similar to: Does XEN support crash carts?

I''m currently trying to build modules against the kernels created with Xen 3.0.5rc4. This used to not be such a problem, as Xen created a kernel directory and the built in it. Plain Jane, nothing fancy. I''ve noticed that somewhere since I did this (which was as recent as 3.0.4-1) the kernel build now does things a bit different. Apparently there is some sort of

Hi! Say I export an LVM logical volume from dom0 as /dev/xvda to the domU: disk = [ ''phy:xenimages/stan,xvda,w'' ] No I can lvresize xenimages/stan in dom0, but the domU stays ignorant of this change. How could I propagate the resize to the domU without rebooting or temporarily breaking its connection to /dev/xvda? Sort of a SCSI rescan, perhaps? -- Thanks, Feri.

I've been asked to create a graphical "call-queue" manager. That is, use the existing call queues application but allow a way to view what's coming and attach information to it. As far as the "attaching information" that's in the realm of my application, but I'm trying to figure out if the internals of queues are exposed through any interface. Any help there?

Hey Everybody, You may remember be as the one that was generally running in circles trying to get ADSI phones to work? Well, five phones later, I've got a phone and a code that works to program it. I have been discouraged from just posting it to an e-mail forum, but I have been encouraged to get it embedded in the program. Is this possible? How should it be done? Next, after getting it

Ok, so I figured out my problem with my pt480s. But, now I have a few more. 1. When I dial into the voicemailmain or voicemailmain2 application, the phone and * start talking adsi, but then the phone tells me "programming download canceled, services is full.", but my services list isn't full, only "Asterisk PBX" occupies slot 2, slots 1, 3 and 4 are available. Any ideas?

Is there any reason why this combination shouldn't work? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031105/bc043610/attachment.htm

<some stuff snipped for brevity> > > I didn''t want to make the Xen kernel the default until I was > > sure that it would boot correctly. > > Sensible. > > > > When I put the root=LABEL=/ on it I get an error: > > > > mkrootdev: label / not found > > Yes, I''ve had problems using "LABEL=" on my system too - and

New complile causing trouble... How do you enable MARK2 echo can with DAGGRESSIVE_ SUPPRESSION? looks like zconfig.h ..but I have quite a bit of echo on a bridgeded call and echocancelwhenbridged=no John ------------------------------------------------------ This message was sent using Monroe-Woodbury's WebMail. http://webmail.mw.k12.ny.us/ This e-mail was scanned and found clean by

With regards to the IRQ sharing situation on 400P/X100P cards how would I know if I can use IO-APIC? I am running RHEL 3 on a Dell PowerEdge 1400SC. RHEL installs without IO-APIC support. Is this because RH is overly conservative or because it queried my machine and that is the appropriate option? Does RHEL 3 have a kernel for IO-APIC if appropriate or am I expected to do a custom kernel build

Dear Sirs, I'm running an Asterisk 0.9.1 in a Fedora Core 2 box. I installed a X100P card on my box and when i try to load modules i am rejected. When i type modprobe zaptel my Fedora respond : "FATAL: Module zaptel not found." . The same uccurs when i type "modprobe wcfxo" May you help me. Thank you in advance Juanjo

> -----Original Message----- > From: Petersson, Mats [mailto:Mats.Petersson@amd.com] > Sent: Thursday, March 01, 2007 10:12 AM > To: Foreman, Tim > Cc: xen-users@lists.xensource.com > Subject: RE: [Xen-users] Xen 3.0.4 on RH EL 4.4 - can''t make it boot > kerne l > > > > -----Original Message----- > > From: Foreman, Tim [mailto:tforeman@ibsys.com]

Hi All, Please bear my ignorance but what is TDMoE used for? Illustrations with practical applications, scenarios or set ups will be most appreciated. Thanks Luan

Sirs, According to RFC 2705 (MGCP), these are the parameters that are used in the transactions: ReturnCode, Connection-parameters <-- DeleteConnection(CallId, EndpointId, ConnectionId, [Encapsulated NotificationRequest,] [Encapsulated

Good Afternoon, I have an Asterisk box that is acting like it is passing "core show" before every command I type. For example, if I type sip, I will get "No such command 'sip' (type 'core show help sip' for other possible commands). Any ideas? -- -jayson

We recently added a disk to our Coraid SAN. We''ve used tons of devices off of this SAN with Xen before, but this time we experienced some weird behavior. I configured a DomU to have the device directly offered as a disk (i.e. ''phy/dev/etherd/e1.1,sdb1,rw''). When I tried to boot it, an xvd process showed up as usual. However, it consumed 100% processor

I''ve been looking at perhaps sharing some data between various domUs. Specifically, a Gentoo Portage tree. I found XenFS (http://wiki.xensource.com/xenwiki/XenFS). Is this going anywhere? I couldn''t get it to build. -- Jayson Vantuyl Systems Architect Engine Yard jvantuyl@engineyard.com 1 866 518 9275 ext 204 _______________________________________________ Xen-devel

> -----Original Message----- > From: Foreman, Tim [mailto:tforeman@ibsys.com] > Sent: 01 March 2007 16:02 > To: Petersson, Mats > Subject: RE: [Xen-users] Xen 3.0.4 on RH EL 4.4 - can''t make > it boot kerne l > > > Ok, that didn''t tell me what I wanted to know, how about > the output of > > "mount"? > > > > I want to

I have a WxRuby application that takes a few inputs from the user and uses that information to search through a large file for matches. The application works very well, with one exception. If I click anywhere in the frame while the application is searching through the long file, the application hangs. Has anyone experienced anything similar to this? Any suggestions on how I can fix this? Thanks

How do you make a button inactive, so that it is visible, but it will not respond to clicks? Thanks Jayson

I''m new to the group, so apologies in advance if I repeat a question that''s already been asked and answered. First of all, I''m very happy to see an open-source alternative to commercial configuration automation tools. My question is this: I manage a collection of tools with web-based administration. They have no external config files, and store their config data in the