similar to: Xen and cciss (Smart Array 5300)

Dear ALL, I have encountered an issue while installing xen4.1.2 from source. No problem encountered while xen installation.While booting towards XEN kernel, i encountered the folowing error ******************** setuproot: moving /dev failed : No such file or directory no fstab,sys mounting internal defaults setuproot: error mounting /proc setuproot: error mounting /sys Kernel

CentOS Errata and Enhancement Advisory 2013:1130 Upstream details at : https://rhn.redhat.com/errata/RHEA-2013-1130.html The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) i386: 31dfe744e171002bdc77819e73e9900aa039129d94f4ae36405d87a954292da0 kmod-cciss-3.6.28-2.el5_9.i686.rpm

Since they do not present a block.device property via HAL, this patch goes directly to /dev/cciss/ and pulls together any devices found there. It ignores anything that ends with p# since those are partitions and not block devices. Signed-off-by: Darryl L. Pierce <dpierce at redhat.com> --- scripts/ovirt-config-storage | 7 +++++++ 1 files changed, 7 insertions(+), 0 deletions(-) diff

Signed-off-by: Mike Burns <mburns at redhat.com> --- scripts/ovirt-config-storage | 21 +++++++++++++++------ 1 files changed, 15 insertions(+), 6 deletions(-) diff --git a/scripts/ovirt-config-storage b/scripts/ovirt-config-storage index c8fb049..46f7e19 100755 --- a/scripts/ovirt-config-storage +++ b/scripts/ovirt-config-storage @@ -83,6 +83,7 @@ get_multipath_deps() {

Greetings, ----- Original Message ----- > I've recently come across a thread in the CentOS forums [0] regarding > the solution to getting hardware requiring the cciss driver, such as HP > ProLiant G5 systems, to install and boot with CentOS 7. The thread was a > start in the right direction, but I believe I've determined a better > workflow and feel that it would benefit

All, I would like to run the following issue past the list to confirm that my problem analysis makes sense or whether I missed something: We have a HP ML370G6 server with VT-x and VT-d enabled in the BIOS. It is equipped with two Smart Array HBAs - one connected to the HDD array (SmartArray P800) and one connected to an LTO tape drive (SmartArray P212). Both controllers use the same driver

Hello All, Hardware: HP ML570 2G Ram Dual 2.8G procs Compaq 5300 Smart Array Controller Software: Centos 4.1 I yum-med a server last week and rebooted it. When it came up, it stopped. Looking at the console, I got: ---snip Setting Hostname: OK Checking root filesystem: /dev/cciss/c0d0p10 is mounted, e2fsck cannot continue, aborting failed *** an error occurred during the file system check

Hi. I am trying to boot Xen 2.0.5 on an HP DL380 G3. It won''t. The box has an "HP Smart Array 5i" that when running normal Linux is handled by the CCISS driver. I suspect that this is what is not supported in the stock Xen kernel. Am I correct that I need to build a kernel from source ? According to http://lists.xensource.com/archives/html/xen-devel/2004-11/msg00709.html there

I have continued on with my attempts to get p2v working will little success. I have changed my server to Fedora 16 and finally got an XP with a single SATA disk (sda) to work. I think that this means that the current virt-p2v.iso just doesn't work with the packages that are available on Centos 6 at the moment. However, the machines that I currently need to actually migrate all have

Hi Can anyone help me find which option I need to activate to build the the xen0 kernel with cciss support? Thnaks for your help. Shaz _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

I've recently come across a thread in the CentOS forums [0] regarding the solution to getting hardware requiring the cciss driver, such as HP ProLiant G5 systems, to install and boot with CentOS 7. The thread was a start in the right direction, but I believe I've determined a better workflow and feel that it would benefit the community to have this published either in the release

Mm, I have a big Quad-Opteron.. thing.. that I''m trying to get Xen onto. I''ve used the 3.0.2 binary-install mode, updated menu.lst as per the README, but I need an initrd which contains the HP cciss RAID driver, and no Xen initrd image was installed into /boot. Now I notice xen-3.0.2-2-install/install/lib/modules/2.6.16-xen/kernel/drivers /block/cciss.ko But I

On Wed, May 25, 2011 at 12:41 AM, JAMES BOND 123 007 <james123007@gmail.com> wrote: > Hi , > I saw your thread post at > http://web.archiveorange.com/archive/v/ZvO4jnaavtTfcyqnHoRX > , about problems with XEN 4.0 installation. > I have the same problem and my machine is similar to yours( HP Proliant > DL380G6, 4GB-RAM) This question is better asked on the xen-users list.

I am trying to build lustre-1.6.6 against the pre-patched kernel downloaded from SUN. But as written in Operations manual, it creates rpms for 2.6.18-92.1.10.el5_lustrecustom. Is there a way to ask it not to append custom as extraversion. Running kernel is 2.6.18-92.1.10.el5_lustre.1.6.6smp. -- Regards-- Rishi Pathak National PARAM Supercomputing Facility Center for Development of Advanced

Original the array was attach to an HP server via a Smart Array Controller.(which I didn't setup, I just inherited the problem) This controller no longer recognizes the array even though the front panel of the array indicates its intact. I then took the array and plugged it into my Centos server and it recognized it ... cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun:

With kernel 2.6.30-rc2-git6 and prior I am having problems mounting ext4 partitions after reboot. A successful mount looks like this: /dev/cciss/c0d0p8 on /squid-cache0 type ext4 (rw,noexec,nodev,noatime,data=writeback,errors=panic) /dev/cciss/c0d0p9 on /squid-cache1 type ext4 (rw,noexec,nodev,noatime,data=writeback,errors=panic) /dev/cciss/c0d0p10 on /squid-data type ext4

Hello I have the feeling this may not be the right forum for the following question, but I d like to try it here anyway: This is the case: I had a 3x72GB HDD RAID5 shared external disk drives (HP MSA500), totalizing about 145,6 GB of data. I needed to increase the available amount of data, so I added a 4th 72GB HDD and using HP ACU I expanded my existing RAID5 Array, I have now about 218,5

Hi all, I discovered lately that two of my XEN servers suffer from a really bad disk throughput - in domU as well as in dom0. All of them run Debian/Etch, Kernel 2.6.18-6-xen (orig. Debian) with XEN 3.2 (backported). The software versions seem to be ok for most machines: Lenovo A57 with S-ATA and (E8200, VT enabled): up to 90MB/s Shuttle, FB61 based, ATA-Disk (Celeron, no VT): up to

Chris: I can consistently reproduce I/O stalls when running fstress (as found in Autotest) against a six volume btrfs filesystem mounted without options. The volumes are independent disks from RAID controllers, and the test systems are eight core Intel and AMD machines running current btrfs-unstable. The stalls occur at variable times into the runs. The affected system ceases to do I/O

Send CentOS-announce mailing list submissions to centos-announce at centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request at centos.org You can reach the person managing the list at centos-announce-owner at centos.org When