similar to: Ether bonding with Xen

Hi list When I create a domU the network isn''t reachable when it''s loaded. Only if I do a xm console domUname and do some sort of network activity like pinging an outside host or traceroute. First then there''s network connection from the outside to services like webserver etc. What can cause this? I''m using Xen 2.0.5 stable domU from binary dist and

Following Luke''s very successful Puppet talk at GLLUG in London, which was so over-subscribed there were people queueing outside and pressing their little faces up against the glass, I wonder if the market will bear a London Puppet meet? If there are more than two or three people interested it might be worth arranging something, perhaps a pub session where we can talk about what

In 2.4 there used to be a megaide driver for certain ata raid controllers. In 2.6 I can't access more than my /dev/hda , I can see my other 4, I can create filesystems on them, but I can't mount them Anyone knows how to use these on a 2.6 kernel (Centos 4.2) greetings Kris 00:02.0 RAID bus controller: Silicon Image, Inc. SiI 0649 Ultra ATA/100 PCI to ATA Host Controller (rev 02)

I've just setup nic bonding on our server (DL585-G7 running Centos 5.5 x86_64) as detailed on the wiki: http://wiki.centos.org/TipsAndTricks/BondingInterfaces and all seems fine but from other "howto's" I've seen on the web, they're should be a /proc/net/bond0/info As far as I can see, I don't have one and I'm not sure if it should be there or its absence is a

I use bonding under CENTOS4.5 x32_62. I have these weird messages when I'm restarting network. Do you have any ideas how to fix this? (there is similar bug for centos5 http://bugs.centos.org/view.php?id=2404, but the author says that it worked for him in centos4...) Thanks Vitaly Dec 17 08:34:21 3_10 kernel: bonding: Warning: the permanent HWaddr of eth0 - 00:1A:64:0A:DC:9C - is still in

Hi, I've using linux bonding in active-backup mode to combine two pairs of GigE NICs (eth0/eth1, eth2/eth3) into two logical bonds (bond0/bond1). All is working fine. However, I would like to specify a primary interface for each bond. This means I need to specify different options to the bonding module for each bond. I have tried every conceivable incantation of options and cannot get the

Hi all, Since it looks like I''ll be attending FOSDEM, I now need to find some lodging, and if possible I''d like to line up a presentation or four. Someone in the community offered to let me crash with them if I came to the conference (someone with the nick of ''robk'' on IRC, I think), so I''d like to take that person up on it if possible.

Is there a procedure/howto to follow when moving from existing HW to virtual machine. I found: http://wiki.centos.org/HowTos/Xen/MoveNative2DomU but it seems little bit complex for me(but not impossible). Is there a tool that does the migration (XenOptimizer should do it???) When searching I find only commercial tools... -----------------------------------------------------------------

Hi, does anyone know where to get a howto or pre configured Centos working as guest in XEN ? thnaks and best regards Niels -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.centos.org/pipermail/centos/attachments/20051114/f2bedd85/attachment.html>

Hi, I'm trying to configure a network bridge over a bonding without any success. Here is my configuration: ifcfg-eth0: DEVICE=eth0 HWADDR=00:1E:C9:E8:3F:E5 ONBOOT=yes USERCTL=no MASTER=bond0 SLAVE=yes ifcfg-eth1: DEVICE=eth1 HWADDR=00:1E:C9:E8:3F:E7 ONBOOT=yes USERCTL=no MASTER=bond0 SLAVE=yes ifcfg-bond0: DEVICE=bond0 ONBOOT=yes BRIDGE=br0 USERCTL=no ifcfg-bridge0: DEVICE=br0

HI All. I have a linux box connected to a switch network with 2 network interfaces, how would I able to ''trunk'' these 2 interfaces? options I can see are: - ethernet bonding - iproute2? - teql Which one are the best to use? I''m curretly having problem with ethernet bonding, my setup are as follow: ip add: 192.168.10.30/24 I do: # modprobe bonding # ip addr add

Dear All, Please ignore my previous mail I have using CentOS 4.4 Linux and Kernel Version is 2.6.9-42.EL I have configured Cluster Suite with 2 servers Server 1 : 192.168.13.110 IP Address and hostname is primary Server 2 : 192.168.13.179 IP Address and hostname is secondary Floating : 192.168.13.83 IP Address (Assumed by currently active server) I have configured Ethernet Channel Bonding in

Hi, I am currently struggling with the right way to configure a bonding device via kickstart (via PXE). I am installing servers which have "eno" network interfaces. Instead of the expected bonding device with two active slaves (bonding mode is balance-alb), I get a bonding device with only one active slave and an independent, non-bonded network device. Also the bonding device

With the current talk on bonding, I have a few questions of my own. I'm setting up a KVM host with CentOS 6.3 x86_64 on which I'd like to attach the VMs to a bonded interface. My target setup is one where two GigE NICs are bonded and then the KVM bridge interface is attached to the bonded interface. Initially I tried to use the balance-alb mode (mode6), but had little luck (receiving

I four nodes setup to do active-backup bonding and the drivers loaded for the bonded network interfaces vary between tg3 and e100. All interfaces with the e100 driver loaded report errors much like what you see here: bonding: bond0: link status definitely down for interface eth2, disabling it e100: eth2: e100_watchdog: link up, 100Mbps, full-duplex bonding: bond0: link status definitely up for

Hello list, Please don''t shoot me. I know I''m doing something with bonding that bonding wasn''t made for. I just want to give it a try. I want a simple mechanism to have a failover on a 24Mbit line to a 2Mbit line in case the 24Mbit line goes down. Between A and B there are two lines: a 24Mbit and a 2Mbit. I use two OpenVPN tunnels with tap devices: +-- tap0 (A)---

Hi guys, I am trying to get bonding work on a debian etch system. I searched already in the mailing list but unfortunately I couldnt find a proper solution. This is what i did so far. - Installed Debian Etch on my server - Installed the following packages for using Xen from the Debian repository: xen-hypervisor-3.0.3-1-i386-pae linux-image-2.6.18-5-xen-686 linux-image-2.6.18-5-xen-686 xen-tools

CentOS 6.2......... Why do the physical interfaces report (correctly) that they're negotiated at 1000Mb/s, but when I `cat /proc/net/bonding/bond0` I get 100Mbps for the member interfaces, and when I ` mii-tool bond0` I get 10Mbps for the bond? ----------------------------------------------------------------------------------------- ethtool em1 Settings for em1: Supported ports: [

Hi all, Someone played with kickstart bonding with centos 6.4 ? CentOS 6.4, as upstream now support ifcae bonding in kickstart network section. I've an issue with configuring a second bonding iface in kicstart on CentOS 6.4. The first bonding (bond0) works as espected but the second is not configured during installation. I've a 6 nic server (two for "puclic" network, two for

Hello I have two linux machines connected via 2 dsl lines (bonded) 192.168.0.1-eth0-dsl---2Mbit---dsl-eth0-192.168.0.2 ^-eth1-dsl---2Mbit---dsl-eth1-^ so the final figure is something like this: 192.168.0.1-bond0---4Mbit---bond0-192.168.0.2 I can only use arp monitoring for fail checking - if one dsl line fails - automatically use only the other one. I set up everything correctly (i