similar to: Xen and Ndiswrapper with Athereos chipset

Hi Folks, I am trying to get my wireless network card work under dom0 of XEN. I could successfully install the ndiswrapper drivers and could see it being associated to AP. However I amn''t able to transmit any packets outbound. I could''nt even ping the AP. Interestingly when I run a tcpdump I can see few broadcast packets on the interface. There no rules in iptables for nat or

Hi - I'm trying to get wireless running on CentOS 4.7 on a dual core laptop (latitude-e4500) for an employee. I'm having trouble with building dkms-ndiswraper-1.54-1.el4.rf - enclosed are the errors messages. The kernel was rebuilt to disable CONFIG_4KSTACKS. The errors prior to rebuilding the kernel are identical to the errors after rebuilding the kernel and rebooting - minus the error

Hello all, Has anyone gotten dom0 to work with ndiswrapper? I''m a newbie, but I''ve managed to install dom0 and get it to boot, then compile a new dom0 and get that to boot too. I''ve turned on the appropriate .config params for wireless (as far as I know). I''ve downloaded/compiled/installed the latest ndiswrapper. When I ''modprobe

Hi Folks, I'm trying tio install WLAN - USB - Stick Netgear WG111v3. ndiswrapper -i wg111v3 works. I can see ndiswrapper -l wg111v3: driver installed device (0846:4260) present But after modprobe ndiswrapper the system freezes. Troublshooting on ndiswrapper-sites says: It's a problem of "kernel is using 4K stacks (CONFIG_4KSTACKS)" Solution: recompile the kernel.

This is an abbreviated version of an e-mail that I also posted to the ndiswrapper mailing list. Compressing the long story, I ran into the same problem using CentOS 5 as I had with Fedora Core 6 and ndiswrapper: my laptop (HP Pavilion zv6000 series with a Broadcom BCM43xx wireless NIC) would lock up or spontaneously reboot after a few hours if I brought up the wireless interface. I also

I know, I know... don't use the non-standard kernels unless you have to... BUT: I have a D-Link N150 USB card. Bus 001 Device 004: ID 0846:9030 NetGear, Inc. WNA1100 Wireless-N 150 [Atheros AR9271] This isn't supported in C5, but it is supported in newer kernels (ath9k_htc). So let's try NDISwrapper: # rpm -i kmod\-ndiswrapper\-1.56\-1.el5.elrepo.i686.rpm

Hello, I had installed CentOS 5.0 on my desktop PC having a Realtek 8180L based PCI wireless card. Since the drivers for this chip are not available in the kernel, I created RPMs for ndiswrapper-1.43 from the source code and installed them. I could configure the wireless card and use it but invariably the system freezes after sometime. No such thing happens if the wireless card is disabled. In

Hi everyone! :-) I have a problem with making a wireless USB dongle work under CentOS 6. The dongle is known to not work natively under Linux and last time I used it (cca 3 years ago) I managed to get it working using ndiswrapper. This time I was hoping to make it work again in the same way. But the "yum install kmod-ndiswrapper" reports the following (among other regular stuff):

Greetings: I'm just installed Centos-4 on an IBM T-21 laptop. So far so good. Now I'd like to pop in a wireless lan adapter. I'm looking at a buying a Linksys WPC54G adapter (although I haven't done so yet). After doing some searching, it looks like the best way to get this card working is via ndiswrapper [http://ndiswrapper.sourceforge.net] and then to use Windoze

Hi people, I am using CentOs 4.3 and i'm trying to use ndiswrapper, but i don't obtain make it to run. my problem is with "invalid format" of module ? any suggestions ? thanks.

WPA-2 (WPA Enterprise) fails with the new kernel(s) using ndiswrapper and wpa_supplicant. I haven't tried other authentication modes because that entails changes in the wireless setup which I am loathe to make right now. (It's a Broadcom mini pci card, so I have to use ndiswrapper with this Dell laptop. Bummer!). Rebuilding the newest wpa_supplicant rpm from the FC5 source rpm's

I ALMOST bought a dongle on sale at ecost without checking. There is a driver for the CP Technologies adapter, but not as an rpm, it seems. Madwifi.org says no USB support. Though there is some discussion of using the ndiswrapper driver. So which to use? Anyone out there with any success?

Processing commands for control at bugs.debian.org: > user debian-qa at lists.debian.org Setting user to debian-qa at lists.debian.org (was anbe at debian.org). > tags 714794 - moreinfo Bug #714794 {Done: Gilles Filippini <pini at debian.org>} [release.debian.org] pu: package sikuli/1.0~x~rc3.tesseract3-dfsg1-5+deb7u1 Removed tag(s) moreinfo. > tags 710035 - moreinfo Bug #710035

Hey guys, I'm having trouble with PRIx64 and buddies in the X86 target on SLES 11. After searching, my issue seems like a generic problem with PRI support on different OS's. Here's a decent description of my problem: http://gcc.gnu.org/ml/gcc-help/2006-10/msg00221.html Any suggested methods to correct for <inttypes.h> not having the proper macros defined (besides defining

I have a question - if a user calls up w/ blocked caller id I get the following on my phone Incoming call from asterisk This is the same on my Cisco 7940s and Polycom phones. For average users this is not intuitive at all.. I'd like to configure this so if I deploy this at a customer site it says "caller id unavialable". With the spelling done right.... Any ideas on how this

Hi guys, Is there any problem with www.centos.org? It seems down for me, was trying since last two weeks. -- Syam G Krishnan GPG 4096R/FBB26E60 Red Hat India Pvt Ltd

Hello everyone, I would really like to get wireless working on my CentOS 5.1 install. I have a LinkSys WPC54G (I guess version 1 since no version is listed) but everything I've read indicates that this would be a nightmare for a Linux newbie like myself. I got as far as NDISWrapper, but right off the bat I am getting issues with KBuild and I guess my kernel source so I can't even get

http://bugzilla.mindrot.org/show_bug.cgi?id=83 Summary: fork() fails when there are PAM limits set Product: Portable OpenSSH Version: 3.0.2p1 Platform: ix86 OS/Version: Linux Status: NEW Severity: normal Priority: P2 Component: sshd AssignedTo: openssh-unix-dev at mindrot.org ReportedBy:

Hi Folks, I'd like to install my USB-WLAN-Stick Netgear WG111v3. Ndiswrapper works correct after installing Kernel-Modules from atrpm ndiswrapper-kmdl-2.6.18-53.1.19.el5.centos.plus-1.52-16.el5.i686.rpm. But by calling wpa_supplicant with wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf -d machine freezes. My wpa_supplicant.conf:

Hello. For couple of days ago i was searching google for some howto on installing Centos 5.3 on HP 2133 but i didnt found any. Since i have managed to install it on my HP 2133 i wrote on howto as well. I just need 2 things to be changed / defined better and its installing ndiswrapper (wich i did but im not so sure that i took right .rpms but it works), and second one is Installing 7zip on centos