similar to: xen 3.3 , drbd , centOS 5.2

Hi, I've upgrade the kernel to the latest version (C5) and after the update the drbd is not being loaded at reboot time. My previous running kernel was 2.6.18-164.el5. I've checked the /lib/modules/ and /lib/modules/2.6.18-164.10.1.el5/weak-updates/drbd82/drbd.ko -> /lib/modules/2.6.18-164.el5/extra/drbd82/drbd.ko And /lib/modules/2.6.18-164.el5/extra/drbd82/drbd.ko exists 2004

Hi, I have a server with Centos 5 + DRBD installed and is working fine, but when i run yum for udpate system show this error: Transaction Check Error: file /etc/drbd.conf conflicts between attempted installs of drbd-8.0.12-1.el5.centos and drbd82-8.2.6-1.el5.centos file /etc/rc.d/init.d/drbd conflicts between attempted installs of drbd-8.0.12-1.el5.centos and drbd82-8.2.6-1.el5.centos file

I've got a pair of HA servers I'm trying to get into production. Here are some specs : Xeon X3210 Quad Core (aka Core 2 Quad) 2.13Ghz (four logical processors, no Hyper Threading) 4GB memory Hardware (3ware) Raid 1 mirror, 2 x Seagate 750GB SATA2 650GB DRBD partition run on top of an LVM2 partition. CentOS 5.2 2.6.18-92.1.6.el5.centos.plus DRBD 8.2 (drbd82-8.2.6-1.el5.centos) Kernel

Hi, I have two servers in a drbd primary/secondary setup. Everything was fine until I had to reboot both servers. The primary rebooted first, the secondary assumed fine, but when the (old primary) server got back online it was unable to mount the drbd fs complaining about the modules. I've tried to find out the problem but the servers seem to have the same setup rpm -qa | grep drbd

Ralph Angenendt, Fabian Arrotin, Akemi Yagi and I have been working on new DRBD packages for CentOS Extras. We have some packages that have been tested in the testing repository. LinBit has discontinued their 8.2 tree, so drbd83 will replace drbd82 in both CentOS 4 and CentOS 5 extras. DRBD 0.7.25 will remain in CentOS 4, however it gets no upstream support and I would recommend you upgrade to

FYI: This bug also breaks user supplied scripts (/etc/xen/scripts/block-*) that are needed to handle block device mounting other than "phy:" and "file:" disks. See attached email from debian-user mailing list. cheers -henrik -------------- next part -------------- An embedded message was scrubbed... From: Henrik Langos <hlangos-debian at innominate.com> Subject: Re:

Hello, This morning I noticed the following output from "yum update": Installing: drbd82 x86_64 8.2.5-1.el5.centos extras 209 k replacing drbd.x86_64 8.0.11-1.el5.centos As far as I'm aware DRBD works fine for me. Is there a way I can find out about the new release and weather I should upgrade? I can't figure out the CentOS issue tracking system

Hi, I''ve been building up a new HA system, running Xen on DRBD devices. Configuration this applies to: Debian Lenny xen-linux-system-2.6.26-2-xen-686 package |**|drbd8-modules-2.6.26-2-686 drbd8-modules-2.6.26-2-xen-686 As I''ve been building the system, I ran into an interesting problem, with two symptoms: 1. running VMs would come back up after a reboot, but would hang on

When I execute "yum upgrade" on both CentOS 5.0 Xen DomU and CentTOS 5.1 Xen Dom0 I get: --> Finished Dependency Resolution Error: Missing Dependency: drbd >= 8.0.12 is needed by package kmod-drbd-xen "yum list drbd\*" gives: Available Packages drbd.x86_64 8.0.12-1.el5.centos extras drbd82.x86_64

Hi, i''ve a problem with drbd 0.7.10 module on an xenU OS (testing). I''ve compiling drbd with "make clean all" then "make install" without error. modprobe drbd OK with no error too and now and trying to start drdb /etc/init.d/drbd start Starting DRBD resources: can not open /dev/drbd0: No such device or address [ d0 can not open /dev/drbd0: No such device

Hi. I have an old Xen para virt vm which I created using sparse file. Is there any way to convert this vm image to non-sparse without shutting down the vm?. Thanks Paras.

We're trying to setup a dual-primary DRBD environment, with a shared disk with either OCFS2 or GFS. The environment is a Centos 5.3 with DRBD82 (but also tried with DRBD83 from testing) . Setting up a single primary disk and running bonnie++ on it works. Setting up a dual-primary disk, only mounting it on one node (ext3) and running bonnie++ works When setting up ocfs2 on the /dev/drbd0

We're trying to setup a dual-primary DRBD environment, with a shared disk with either OCFS2 or GFS. The environment is a Centos 5.3 with DRBD82 (but also tried with DRBD83 from testing) . Setting up a single primary disk and running bonnie++ on it works. Setting up a dual-primary disk, only mounting it on one node (ext3) and running bonnie++ works When setting up ocfs2 on the /dev/drbd0

Hello all, When I live migrate my centos guest from node1 to node2, I can ping the guest, but on node 2 if i do: xm console guest01 , I am not able to access it. When migrating back to node1 , I can access the console. What I noticed is, to access the console, the node ''s drbd resource/disk needs to be in primary status . Is it typical or only I am having this problem. Is there any

All, There are drbd82 RPMS for CentOS-4 and CentOS-5 (i386 and x86_64) for testing here: http://people.centos.org/~hughesjr/drbd/ These are designed to be able to live in the same repository as the current STABLE versions. These RPMS are designed as CONFLICTS and not upgrades as there may be some manual actions to upgrade, especially on CentOS-4. Here is an article on the upgrade process:

Which cpu is hit when domU does the heavy disk IO? dom0 cpu or domU cpu? I can see tapdisk in dom0 eating CPU. I have (dom0-cpus 1) setup in xen config. Thanks! Paras. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

hi, I have two machines, machine1 and machine2 both in the same network. The command I have been using to install a paravirt guest is virt-install --name=test --ram=512 --vcpus=1 --file=/dev/vgraid/puremessage-vm-root --paravirt --location=http://mirror.centos.org/centos-5/5.2/os/x86_64/ In machine 1 it is working. But not in machine 2. It is not able to retrieve or access url in machine 2.

Hi, I don't have ifcfg-eth1 in my /etc/sysconfig/network-scripts. But when I do ifconfig eth1 I can see output as below. If I do ifconfig eth12 , I don't see anything which i am assume is normal. eth1 Link encap:Ethernet HWaddr 00:24:E8:44:DB:CC BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0

My CentOS 5.4 box has a single HBA card with 2 ports connected to my Storage. 2 Luns are assigned to my HBA card. Under /dev instead of seeing 4 devices I can see 12 devices from sdb to sdm. I am using qlogic driver that is bulitin to the OS. Has any one seen this kind of situation? Paras -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi I have two box xen 3.2.1 and 3.3. On the 3.3 box I can''t use drbd as a device in the domu cfg. xm create -c test.cfg Using config file "/etc/xen/test.cfg". Error: Block device must have "phy", "file" or "tap" specified to type cat /etc/xen/test.cfg # Configuration file for the Xen instance test, created # by xen-tools 3.8 on Tue Sep 16