similar to: Problem with network-bridge script and veth0

When does vif0.0 get created? Is there some shell magic? I''m trying to figure out how to do a similar peth1/veth1 split for eth1. -- Nicholas Lee http://stateless.geek.nz gpg 8072 4F86 EDCD 4FC1 18EF 5BDD 07B0 9597 6D58 D70C _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel

Dear I need create second bridge xenbr1 for separate traffic between my virtual machine , I following this step but show message that Link veth0 is missing, how I can create veth0 ? When I run script for create xenbr1 ./network-bridge netdev=eth1 bridge=xenbr1 start Shwo this message Link veth0 is missing. This may be because you have reached the limit of the number of interfaces that the

Hi, I''m using RHEL linux 5.1, I can''t add the another NIC to my virtual machine. # /etc/xen/scripts/network-bridge start Link veth0 is missing. This may be because you have reached the limit of the number of interfaces that the loopback driver supports. If the loopback driver is a module, you may raise this limit by passing it as a parameter (nloopbacks=<N>); if the

Hi, I am using Xen 4.1.1 with Linux 3.0.1 kernel. Previously (Xen 3.4.4 and linux kernel 2.6.18) Xen by default created veth0 <--> vif0.0 pair in dom0. With Xen 4.1.1 these pairs are missing in dom0. Using command ''ip link add type veth'' I can create veth0 and veth1 but vif0.0 is still missing in dom0. (When new domU created I can see vif1.x created) Could you please help

Hi, I am using Xen 4.1.1 with Linux 3.0.1 kernel. Previously (Xen 3.4.4 and linux kernel 2.6.18) Xen by default created veth0 <--> vif0.0 pair in dom0. With Xen 4.1.1 these pairs are missing in dom0. Using command ''ip link add type veth'' I can create veth0 and veth1 but vif0.0 is still missing in dom0. (When new domU created I can see vif1.x created) Could you please help

Hello, I have a xen server that needs to run a domU on a different vlan than xen''s. I have configured my switch (a cisco catalyst) to tag every untagged packet to the default vlan (the one in which is dom0) and to accept tagged packets (for that domU). I have xenbr0 linked with the eth0, the default network. Then I run * vconfig add eth0 101 -> To create a virtual interface with

Hi, This is my setting: I have a Logical Volume /dev/VG/suse with Suse installed. I have added it to the grub and I can boot it and works perfectly fine. Now I am running /dev/VG/root which is running Xen0. I have created a Xen config file to boot a VM with disk: /dev/VG/suse. In other words I want to boot /dev/VG/suse as a virtual machine. Below is what I am getting at boot time :

I have a domU configured with two virtual ethernet interfaces - one on a private bridge and one to the outside world. If I cat /proc/net/dev (or loop round the interfaces using SIOCGIFNAME) there are loads of them? Should they all be there ? I''m using the same kernel for dom0 & domU. Inter-| Receive | Transmit face |bytes

Hi All, We have a single Centos 5.11 server running a xen hypervisor that went down hard after an extended power outage this weekend. I'm mostly familiar for KVM as that is the majority of what our guests run under and have tried getting up to speed on xen bridging to no avail. The problem is that after the xen server spun back up, the previously defined xen bridges were lost. I've

Package: xen-hypervisor-3.0-unstable-1-amd64 Version: 3.0-unstable+hg11292-2 Severity: important My server is a dell 2950 server. Before the dom0 rebooting bug ocurred, xen was well even for hvm domU. By now i have tried xen-hypervisor-3.0-amd64 (3.0.2+hg9697-2) and xen-hypervisor-3.0-unstable-1-amd64 (3.0-unstable+hg11292-2), but both of them are unusable for me. for

When we create an L2 loop on a bridge in netns, we will see packets storm even if STP is enabled. # unshare -n # ip link add br0 type bridge # ip link add veth0 type veth peer name veth1 # ip link set veth0 master br0 up # ip link set veth1 master br0 up # ip link set br0 type bridge stp_state 1 # ip link set br0 up # sleep 30 # ip -s link show br0 2: br0:

Hello, I have got something strange when I done a /etc/xen/scripts/network-bridge status : 201: eth0: <BROADCAST,MULTICAST,UP,10000> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:15:17:8d:cb:1c brd ff:ff:ff:ff:ff:ff And when I done a /etc/xen/scripts/network-bridge I have got this : Link veth0 1 is missing. This may be because you have reached the limit of the number of

Hello. I use libvirtd on my Gentoo development system to manage both QEMU and LXC. When 1.0.3 came out, I updated to it from 1.0.3-r2, but 1.0.4 failed to start my LXC containers. I did not research the issue at the time, so I revert to 1.0.3-r2. Today I updated to 1.0.5 and my LXC containers still fail to start. I have not changed my domain XML at all. I am looking for suggestions on

On 12/07/2023 02:54, Kuniyuki Iwashima wrote: > When we create an L2 loop on a bridge in netns, we will see packets storm > even if STP is enabled. > > # unshare -n > # ip link add br0 type bridge > # ip link add veth0 type veth peer name veth1 > # ip link set veth0 master br0 up > # ip link set veth1 master br0 up > # ip link set br0 type bridge stp_state 1

On 12/07/2023 17:48, Ido Schimmel wrote: > On Tue, Jul 11, 2023 at 04:54:15PM -0700, Kuniyuki Iwashima wrote: >> When we create an L2 loop on a bridge in netns, we will see packets storm >> even if STP is enabled. >> >> # unshare -n >> # ip link add br0 type bridge >> # ip link add veth0 type veth peer name veth1 >> # ip link set veth0 master

I try to bring up xend but get this error in the xend-debug.log /etc/xen/scripts/network-bridge: line 62: ip: command not found Link veth0 is missing. This may be because you have reached the limit of the number of interfaces that the loopback driver supports. If the loopback driver is a module, you may raise this limit by passing it as a parameter (nloopbacks=<N>); if the driver is

Hello All, I'm trying to figure out why xen-utils-common 3.2 doesn't suport bridging on multiple interfaces. I've been digging around /etc/xen/scripts/network-bridges. And modified it so that during boot, when executed the script writes into /tmp/netbr file, but I commented out code that actually creates bridges. I discovered that this script is called three times during boot, I

> > When you run xend it runs network-bridge which creates the bridge, > > renames eth0->peth0 and veth0->eth0 and brings the new eth0 back up. > > kewl, thx Ian. i see network-route doesnt do this. i think > thats a good thing. do you forsee that changing? I expect that in most routed configurations people use their own network script rather than using the

> That''s great, except when you need *two* bridges, for two > independent subnets, and there is no, as far as I can see, peth1. You can have multiple vethX interfaces on recent builds -- see netback/loopback.c. I think the current default is a rather miserly 1 (and should be increased), but can be set on the command line. Ian > Em Wednesday 14 September 2005 16:30, John

Hi, I try to get networking running with xen 3.2, but it seems I fail miserably. I am on sles10sp1, with xen 3.2.0, and kernel rpm''s installed from SP2. I configured in /etc/sysconfig/network the NETWORK_LIST: NETWORK_LIST="bridge,0,default,00:DE:AD:BE:EF,192.168.8.13/24,dhcp-off" but an ifconfig xenbr0 still shows the mac address of peth0 fe:ff:ff:ff:ff:ff. Initially, I