similar to: Guest - slow response to keystroke.

Hi, > Can you manually do on the xen interfaces what the scripts would? How about > doing it on some other interface configured in a similar way? Toying with the vif-route script, I might have found a workaround for this issue. If I disable the ifconfig and ip route commands from vif-route script, and bring up vif interface by hand later on, everything seems to work. In other works,

With GPLPV under 2.6.30, GPLPV gets the following from the ring: ring slot n (first buffer): status (length) = 54 bytes offset = 0 flags = NETRXF_extra_info (possibly csum too but not relevant) ring slot n + 1 (extra info) gso.size (mss) = 1460 Because NETRXF_extra_info is not set, that''s all I get for that packet. In the IP header though, the total length is 1544 (which in itself

With GPLPV under 2.6.30, GPLPV gets the following from the ring: ring slot n (first buffer): status (length) = 54 bytes offset = 0 flags = NETRXF_extra_info (possibly csum too but not relevant) ring slot n + 1 (extra info) gso.size (mss) = 1460 Because NETRXF_extra_info is not set, that''s all I get for that packet. In the IP header though, the total length is 1544 (which in itself

I''m not able to start, destroy, or delete a DomU: > xen1:~ # xm start test4 > Error: Domain is already running > Usage: xm start <DomainName> > > Start a Xend managed domain >   -p, --paused                   Do not unpause domain after starting it    >   -c, --console_autoconnect      Connect to the console after the domain   

Hi, I install a guest Fedora inside the host Fedora. When I use the service xend status to check the status of xend. It shows xend is running. However when I use xm create xen1 to start the guest domain xen1, it failed. The corresponding file xen1 is in /etc/xen/xen1. The error msg is as follows: [root@phillis xen]# xm create xen1 Using config file "./xen1". Going to boot Fedora

Hi guys! I installed XEN 4.0 on Debian Squeeze but I cannot get the first DomU (not an image) started. Attached you will find /etc/xen/xen1.conf and the result of "xm create -c /etc/xen/xen1.conf" in xen1.log. Can you help me? What did I wrong? Is it about the fstab in xen1 (see also attached)? Many thanks in advance! Regards Stefan

Hello, I've been consistently attempting to make the setup mentioned in the subject work on the following hardware: Xeon E3 1275 (v1, Sandy Bridge) Asus P8B WS (Firmware: 0904 and 2009) 16 GB RAM Sapphire Radeon HD 7950 OC (Firmware: 015.013.000.010.000705) Linux 3.4.1 dom0, x86-64, pvops. Xen 4.1.2 (+ security patch) and 4.1.3-rc1. Old qemu-dm setup. (not new mainline qemu) Windows 7 64-bit

Hi, I have set up an ubuntu edgy guest domain on a fiesty host domain. The installation was successful but on running xm create -c baseimage, I get the following error message: Error: (22, ''Invalid argument'') The problem seems very similar to the one here: http://lists.xensource.com/archives/html/xen-users/2007-07/msg00361.html but I''m not able to figure out what the

Hi all, we are running CentOS 5.2 Xen virtualization system with the latest CentOS packages with couple of VMs on DELL PowerEdge. &quot;Sometimes&quot; the whole machine freezes without anything in log files, anything on the console. &quot;Sometimes&quot; really means we cannot define why or when. Sometimes the machine was idle with just one VM, sometimes quite busy with couple of

I''m getting the error: xend (12, ''Cannot allocate memory'') From the command line after the Dom-0 goes through a period of heavy memory usage. I don''t have any hard numbers on how to duplicate it, but I''ll give you the steps I''ve gone through to duplicate the problem. First, some information about my setup. It''s a new setup, and has

Greetings! Trying to to run a xen3 domU on a xen4 dem0 I run into problems. The xen server ''XEN1''(dom0) is openSUSE-11.3 (kernel 2.6.34) and xen-4.0.1. With qemu I created an image ''M08.raw'' from the SUSE-9.3 (kernel 2.6.11) and XEN-3.0 installation CD''s. The XEN modules were included in the installation. In M08.raw/boot I configured grub/menu.lst:

Hi folks, my problem: i am using putty and german layout. if i login from dom0 with "xm console xen1" i can login into the xen1 (domU) but how can i quit this console ? i have tested several commands: ctrl+5 ctrl+altgr+9 ctrl+c ctrl+x nothin happend. any hints ? -- Have an nice day, Viele Grüße Dominique H Schramm _______________________________________________ Xen-users

On a fresh reboot free: total used free shared buffers cached Mem: 3371340 448156 2923184 0 5328 77840 ---------- top: Mem: 3371340k total, 449044k used, 2922296k free, 5344k buffers ---------- xentop - 01:44:00 Xen 3.4.3-rc4-pre 1 domains: 1 running, 0 blocked, 0 paused, 0 crashed, 0 dying, 0 shutdown Mem: 4160828k total, 4022996k used, 137832k free CPUs: 4

I tryed te baloon out a domu and get: xm balloon VS01 1 Command balloon is deprecated But i need it... What can i doo? Dom0: Debian Etch - Kernel 2.6.18-6-xen-686 DomU: Debian Etch - 2.6.18-6-xen-vserver-686 _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

I''m getting the error: xend (12, ''Cannot allocate memory'') From the command line after the Dom-0 goes through a period of heavy memory usage. I don''t have any hard numbers on how to duplicate it, but I''ll give you the steps I''ve gone through to duplicate the problem. First, some information about my setup. It''s a new setup, and

hi, after rebooting my host, i can''t have anymore the networking: here''s my output of /etc/init.d/networking restart Reconfiguring network interfaces...SIOCSIFADDR: No such device eth0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device eth0: ERROR while getting interface flags: No such device Failed to bring up eth0. done. cat

Hi folks, KVM Virt-manager host - Debian 5.0 Starting; Gnome Applications -> System Tools - Virtual Machine Manager popup following error; Traceback (most recent call last): File "/usr/share/virt-manager/virt-manager.py", line 346, in <module> main() File "/usr/share/virt-manager/virt-manager.py", line 248, in main setup_logging() File

Hi folks, Win7 64bit R 1.12.0 I run following command on R:- > ToothGrowth > attach(ToothGrowth) > plot(dose,len) > matrics=lm(len~dose) > abline(metrics) Error in int_abline(a = a, b = b, h = h, v = v, untf = untf, ...) : plot.new has not been called yet Only a grey diagram is displayed without content > plot(abline(metrics)) Error in int_abline(a = a, b = b, h = h, v

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA512 as the screenshot [0] shows, my virtual machines aren''t showing up as running. This causes me a few problems. One being if I do xm shutdown SMGL-1 it simply powers it down, it doesn''t send the "shutdown signal" or whatever makes it go away :) I''ve done a from source install using the instructions mentioned [1].

I cannot boot domU: # xm create inhouse Using config file "inhouse". Started domain inhouse # xm list Name ID Mem(MiB) CPU VCPUs State Time(s) Domain-0 0 123 0 1 r----- 27.4 inhouse 8 2048 0 1 ------ 11.4 # xm console inhouse Linux version 2.6.12.6-xenU ( root@xen1) (gcc version 4.0.2 20050901 (prerelease)