similar to: iscsi storage and multipathing

Hi, I do have one iscsi storage with 4 GBit nics of which currently only one is configured with an ip and which is in productive use by one cent os 6.3 server. Doing some research brought me to the idea to use some nic bonding or multipathing for that storage, but multipathing I did about four or five years ago only once :) Furthormore I can't find the ultimate answer (may be there is not

I'm trying to test out an Equallogic PS5500 with a server running CentOS 4.7 I can create a volume and mount it fine using the standard iscsi-initiator-utils tools. The Equallogic box has 3 Gigabit interfaces and I would like to try to set up things so I can read/write from/to the volume using multiple NICs on the server i.e. get 200+ Mbyte/s access to the volume - I've had some

We''re currently designing a ZFS fileserver environment with iSCSI based storage (for failover, cost, ease of expansion, and so on). As part of this we would like to use multipathing for extra reliability, and I am not sure how we want to configure it. Our iSCSI backend only supports multiple sessions per target, not multiple connections per session (and my understanding is that the

We've been wrestling with this for ... rather longer than I'd care to admit. Host / initiator systems are a number of real and virtualized CentOS 5.5 boxes. Storage arrays / targets are Dell MD3220i storage arrays. CentOS is not a Dell-supported configuration, and we've had little helpful advice from Dell. There's been some amount of FUD in that Dell don't seem to know what

I've got my RAC cluster running pretty smoothly now (thanks again for all the help so far), but I only have single connections between the servers and the RAID array. The servers each have two Qlogic HBAs, and I'd like to find out if there's any reasonable way to implement multipathing. The platform is RHEL 3, and Red Hat's knowledgebase indicates that they strongly recommend

Hello, I hope to be in the right list. my question is the following. I can''t seem to get multipathing configure on XCP 1.6. In XenCenter I was able to enable "Multipath" however, in the LUN under general tab I see " multipath 1 of 1 active", the the CLI I do the following command xe --m node session it list only one session. Can someone help me please? Thanks in

Dear list, we have a relatively new Sun Storage 7310, where we connect CentOS 5.5 Servers (IBM LS21/LS41 Blades) via Brocade Switches, 4GBit FC. The Blades boot from SAN via qla2xxx, and have no harddisks at all. We want them to use multipathing from the very beginning, so /boot and / are already seen by multipathd. Problem is, that the Sun 7310 has two storage heads which run in

Hello, We''ve been using Xen on several servers with direct-attached storage for a number of years. Now we''re looking to buy more Xen servers and re-purpose two of the older ones as SANs to hold the domU filesystems, in order to achieve redundancy and live migration ability. I''m looking for comments on our proposed design. SAN 1 - existing server w/ 4 GB, 2x

Hi How can i enable this feature because: Running /opt/xensource/libexec/mpp-rdac --enable it says: No module mppUpper found for kernel 2.6.32.12-0.7.1.xs1.0.0.298.170582xen, aborting. There is no MPP modules... Terveisin/Regards, Pekka Panula, Sofor Oy - Jatkuvat palvelut _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com

Hello, I will have two servers with fc storage. storage will be connected with two links to both servers ___________ ___________ | server 1 | | server 2 | -------------- -------------- | | | | -------------------------- | storage | -------------------------- on servers i will have multipathing enabled. storage has

Hi list! I have a server with dual port Qlogic iSCSI HBA. I set up the same LUN for both ports, and boot the CentOS installer with "linux mpath". Installer detects multipathing fine, and creates mpath0 device for root disk. Installation goes fine, and the system boots up and works fine after the install from the multipath root device. After install the setup is like this: LUN 0 on

I am fairly new to ISCSI and SAN technology but having recently invested in the technology I am trying to find out exactly what can and can not be manipulated, filesystem wise, without requiring a reboot. I am using the inbuilt software ISCSI initiator and multipathing in CentOS 5.1. My steps so far. Create 10GB volume on SAN # iscsiadm -m session -R # fdisk /dev/mapper/mpath0 # kpartx -a

Hi, I have an HP MSA 2000i as SAN (iSCSI) and since I'm starting with SANs, I'm seeking for advice. We are currently using HP Proliant 380 G5 + MSA 70 (SAS, direct-attached storage) for our production servers. At first, I thought I'd be using the SAN only for non-critical operations, like temporary additional storage for disk-based backups and snapshots, so I planned on using

I''m seeing seriously degraded performance with round-robin SAS multipathing. I''m hoping you guys can help me achieve full throughput across both paths. My System Config: OpenSolaris snv_134 2 x E5520 2.4 GHz Xeon Quad-Core Processors 48 GB RAM 2 x LSI SAS 9200-8e (eight-port external 6Gb/s SATA and SAS PCIe 2.0 HBA) 1 X Mellanox 40 Gb/s dual port card PCIe 2.0 1 x JBOD:

Hi, Some body know how to attach a LUN directly to an VM? Is two node pool with storage over multipath FC tied by an Qlogic hba. I''m using lvmohba with out problems, but I want to assign it directly to VM to increase the throughput. Thanks for the advice. -- Atentamente, Julian M. Sanchez Director de Tecnologías BIDDA IT Solutions Email: julian@bidda.net IP-PBX: +57(2)3333381 Ext.

Hi, I was wondering if anyone has successfully configured two lsi/3ware 9750-4i series controllers for multipathing under CentOS 5.7 x86_64? I've tried some basic setups with both multibus and failover settings, and had repeatable filesystem corruption over a iscsi(tgtd) or nfs3 connection. Any ideas? Vahan

Having just spent a day trying to recover a deleted ext3 file for a friend, I'm wondering about this way of maintining undelete information in ext3, like is done for ext2: The last step in the deletion process would be to put back the (previously zeroed) block pointers. Since it gets logged to the journal, I _think_ that this should be safe. The worst that would happen is that, if the plug

# cat /etc/redhat-release CentOS Linux release 7.1.1503 (Core) # uname -r 3.10.0-123.20.1.el7.x86_64 Hi, We use iSCSI over a 10G Ethernet Adapter and SRP over an Infiniband adapter to provide multipathing to our storage: # lspci | grep 10-Gigabit 81:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01) 81:00.1 Ethernet controller: Intel Corporation

Hello, I am trying to find out a best practice for a specific scenario. First of all I would like to know what is the proper way to set up multipath, who should care about it the host or the guest. Right now I have a setup where I have one multipath which sets my host to boot from FC SAN. I have another multipathed LUN in the host which is essentially a dm which I attached to a guest, however

Hi, I got few servers (IBM HS20,HS21 blades, IBM xSeries 3650 & others) connected to a dual fabric san throught Qlogic HBA's (23xx, 24xx). Multipathing is done with device-mapper-multipath. On CentOS 4.x i can scan for new scsi devices without any problems, get them up with multipathing & use them without any problems. However, after i started installing CentOS 5.1 (did not