similar to: Question about assigning NICS

Hello, I''m new to Xen (and this mailing-list) and facing some problems with the network. I''m stuck and don''t know how to continue. And Google isn''t very helpful either... My setup: - Ubuntu 7.10 for dom0 and Debian 4.0 for all domU - 4 physical NIC (DHCP from my ISP, internal LAN, DMZ & WLAN) - 1 Dom as firewall/router - 1 domU with internal services

So Working on CEntOS 5 I am trying to sett up Xen with 2 bridges, one that connects dom0 and most of the domU to the physical card and the out to the network. Got that figured out no problem, now i want to have a second bridge that runs a local network for all the doms that doesn''t connect to the network. With code I have found used in multiple places I can easily get 2 bridges, and

Hello all, I have been running xen for a while now with two interfaces: dummy0 for host only communication, and eth0 for the outside network. my script looks like this: (/etc/xen/scripts/network-bridge-more) ------------------------------------------------------------------ #! /bin/sh dir=$(dirname "$0") "$dir/network-bridge" "$@" vifnum=0 netdev=dummy0

I have a beefy machine (Intel dual-quad core, 16GB memory 2 x GigE) I have loaded RHEL5.1-xen on the hardware and have created two logical systems: 4 cpus, 7.5 GB memory 1 x Gige Following RHEL guidelines, I have it set up so that eth0->xenbr0 and eth1->xenbr1 Each of the two RHEL5.1 guests uses one of the interfaces and this is verified at the switch by seeing the unique MAC addresses.

Hello, I created a CentOS 5.0 x86_64 guest under Debian Etch with Xen 3.0.3 and it boots fine except for one re-occuring problem - whenever it boots the /etc/sysconfig/network-scripts/ifcfg-eth0 script gets renamed to .bak and doesn''t configure the ethernet device. Here is the content of this file: TYPE=Ethernet DEVICE=eth0 BOOTPROTO=static ONBOOT=yes IPADDR=192.168.0.247

Hi, I''ve a working xen 3.0.2 booting a gentoo linux on Dom0. I have setup a Windows XP in a DomU OK with no problems except the network!! My problem is that I wanted to give a working network interface on the DomU and the best I could. making the windows detect an network adapter, was putting: vif = [''type=ioemu''] I also tryied: vif = [''type=ioemu,

I have a Xen DomU configuration that was made in the days before libvirt and virt-install. In this configuration I have: vif = [ ''mac=00:16:3e:05:06:01, bridge=xenbr0'', ''mac=00:16:3e:05:06:0a, bridge=xenbr1'' ] and then in xend-config.sxp I define (network-script my-network-bridge) where my-network-bridge is in the scripts directory and looks like this:

Hi. I am running Xen 3.0.3-1 on Debian Etch. Does anyone have a sample config file for creating a windows DomU? I have the ISO file from my windows CD. I''m not using LVM Thanks in Advance _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Hello, I am having big problems with Xen virtual network interfaces. First I tried typical bridge support, no luck. The packets sent from dom0 to domU seemed to disappear somewhere. Then, to debug the problem I have set up a simple point-to-point link and still have the same problem. I am using Xen 3.0.4-1 and Linux 2.6.16.x in both dom0 and domU. I have tried kernel 2.6.16.35 and 2.6.16.41. I

I added a virtual interface eth0:1 on one of my machines and suddenly networking breaks on startup of the system (eth0 is gone) when xend starts and runs the network-bridge script. This is supposed to be fixed according to: https://bugzilla.redhat.com/show_bug.cgi I checked and the network-bridge script contains this fix. It works fine on one of my PCs when eth0:1 is added, but not on this

hi all i am trying to boot from rhel5.1 x86_64 image. with the following configuration kernel = "/usr/lib/xen/boot/hvmloader" builder=''hvm'' memory = 3048 name = "rhel51" vcpus=1 cpus = "" vif = [ ''type=ioemu, bridge=xenbr0'' ] disk = [ ''phy:/dev/cciss/c0d0p7,ioemu:hda,w'',

Hi, [1] Are there guides for setting up a virtual switch for use in between guest domains in Xen ? [2] In Xen, is it possible for a guest domain to perform a initial dhcp IP lookup from another guest domain ? How are the configurations like ? Are there references or step procedures ? Kindly advice. Thanks. _______________________________________________ Xen-users mailing list

Sorry for my ignorance but....I''ve installed a debian lenny dom0 with a xen kernel, then I''ve configured two domX. I''ve noticed that there isn''t a kernel installed for these ones. I run aptitude to update packages, I''ve updatede the dom0 kernel but....the others? _______________________________________________ Xen-users mailing list

Hello again, folks! I''m getting one strange problem with FC5 running on XEN 3.0.3 x64... The MRTG point to my machine with XEN running one absurd volume of output data sent (normal is around 6 MB/s) and when XEN is working we get 80 MB/s until my DRAC is alive... after this, the machine crash, DRAC stop do reply, swith stop do work together... Anyone knows whats happening now? ;)

Hey folks, I created a DomU, installed Linux, and then realized I''d only given it 1 NIC so brought it down to edit the cfg file to give it another NIC. Originally I just had : vif = [''''] And so I guess the defaults worked for the 1 NIC. So I changed it to : vif =

Hi, I''m using Xen 3.0.3 on two servers with Debian Etch (amd64). These servers have 10 nics (2 onboard and 8 in two 4-port cards) so that every vm can have its own interface. This worked so far with the Xen Version from Etch with a wrapper script wich started 10 bridges at boot time. But now I''ve updated Xen on one of these server to Xen 3.2.0 from backports.org and now the

Hi *.*, This is a continuation on the 2 NICs thread after some more testing. Just to remember my goal. --------------------------- I want to create a domU with 2 virtual NICS. One of them will contact the outside world, the other one will contact a VPN. No reason in concrete for choosing the bridging protocol, only because its the default one. I installed the dom0 with the 2 NICs active, with

I have 3 machines, T60 thinkpad with e1000 NIC Dell PowerEdge 2950 with bnx2 NIC HP DL360 G4P with tg3 NIC All running xen 3.03 / 2.6.16.29-xen I have a netbootable image with 2.6.16.29-xenU. This image when it boots creates a vlan eth0.4002, and then tries to communicate on that interface to a central server. On the machines with e1000 an bnx2 NICs, this works fine. On the

Hi, I''m trying to set up networking on a new machine. I''m not getting any networking from the domU''s I notice that I have two bridges being created: xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:3024 errors:0 dropped:0

I'm seeing an issue with xend not running a custom network script automatically, but works when I run it manually. In /etc/xen/xend-config.sxp I've changed: (network-script network-bridge) TO: (network-script network-custom) Here is /etc/xen/scripts/network-custom: # !/bin/bash # network-custom script=/etc/xen/scripts/network-bridge case $1 in start) $script start vifnum=0