similar to: pci passthrough under xen-3.3 without VT-d

Hello, I hope that I am posting the correct list with this question. I have been trying to get VGA passthrough working on my system for some time now without success. I do not have the system with me right now, so I will not be able to provide any logs or error messages right now. I will be able to to do so in a couple of hours. I have a VT-d enabled system (Motherboard and CPU) on which I wish

Hello, I hope that I am posting the correct list with this question. I have been trying to get VGA passthrough working on my system for some time now without success. I do not have the system with me right now, so I will not be able to provide any logs or error messages right now. I will be able to to do so in a couple of hours. I have a VT-d enabled system (Motherboard and CPU) on which I wish

Hello, I have been working on VGA-passthrough in the last month. When Xen was at his version 3.5 there was a few patches to make this work for some graphic cards using the patches developed by Han Weidong and posted here (http://lists.xensource.com/archives/html/xen-devel/2009-08/msg01176.html) and the same patches posted file by file are here

Hello, I have been working on VGA-passthrough in the last month. When Xen was at his version 3.5 there was a few patches to make this work for some graphic cards using the patches developed by Han Weidong and posted here (http://lists.xensource.com/archives/html/xen-devel/2009-08/msg01176.html) and the same patches posted file by file are here

Hello, I am desperately trying to get pci-passthrough to working. I want to pass a tg3 nic to domU. when booting domU I get a lot of messages: pcifront pci-0: pciback not responding!!! in domU, "ifconfig eth... adress up" hangs for 2 minutes, finally ifconfig -a shows a correct setting with no data transmitted rx/tx The IP Adress is being assigned, but there is no data transmission

All, I would like to run the following issue past the list to confirm that my problem analysis makes sense or whether I missed something: We have a HP ML370G6 server with VT-x and VT-d enabled in the BIOS. It is equipped with two Smart Array HBAs - one connected to the HDD array (SmartArray P800) and one connected to an LTO tape drive (SmartArray P212). Both controllers use the same driver

The attached patches allow the pciback module to perform a reset whenever a PCI device is: - attached to the pciback module, as so: echo "0000:01.07.0" > /sys/bus/pci/devices/pciback/bind - detached from the pciback module, as so: echo "0000:01.07.0" > /sys/bus/pci/devices/pciback/unbind - and when the guest is done with (internally when the guest is not using

Hi, I''m using CentOS 5.5 x86_64 xen 3.43 from gitco.de and I have an Openvox A1200P voip card and am passing it thru to another centos 5.5 DomU, when I 1st start the domain driver loads and everything seems quite nice and the device works, but after a reboor of the DomU, this is shown on my Dom0 dmesg Here''s Dom0 info [root@xen ~]# dmesg Bootdata ok (command line is ro

Hi, I''m using CentOS 5.5 x86_64 xen 3.43 from gitco.de and I have an Openvox A1200P voip card and am passing it thru to another centos 5.5 DomU, when I 1st start the domain driver loads and everything seems quite nice and the device works, but after a reboor of the DomU, this is shown on my Dom0 dmesg Here''s Dom0 info [root@xen ~]# dmesg Bootdata ok (command line is ro

Hello all, I''m trying to pass my PCI device through to an HVM. I''m following the steps on the xen pci passthrough wiki. First I check my pci devices #lspci - 03:00.0 VGA compatible controller: ATI Technologies Inc Device 671d 03:00.1 Audio device: ATI Technologies Inc Device aa80 04:00.0 Display controller: ATI Technologies Inc Device 671d 04:00.1 Audio device: ATI

So yesterday I got was able to get a domU successfully using a PCI SCSI card. This morning I restarted the host server. When I try to start up the same domU I get this error: Error: pci: improper device assignment specified: pci: 0000:0e:04.0 must be co-assigned to the same guest with 0000:0e:04.0, but it is not owned by pciback. How do I make this card owned by pciback on reboot. Do I need to

testing, uname -ri 2.6.33-rc5-4-xen x86_64 rpm -qa | grep -i Xen-4 xen-4.0.0_20873_01-29.1.x86_64 cat test.cfg name = ''test'' builder = ''linux'' bootloader = ''/usr/lib/xen/boot/domUloader.py'' bootargs = ''--entry=xvda1:vmlinuz-xen,/boot/initrd-xen'' disk = [

Hi, I have successfully start my Win7 x86 domU on my x64 Xen dom0 system. Now I want to give my Win7 full access to my Nvidia card. lspci 01:00.0 VGA compatible controller: NVIDIA Corporation G86 [Quadro NVS 140M] (rev a1) and I added these to my /etc/modprobe.d/xen-pciback.conf options xen-pciback hide=(0000:01:00.0) then I ran modprobe xen-pciback nothing happens on the screen, and my

Hi! I am trying to export a PCI device (an AVM Fritzcard PCI ISDN card...) to a domU but when starting my domU I am getting this error: "pciback pci-4-0: 22 Couldn''t locate PCI device (0000:00:06.0)! perhaps already in-use?" My system is running both debian etch in dom0 and domU... Below you can find (hopefully) all important information... Sincerely, Gaubatz Patrick

Hi All, Please help me. I am now installing the XEN on my PC and trying to config the pci pass through. My motherboard is intel DQ45CB which is vtd enabled. I downloaded the latest xen4.0 source from xen.org which is the latest release. I downloaded stable-2.6.32-x dom0 kernel source from jeremy''s repository. After compiling the xen and dom0 kernel, I could play it. I could create

Hi All, Please help me. I am now installing the XEN on my PC and trying to config the pci pass through. My motherboard is intel DQ45CB which is vtd enabled. I downloaded the latest xen4.0 source from xen.org which is the latest release. I downloaded stable-2.6.32-x dom0 kernel source from jeremy''s repository. After compiling the xen and dom0 kernel, I could play it. I could create

This issue was brought up about a year and a half ago. So I''ll bring it up again and see if anything happens. I''ve got an infiniband network and am attempting to pass the infiniband card through the host and give it to the guest. I''m working with standard CentOS 5.2 on both guest and host with their provided xen (3.0.3 ish). I''ve also attempted to install the

This issue was brought up about a year and a half ago. So I''ll bring it up again and see if anything happens. I''ve got an infiniband network and am attempting to pass the infiniband card through the host and give it to the guest. I''m working with standard CentOS 5.2 on both guest and host with their provided xen (3.0.3 ish). I''ve also attempted to install the

Good morning, I need to use pciback.hide to hide a pci card because I want to pci passthrough that card to a domU. My hardware neither supports Intel-Vt-d nor AMD's IOMMU. Unfortunately this doesn't seem to work in Centos 54 anymore. I guess it doesn't work because it is not compiled into the kernel, but as a module. I got the following error in dmesg and the pci device is still

Hello, I''m attempting to run Windows XP in a domU using the PCs actual graphics card. I believe I''ve set everything up correctly, including the pciback module etc. I''ve set pciback to grab the graphics card and all the USB hosts as well: (from dmesg) pciback 0000:00:02.0: seizing device pciback 0000:00:02.1: seizing device pciback 0000:00:1a.0: seizing device pciback