similar to: PPPoE in DomU exits with error

Peter Jakobi wrote: > Hi Jiri, > > you already tested an ancient userspace-only rp-pppoe? > I''ve still one active, and trying this you could validate > your the rest of your setup, before looking at possible > kernel changes anew (strace, ltrace, logs, whatever)... > Hi Peter. No I did not. Do I have to compile it? Can you give me more info what to do?

Under Linux, i can configure my DSL connection with pppoeconf (debian), without configure my Ethernet interface (eth0), just load kernel module fo ethernet interface, launch pppoeconf here is it. Another way is to configure the DSL interface (eth0 -> ALCATEL Speed Touch Home) with IP:10.0.0.1 so i can telnet or access with an web explorer the modem on 10.0.0.138. After i launch pppoeconf and

Hi, I am having problems establishing an adsl connection in dom0 (but ONLY in dom0, without xen everything is ok). Following is my setup/situation: 1. Installed clean Fedora 7 (with virtualization option selected) 2. Booted with the non-xen kernel & setup adsl. Adsl connection works without any problems. 3. Rebooted with xen kernel into dom0. 4. adsl connection can no longer be activated

I just bought a new cheap compaq presario sr5010nx and so far have been unable to get my dsl up and running on Centos5. pppoeconf on Ubuntu works just fine -- same machine -- same harddrive. I've run adsl-setup and system-config-network? (separately) numerous times without success. So far I suspect a missing driver but suppose it could also be a detection issue. Suggestions or workarounds

I just need a "temporary" pppoe server, that only uses PAP ___Can someone post a howto, just in a few lines, what to do?___ If I just do "pppd require-pap" then it gives this error: pppd: The remote system is required to authenticate itself pppd: but I couldn't fin any suitable secret (password) for it to use to do so. pppd is by default installed. and there are just a

Guys After reading through the archives I found some insightful ways to be able to shape traffic to pppoe clients from the server. I have two questions on the topic of setting up a pppoe server however... 1. The clients will all be connected to each other using a normal ethernet network, the segments connected with managed switches. The capacity is roughly 500 nodes. Will these pppoe sessions

Hi all, I am trying to install the PPPoe server rp-pppoe-3.8 from Roaring penguin on centos PC (Centos 4.3, Kernel release 2.6.9-34.EL) but not able to start it. When I start it it gives the error-- /etc/rc.d/init.d/pppoe status pppoe-status: Link is down (can't read pppd PID file /var/run/pppoe.conf-pppoe.pid.pppd) ror - /etc/rc.d/init.d/pppoe start Bringing up PPPoE

Hello to everyone, Can someone help me with hints on how to configure a pppoe gateway on a linux box with 200+ clients behind it ? I''ve read that user-space daemons give A LOT of CPU overhead. I''m opened to ANY solution ! -- Radu Cugut mobile: +40 742 045686 web: http://rcugut.has.it

hi, i need eth1 for an adsl connection via rp-pppoe (pppd). I was able to hide eth1 in Dom0, but how i use this device in DomU? Do i have to load the 8139too modul, to have eth1 in DomU? cu denny -- Sicherheit verständlich http://www.sides.de GnuPG Key http://pgp.upb.de:11371/pks/lookup?op=get&search=0xAB7D3FE0 _______________________________________________ Xen-users mailing list

hi! I'm trying to get zapras working in GSM csd network. Whenever a dialup call is initiated from the mobile to the * gateway the following appears in the log and zapras terminates. Phone gives the error dialup not answered. ==> /var/log/messages <== pppd[2310]: Plugin zaptel.so loaded. pppd[2310]: Zaptel Plugin Initialized pppd[2310]: Using zaptel device 'stdin' pppd[2310]:

Please point me in the right direction.... My ISP is giving me an IPv6 prefix, but to get that I have to: The current Speedstream ADSL router will be configured as a bridge. I will have to set up a Linux (read Centos, I hope) router that will connect ethernet to the Speedstream but run PPPoE to his network and get both the IPv4 and IPv6 route delegations. There is no easy way that I know of

Hi, I currently connect to my ISP via my adsl modem in bridge mode and PPPoE. I am due to put a second PPPoE ISP onto my firewall box which will give me ppp0 (general) and ppp1 (static leased line). The static leased line will run a number of services on its static IP and it is therefore imperative to make sure rules defined for the static line are assigned to the correct interface. I need this to

I need some suggestions, I want to limit the up and down bandwidth of PPPoE users that are terminated on a Linux router (kernel 2.6). What are my options, can I apply tbf qdisc on a ppp interface? That would limit the download, what about the upload? Any suggestions are welcome. -- damjan | дамјан This is my jabber ID --> damjan@bagra.net.mk <-- not my mail address!!!

Hi, we are currently using pppd to connect to the net through pppoe. Some providers seem to propose ipoe instead of pppoe and I cannot find any clue on how/where/if_possible to set up such connection in CentOS. Anybody has any experience with ipoe...? Thx, JD

hi all. i am currently now serving PPPoE in my area. i had a script generated from tcng that worked perfectly before i started serving PPPoE. the issue is not in the script it self BUT in that "tc" code is not shaping on the ethernet anymore BUT INSTEAD on the pppX devices. I tested it and talking jargon, what should i do? The issue is that for each PPPoE login, PPPoE-server

Hi There, We currently using iproute2 for load balancing. However we need more upload speed as we load balance over 3 dsl lines. I''ve been looking for a way to combine the upload speed to more faster. Found a site called www.upstreaminter.net where these guys bond the adsl channels to improve uploads, Since downloading is problem as its need to know the ip address of the downloader they

Thanks: To Stef and Tobias Geiger for giving me the answer. I used the prio to get the order right. Don't know why I did'nt think of it myself. Compression: Another thing that might be useful to the list is the use of compression (Deflate etc.) to get better bandwidth across links. This requires a Linux router at both ends of the link. I got the idea from a product called Peribit see

Hi. I am new to CentOS (Debian user) and I am looking for way how to install CentOS 5 on domU in the way that I have it directly on dom0 LVM partition. If I install it with virtual-manager then the installation program takes that partition as a disk and then creates new partitions on it. I don''t want it that way because I cannot then mount it from dom0. Is there some way how to

Hi List, I read this list for nearly two years and learnt a lot, but now i have a very strange problem I can''t solve.. I have a firewall machine running Debian, which connects a small office to the internet via a DSL-line (with pppoe) and which is running Shorewall. It allows all outbound traffic and accepts pptp, openvpn and ssh-connections (on a non-standard port) from the internet.

I''ve got a linux router pushing 600-1000 pppoe connections through it. I''m getting a screen error "Neighbor Table Overflow" after this box has been up for between 1 week and 1 month. When this is happening, routing slows to a crawl if at all. Then dies. I''ve added: # Added to stop "neighbor table overflow" messages in the kernel