similar to: Dummy ethernet device setup

Dear I need create second bridge xenbr1 for separate traffic between my virtual machine , I following this step but show message that Link veth0 is missing, how I can create veth0 ? When I run script for create xenbr1 ./network-bridge netdev=eth1 bridge=xenbr1 start Shwo this message Link veth0 is missing. This may be because you have reached the limit of the number of interfaces that the

Hi, This is my setting: I have a Logical Volume /dev/VG/suse with Suse installed. I have added it to the grub and I can boot it and works perfectly fine. Now I am running /dev/VG/root which is running Xen0. I have created a Xen config file to boot a VM with disk: /dev/VG/suse. In other words I want to boot /dev/VG/suse as a virtual machine. Below is what I am getting at boot time :

Hello, I am having a frustrating time trying to get bridge networking working. I''ve gone over the Wiki page on the topic, a few of the howtoforge pages and everything that I am doing is failing utterly. What I want to achieve is to have Dom0 be a stub running two DomUs. One DomU being a router/firewall and the other being the rest of what is on the current machine.

Ben Greear wrote: > Well, it seems we could and should fix veth to work, but it will have > to do equivalent work of copying an skb most likely, so either way > you'll probably get a big performance hit. Using the same pktgen script (i.e with clone=0) I see that a veth-->bridge-->veth configuration gives about 400K PPS forwarding performance where

Ben Greear wrote: > Well, it seems we could and should fix veth to work, but it will have > to do equivalent work of copying an skb most likely, so either way > you'll probably get a big performance hit. Using the same pktgen script (i.e with clone=0) I see that a veth-->bridge-->veth configuration gives about 400K PPS forwarding performance where

Hi, I have a strange problem with my networking setup. I read all forums around the world where people had similar problems, but couldn''t find a solution. I have an Attansic L1 gigeth chip on my mainboard. This chip works OK in stock Ubuntu Gutsy (development) 2.6.22-9-generic kernel. When I boot into Xen, and after the bridge is created, the network stops working. Some info: - If I

Hi, I''ve setup a box with xen. For the root machine, it''s ok, it see the network card: alian@yoda:~> /sbin/lspci ... 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 Gigabit Ethernet Controller (rev 19) alian@yoda:~> lsmod .... sk98lin 208748 1 alian@yoda:~> /sbin/ifconfig eth0 Lien encap:Ethernet HWaddr 00:15:F2:39:D4:DF

I installed Ubuntu Feisty successfully, then I configured the network (static IP) and things worked well. Then I installed Xen using "apt-get install ubuntu-xen-desktop". I could boot the xen kernel, and booted succesfully to dom0, however, there''s no network for dom0. According to network manager, I saw that Ubuntu recognizes now 4 unconfigured adapters (veth0, veth1, veth2,

I have a new x3655 IBM and whenever the /etc/xen/scripts/network-bridge script starts, the ethernet would no longer work. This post isn''t about the cause, but the fix. I did a lot of tcpdumps and Googling, but I''ll spare you that. All they do is prove that yes, there is an issue. :) I tried Debian 4.0 i386/amd64 and Ubuntu 7.04 Server i386/amd64 and they all exhibit the

Hello to all readers I've got a problem that I have to solve with wine and ghostscript. So, my only problem is that gostscripts (gswin32.exe) can't find the gs_init.ps file. I tried changes in the Registry, if there is a case sensitive mistake and every thing else, but it doesn't work. Now that I'm totally frustrated searching a solution on the web, this mailing list is my

Hello I use XEN 3.0 in debian sarge. I have a domU1 for routing and firewall. This domU1 use 2 network interfaces which is on a bridge ''gate'' and the other on bridge ''lan''. dumU2 use one interface (eth0) on bridge ''lan''. Then I make a ping out of domU2 to www.debian.de so I get no answer. The name isn''t resolved. A ping to IP of

Hi, I''m using Xen 3.0.3 on two servers with Debian Etch (amd64). These servers have 10 nics (2 onboard and 8 in two 4-port cards) so that every vm can have its own interface. This worked so far with the Xen Version from Etch with a wrapper script wich started 10 bridges at boot time. But now I''ve updated Xen on one of these server to Xen 3.2.0 from backports.org and now the

Hello everyone, I have been able to get windows xp to run under a virtual machine, but i cannot get any network access. My desktop is connected to a university network, and we are only given 1 ip address. so i understand i have to use routing instead of bridging, right? i have commented the two lines for bridge and enabled routing in /etc/xen/xend-config.sxp next i inserted a line: vif

Hi folks, I read quite some posts about "Destination host unreachable" problems before, but none could help me to solve my issue. So here we go: This is what I am using: SUSE Linux Enterprise Desktop 10 SP1 - Current with all updates Network configuration of my dom0: foobar:~ # ip a 1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd

Hello, Despite of reading a lot of descriptions I don''t understand the network configuration. I simply have too little experience. I work remote with the machine via ssh. My dom0 is running. I copied an existing installation into a LV and created the following file: # cat /etc/xen/domu-sarge # -*- mode: python; -*- kernel = "/boot/vmlinuz-2.6.18-4-xen-686" #kernel =

Hi, I got this error when starting a domU on Centos 5.1 i386, Device 0 (vif) could not be connected. Hotplug scripts not working. Why is this happening ? I should restart the machine to see if this still happends after a fresh network bridge. But it's somehow a production server, I would like not to restart it, if possible. No domU is currently running. I could start domUs a week ago.

Greetings! I finally got the install done for a couple of gust OSs (Win 2003 server & Suse Enterprise 10) Bothe gusts are up and running, but - no networking. My setup: Hardware - AMD Athlon 4200+, ABIT Motherboard, 4 GB of DDR2 RAM, 2 onboard GB NICs Host OS- Suse Linux Enterprise server 10 Xen - 3.0.2_09749-0.4 Config file for Win 2003 server guest: # -*- mode: python; -*-

Hi all, In a bridged setup, how we can set a large mtu(4k) for the interface on domU? Eventhough ''ifconfig eth4 mtu 4000'' command worked in my case, whether it reflect on the actual device? Moreover I can''t set mtu for the bridge as 4k. Setting any value above 1500 mtu shows the following error, xen-152:~ # ifconfig xenbr1 mtu 4000 SIOCSIFMTU: Invalid argument So

Hello, I have running xen over a debian server (debian sarge). Now I would like to configure a domU with redhat (AS 4), do you now any way to install it? -- Angel L. Mateo Martínez Sección de Telemática Área de Tecnologías de la Información _o) y las Comunicaciones Aplicadas (ATICA) / \\ http://www.um.es/atica _(___V Tfo: 968367590 Fax: 968398337

I recently upgraded "libvirt" on Gentoo to 1.2.2-r1 (latest available). I have not used LXC containers for a few weeks, so I don't recall what version of libvirt I was using when my container last booted successfully. Unfortunately, Gentoo's portage tree does not offer any previous versions of libvirt that I could downgrade to. TL;DR: My container is configured to use