similar to: xm migrate with cowloop

Hello ! Is anybody using cowloop (http://www.atconsultancy.nl/cowloop/) with XEN ? i want to use this for saving diskspace and time for copying rootfs-images. the module compiles and loads fine (was done by a colleague) cowloop - (C) 2005 AT Consultancy/AT Computing cowloop - version: 2.15 cowloop - info: www.ATConsultancy.nl/cowloop cowloop - maximum allowed cowdevices: 16 cowloop -

Hello, I have 2 Dell 1955 blade servers, running RHEL5-Xen. I''m testing the migrate functionality from one blade to another. I can start the domain, move it to one blade (minor delay/packet loss) and everything is fine. When I try to move it back to the original blade the migration fails and the DomU crashes c1b1 = Blade 1 (192.168.131.201) c1b2 = Blade 2

Package: xen-utils-4.1 Version: 4.1.1-3 I have an HVM domU which was created with xen-utils-4.0 (and Xen 4.0 hypervisor of course). Recently I've upgraded to Xen 4.1 and xen-utils-4.1, but after a reboot I was unable to do anything with it: "xm start" caused "Domain is already running" error, while "xm shutdown" simply hadn't printed any error messages, only

I am running a 64 bit dom0 with a stock Debian Squeeze xen hypervisor and kernel. On top of this I am running a PV 32 bit domU that is passed two PCI network cards. This set-up had been working well for over a year, however there was a recent hypervisor update so I rebooted the dom0. Unfortunately now the domU that is being passed the two NICs is no longer able to create a PPPoe connection to

Hi, I was just wondering if it is possible to cause a script to run (configured in the domu.cfg file) each time "xm create domu.cfg" is run, but before the machine is actually started? ie, I''d like to "setup" the disks for the VM before xen/qemu tries to use the devices and allocate to the domu. I''m using xen 4.1.3 on Debian testing, and using the xm

Hi all, Anybody know what it means for a DomU to show up in the "xm list" as follows: Name ID Mem VCPUs State Time(s) Domain-0 0 256 2 r----- 43929.3 Clonezilla 16 512 1 ------ 6.2 The domU "Clonezilla" does not have an "r" state

Hello, I read the blktap readme; there is a section there titled: Mounting images in Dom0 using the blktap driver. It says there that you can mount an image by: xm block-attach 0 tap:aio:<FILENAME> /dev/xvda1 w 0 mount /dev/xvda1 /mnt/disk <--- don''t use loop driver This option also appears in: http://wiki.rpath.com/wiki/Xen_DomU_Guide I assume that this option is not

I tryed te baloon out a domu and get: xm balloon VS01 1 Command balloon is deprecated But i need it... What can i doo? Dom0: Debian Etch - Kernel 2.6.18-6-xen-686 DomU: Debian Etch - 2.6.18-6-xen-vserver-686 _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Hi list, I am running a virtualized server. Dom0 uses Xen 3.2.1 with Debian Etch and a custom kernel 2.6.21 created by my webhosting company. I install my domU using debootstrap for a Debian Etch with 2.6.18-6-xen-amd64 kernel. Everything works well except the fact that once the VM is started I cannot "xm console" into it. It only works while it is booting and while it is shutting

Hi everyone, I generated my own DomU guest using opensuse''s yast dirinstall and stored it on a seperate iscsi target. I created it as a DomU on my Domain0 (2.6.25.16-0.1-xen kernel) successfully, using the following configuration: name = "vm01-opensuse11-base-LAMP" memory = 256 kernel = "/boot/vmlinuz-xen" ramdisk = "/boot/initrd-xen" root =

I want to get couple of DomUs running with Xen. I installed Xen 4.1.5 from source on a Fedora 17 Dom0. I did some reading on configuring DomUs using xl/xm and cfg files. http://www.fclose.com/b/linux/2544/setting-up-lvm-backed-xen-domu/ http://www.fclose.com/w/Setting_Up_Xen_DomU_on_Fedora:_Unmodified_Fedora_on_Top_of_Xenified_Fedora_Xen_Dom0%23Install_Fedora_12_Linux_via_Internet So basically I

Hello, I was looking to create a Xen DomU with a .iso image saved in the hard disk. I ran into some trouble with http based install, hence looking at this option. This is what i have currently. Just wanted to know if I am on the right track here, and hoping to get some tips if somebody has similar experience. I compiled Xen 4.1.5 from source on a Fedora 17 Dom0, and I want to create DomU

Package: xen-utils-common Version: 4.3.0-3 Severity: normal Dear Maintainer, I've just set up a fresh Jessie system using the installer dated 2014-03-05, then installed and enabled Xen 4.3. I've done this quite a few times before using Wheezy and 4.1. I set up xenbr0, then created a test domU using xen-create-image, which completed without issue. However I was unable to start the new

I am running on the Centos 6.5 x86_64 boot disk. # uname -a Linux localhost.localdomain 2.6.32-431.el6.x86_64 #1 SMP Fri Nov 22 03:15:09 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux I have been running ddrescue for a while and now it is time to check the progress. I want to take the oldhd.img output from ddrescue and load it to satrt performing recovery (LVM, then filesystem) but I want to do a copy

Package: xen-utils-common Severity: minor Version: 3.0.3-0-2 During a domU state transition (at least on domU shutdown), "xm list" seems to occasionally fail. This is only intermittent, but it could cause problems if there are automated tools (or unaware humans) inspecting the output or return codes of "xm list". here's a recent transcript (the numbers preceding the bash

Two things: 1. I''m not convinced ''xm crash'' is needed - ''xm destroy'' will do this (and if you want a dump, do ''xm dump'' followed by ''xm destroy'') 2. I don''t see the point of the --noreboot option on ''xm dump'' -- I think this command should simply live-dump the specified domain - as

Hi, How can I get network info for domU similar to xm top & then ''N''.. I want to run a shell script to read this.. Thanks in advance, - regards Pallab _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Hi all I''m running CentOS 5.1 x64 + Xen 3.0 & I have setup a CentOS 5.1 x64 domU as a HMV. For the setup I used VNC, but I would prefer to be able to access it via "xm console cPanel" via SSH directly. Here''s the output cPanel HVM: [root@pc-00059 ~]# more /etc/xen/cPanel name = "cPanel" uuid = "ff940501-507d-04ca-e590-831e79ba0397" maxmem =

I got FC7 as dom0, I installed CentOS4.5 as domU using virt-install and it went fine.Installation was done using http. Now I am trying to reinstall it using xm command. below is my config file ############################# # -*- mode: python; -*- #============================================================================ # Python configuration setup for ''xm create''. # This

Hi, I don''t understand something about the vcpu-set function. My configuration: *memory = 2048 cpu = ''1-2'' maxvcpu = 4 vcpus = 1* When the DomU is running, and when i try to set 2 or 3 vpcu i get the error : xm vcpu-set domain_name 2 *Error: Cannot set vcpus greater than max vcpus on running domain Usage: xm vcpu-set <Domain> <vCPUs> Set the number of