similar to: Error: Kernel image does not exist: /boot/vmlinuz-2.6.16-xen3_86.1_rhel4.1

Hello All, This is my first post to this list, though I''ve been following Xen''s development since the beginning (well, after news about it first broke, anyway). I''ve been wanting to try it out, and hopefully consolidate a few servers here, so I finally made the decision to do just that. I''ve downloaded the RHEL 4.1 RPMs from the xensource.com website, and

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all, I don't know if this is the right list, but here goes what happened recently to me. I have an IDE disk (hda: QUANTUM FIREBALLP AS20, ATA DISK drive / hda: 39851760 sectors (20404 MB) w/1902KiB Cache, CHS=2480/255/63, UDMA(100)) connected to 00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 12) I've decided to make a

Hi, I've been foolish enough to let Partition-Magic move/resize/etc. my partitions without a prior backup. My ext3 /dev/hda7 (was RH 9) is no longer recognised by fsck. I tried fsck -b 8139, 32768 and 65536 - but am not quite sure about if these are the right ones to try. So far I created another partition with same number of blocks and did a backup with dd if=/dev/hda7 of=/dev/hda8

> [6] ctivating swap partitions: swapon: /dev/hda7: No such device or address > [6] [FAILED] > [6] ioctl 80041272 not supported by xl_block > [6] Finding module dependencies: depmod: Can''t open /lib/modules/2.4.24-xeno/modules.dep for writing > [6] [FAILED] > [6] Checking filesystems > [6] Couldn''t find matching filesystem: LABEL=/policy Edit your

Hi, "Mircea Popescu" <nufarul.alb at go.ro> schrieb am 29.01.02: > I have this problem: > I've partitioned my hard drive with PQMagic 7 in the following way: > hda1 - fat32 > hda2 - ext2 > hda3 - fat16 > hda4 - extended > hda5 - Linux Swap > hda6 - fat32 > hda7 - ext2 > hda8 - fat32 > > I've put syslinux on

I was trying to use my windows RIS server to deploy linux so as to require user authentication. After seaching the internet I found that it was possible but not very well explained after alot of tinkering I eventually got it to work. Here is my documentation so hopefully others can do it in less time than I, feel free to comment and improve.. ************************ On RIS Server Create

Hi to all: I''m trying to build an Oracle Rac10gR2 under 2 xenitized RedHat 4 nodes ( The host domain is debian 3.1 ) Well, all goes well until time to mount ocfs2. For Rac10gR2 I need to mount ocfs2 partitions with the datavolume option, but latests versions of ocfs2 doesn''t comes with this option ( you can enable the O_DIRECT feature directly in the init.ora file, with the

Good morning, I try to use the last release of ext3 patch with a 2.4.10 linux kernel. I have two troubles : - when the kernel is booting, I receive : NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 208k freed Adding Swap: 128480k swap-space (priority -1) Adding Swap: 128480k swap-space (priority -2) Why my root

Add a couple of documentation details about PV-GRUB support - the menu.lst content can be passed as a ramdisk. - virtual partitions are not supported. Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> diff -r b8d2a4134a68 stubdom/README --- a/stubdom/README Wed Mar 03 17:41:58 2010 +0000 +++ b/stubdom/README Wed Mar 03 20:42:53 2010 +0100 @@ -52,11 +52,17 @@ extra =

I am trying to use data=journal on my root file system. I have separate slices on which journal=data works fine on all of them, except root. I have tried putting rootflags=journal=data on my kernel line in Grub, but I get a kernel panic. I'm missing something simple, I jut know it. It can't be the kernel version because it works on the other slices. My etc/fstab file is as follows:

Suse 10.1 AMD64 Xen3 New to Xen. The dom0 is up and running. I am trying to get my first domU working. My approach is to use precompiled images from jailtime.org. After some manual tinkering with the .cfg file the domU proceeds to boot but stalls with the following error. I cannot get past this - any ideas ? Brian Using config file "/etc/xen/vm/vm1". Started domain vm1 Bootdata ok

Hello, unfortunately I got some trouble using ext3 - the system hangs when working in a certain directory. Not completely, I can switch between consoles and reboot with SysRQ, but cannot do anything which requires disk IO: not start any applications, not umount, nothing. I could send the strace output, but I don't think this would help anyone. Sorry, but I don't have a clue where to start

Hi folks, For unknown cause I encounter following mounting problem; # /mnt/hda8 mount: wrong fs type, bad option, bad superblock on /dev/hda8, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so # dmesg | tail via82cxxx: timeout while reading AC97 codec (0x9A0000) via82cxxx: timeout while reading AC97 codec (0x9A0000)

Hi there, I'm using xen-3.0.2.2-86.1_rhel4.1 on a Redhat AS 4 update 1 for i386. When I create a new domU with the following conf file, everything is ok: ##BEGINNING## kernel = "/boot/vmlinuz-2.6.16-xen3_86.1_rhel4.1" ramdisk = "/boot/initrd-2.6.16-xen3_86.1_rhel4.1.img" builder='linux' memory = 1024 name = "myvm" vcpus = 8 vif = [

Hi everyone! I came across a problem when I used xm create to create a domainU on my machine. I installed xen-3.0.4 on my computer, running Fedora 6, kernel version is 2.6.18-1.2798.fc. I want to install a Fedora 6 on xen, so I write the following config file, named fc6.cfg kernel = "/boot/vmlinuz-2.6.16.33-xenU" memory = 128 name = "fedora.fc6" dhcp = "dhcp" disk =

Hi, I''m getting a kernel panic when booting a Dell PowerEdge 1850 with kernel 2.6.16-xen3_86.1 which I installed from the xen-3.0-x86_32-rhel4.1.bin.tar package I got from XenSource. My /boot/grub/grub.conf configuration is this: title Xen (2.6.16-xen3_86.1) root (hd0,0) kernel /xen-3.gz com1=115200,8n1 noreboot module /vmlinuz-2.6.16-xen3_86.1_rhel4.1

Hi, Just got Fedora FC1 vanilla 2.4.25kernel+libata8patch booting problems, FC1 complains that it can not automatically find&found partitions specified with "LABEL=" in /etc/fstab, and then falls me into repair mode. In the repair mode I can mount it manually without any problems. More interesting are: 1) I have several partitions specified with "LABEL=*" in

I've posted here with this problem before, and while several people DID try to help, nothing seems to work! Here's the situation (again): I have a Linux box (Mandrake 7.0) running Samba (2.0.6) compiled from source. I can mount/read/write the linux shares just fine, but when trying to write to my Win98 shares (which mount perfectly), I get "permission denied". This only

On Wed, Dec 9, 2015 at 1:07 PM, Emilio Lazo Zaia via Syslinux <syslinux at zytor.com> wrote: > I thought I've found three bugs on syslinux 6.03: Just to be clear, is this only affecting vesamenu.c32? > (1) With sample config file as is, i.e. leaving commented MENU VSHIFT and > MENU COLOR UNSEL but uncommented MENU COLOR SEL: > > A black "border" is displayed

Hi all, I have a multiboot configuration with 2 linuxes using grub as a boot loader. Both are working installations independently of Xen. I have installed Xen kernels on both systems. I want to boot one of the two systems as Domain 0, and the other as Domain 1 so that I can run the two systems simultaneously. Is this possible? If so, how? If not, why not. TIA, nb a domU kernel from a