I''ve installed xen 3 and xen-tools on my Debian etch server and all seems well, until I try to start a guest domain. debian:/home/xen# xm create /etc/xen/D4G3.cfg Using config file "/etc/xen/D4G3.cfg". Error: Device 2049 (vbd) could not be connected. Backend device not found. I get the error: "Error: Device 2049 (vbd) could not be connected. Backend device

Hi, I just listed lenny repository and installed tinc from there. I configured tinc interface the usual way but nothing more. It would be interesting to configure the interface from vyatta itself but I don't know how to do it. ------Messaggio originale------ Da: Rob Townley Mittente:tinc-bounces at tinc-vpn.org A:tinc at tinc-vpn.org Rispondi a:tinc at tinc-vpn.org Oggetto: tinc on Vyatta?

Hi, These are my make menuconfig screen shots. I haven''t found any xen option in v2.6.30-rc. Why is that so? this happens with most of the version. What should I do? should I just let it as it is an run the make command to build the kernel? Regards, Fasiha Ashraf See the Web''s breaking stories, chosen by people like you. Check out Yahoo! Buzz. Love Cricket?

[This email is either empty or too large to be displayed at this time]

[This email is either empty or too large to be displayed at this time]

Hi there, I am getting very low throughput (around 0.29Mbps) while running netperf benchmark for guest to guest communication on a single physical host. To analyse where the time is spent in hypervisor I wanna use profiling. Please help me choosing good profiler according to my requirments. Should it be better in my case, Xentrace, gprof, xenoprof  or Oprofile. Is it possible to use some vtune

Hi there, I am getting very low throughput (around 0.29Mbps) while running netperf benchmark for guest to guest communication on a single physical host. To analyse where the time is spent in hypervisor I wanna use profiling. Please help me choosing good profiler according to my requirments. Should it be better in my case, Xentrace, gprof, xenoprof  or Oprofile. Is it possible to use some vtune

I want to check the speed like features of my Ethernet in dom0 and domUs. But in virtualized environment it gives strange output why is that so? how to check it otherwise? Non-virtualized FC11 [root@fasiha home]# ethtool eth0 Settings for eth0:     Supported ports: [ TP ]     Supported link modes:   10baseT/Half 10baseT/Full                             100baseT/Half 100baseT/Full    

I want to check the speed like features of my Ethernet in dom0 and domUs. But in virtualized environment it gives strange output why is that so? how to check it otherwise? Non-virtualized FC11 [root@fasiha home]# ethtool eth0 Settings for eth0:     Supported ports: [ TP ]     Supported link modes:   10baseT/Half 10baseT/Full                             100baseT/Half 100baseT/Full    

Folks, Xen 3.4.2 is the latest maintenance release in the 3.4 stable branch. There are a range of bug fixes since 3.4.1, and we recommend users to upgrade. The source repository can be downloaded from: http://xenbits.xensource.com/xen-3.4-testing.hg The release is tagged ''RELEASE-3.4.2''. Alternatively source tarballs can be downloaded from:

Folks, Xen 3.4.2 is the latest maintenance release in the 3.4 stable branch. There are a range of bug fixes since 3.4.1, and we recommend users to upgrade. The source repository can be downloaded from: http://xenbits.xensource.com/xen-3.4-testing.hg The release is tagged ''RELEASE-3.4.2''. Alternatively source tarballs can be downloaded from:

I have 3.4.2 Dom0(kenel 2.6.31-rc6) on top of fedora11 xend has started [root@HPCNL-SR-2 xen]# xm list Name                                        ID   Mem VCPUs      State   Time(s) Domain-0                                     0  7607     8     r-----    232.6 But i am unable to create PV guest in anyway. my virt-manager not working if i clicked its launcher in system tools. Even while using

My lenny guests don''t ping gateway. this is where I have found some probe HPCNL-SR-3:/etc/init.d# brctl showstp eth0 eth0  bridge id              8000.001b210d6131  designated root        8000.001b210d6131  root port                 0                    path cost                  0  max age                  20.00                 bridge max age            20.00  hello time               

An HTML attachment was scrubbed... URL: <http://lists.alioth.debian.org/pipermail/nut-upsuser/attachments/20091231/c46cc3c9/attachment.htm>

hi all, When i tried to install debian as a new guest VM in paravirtualized mode on Xen the following error occurs. please help me to resolve the problem.. Unable to complete install ''<type ''exceptions.ValueError''> Invalid install location: Opening URL http://172.16.0.31:8088/debian1 failed.. Traceback (most recent call last):   File