similar to: [Bug 589] New: MARK doesn't work properly with incoming traffic

I have an Everex laptop (ick, but it was super cheap) that has an Atheros wireless NIC in it, but I can't seem to get it to connect to my wireless in-home LAN. Here's what I've done so far (that isn't working) - any suggestions? [root at marktop mark]# lspci | grep Ether 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 7c) 05:01.0 Ethernet controller:

I''m trying to follow Chapter 10 of the howto and apply it to two ubuntu machines each with two 802.11b/g interfaces. However, I cannot get a connection. I would like the 4 interfaces to create 2 ad hoc links on separate channels. I have set this up successfully with the following: /etc/dbus-1/event.d/25NetworkManager stop wlanconfig ath0 destroy wlanconfig ath0 create wlandev wifi0

I would like to route ssh in my network via DSL2 and all other trafic via DSL1. So far I menaged to do it for LAN2 but there are still WLAN1,LAN3 and LAN1 to go. On all routers I added table "pilicka" with rule for fwmark and I fwmarked ssh. # ip rule show 0: from all lookup local 32765: from all fwmark 0x3 lookup pilicka 32766: from all lookup main 32767: from all lookup

I know, I know... don't use the non-standard kernels unless you have to... BUT: I have a D-Link N150 USB card. Bus 001 Device 004: ID 0846:9030 NetGear, Inc. WNA1100 Wireless-N 150 [Atheros AR9271] This isn't supported in C5, but it is supported in newer kernels (ath9k_htc). So let's try NDISwrapper: # rpm -i kmod\-ndiswrapper\-1.56\-1.el5.elrepo.i686.rpm

hi all, this is my first hit on the mailing list. hope i m posting in the right place. well, i have a dell vostro 1510 laptop with broadcom wifi adapter. n it doesnt work! :( i installed the wifi drivers with ndiswrapper. iwconfig shows the following. [root at laptop ~]# iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. wlan0

Hopefully this is a simple answer. I am new to setting up bridges on a linux system. Here is what I have set up: Laptop directly connected to the eth0 port on the bridge (A Soekris 4521 board). The otherside of the bridge is a wirelass lan card (SMC2532b-w) as wlan0. The wlan0 is setup in managed mode to communicate to my test ap2000. When I do a 'brctl showmacs br0' on the

I'm having a wireless connection issue with an HP laptop and a Zotac media server after the 6.4 package updates from CR repository. Nothing changed with wireless config as far as I can tell. Both have been working fine with previous releases of 6.x. Oddly, if a cat 5 cable is connected for a few seconds and then disconnected the wireless works fine and survives a 'service network

I am having problem in ping or connect AP from Mobile Node(essid & channel is the same,maybe routing did not set properly but i fail to configure with route add default gw 192.168.3.4,its alway said network is unreachable ),My Mobile Node is using acx100 as driver while AP(redhat 9.0) is using HOSTAP 0.1.3.Any one can help? I heard How-To said we not need to set address on eth0 & wlan0

[desktop] ----- lan ----eth0 [notebook] eth1 192.168.?.? ` ----- wlan ---- [speedport(hub and router)] -- internet 192.168.2.x So on my laptop I have eth0 beeing lan, eth1 beeing wlan ethernet card. When only using eth0/1 everything is fine. Now I want to be able to use internet from both [desktop] and [notebook]. Typically you set up a bridge with

Hi, I have a laptop DELL M90 with an Intel PRO/Wireless 3945ABG card. I'm using centOS 5.1 kernel 2.6.18-53 i386. I installed ndiswrapper v 1.52 I installed the driver http://ftp.us.dell.com/network/R164255.EXE The wireless-tools is v 28.2 When I trying to connect to my wireless access point with encryption key disabled everything work fine !!!! When I enabled the encryption key on my

Folks Is there a way in CENTOS6 to define and turn on wireless from the command line. My environment is as follows: I'm trying to build a laptop for travel, and have KVM-guests for both Linux Gui and Windows, using internal NAT networking. The underlying host machine doesn't really need to be much more than a NAT provider, and the usual command-line utilities. When I arrive at a

Hi, I am trying to get my kickstart file that worked under 5.1 to work under 5.2 centos x86_64. This is the error that I get. On the screen it says Exception occured and gives me the option to save it. This is that file. I dont see any odd that would cause it to crash. Can anyone help. My kickstart file is in the mix below. Seems to be related to network, my line seems fine (I think) for

Hello, I''m on Debian Sarge, and try actually to setup iproute this way : - local network 1: 192.168.12.0/24 - local network 2: 172.20.0.0/16 - one router on both network : 192.168.12.50 & 172.20.201.50 - one router to internet (SLIS) : 172.20.1.1 I want from my 1st local network to access internet... here are my lines... (taken from The LARTC Howto) ip route add 172.20.0.0/16 dev

Hi, i''m trying to use PCI passthrough feature on Xen 4.0 but it fails on my Wireless card. I use Xen 4.0 on a Debian 6.0 (package from repo) and try to passthrough the following PCI device root@omega:~# dpkg -l | grep xen ii libxenstore3.0 4.0.1-1 Xenstore communications library for Xen ii linux-image-2.6.32-5-xen-amd64 2.6.32-30 Linux 2.6.32 for 64-bit PCs, Xen dom0 support ii

Hello, In one of our project we need to connect one IMX 27 based baord which ahs a internal FEC controller & an MPC 8323RDb baord which has a Built in Network controller. We need to connect the IMX27 based board to MPC board thro cross cable & MPC baord has wlan AP card . Basically we want to communicate from IMX27 to wireless network. Hence we are planning to make follwoing arranage

 Hello, everybody.  This one''s got me stumped.  What I''m trying to do is have two networks--192.168.1.0 and 192.168.2.0--with SMB and WINS running between them.  So far I can mount SMB shares allright, but I can''t browse by WINS names across the router.  I''ve posted this question on Linuxquestions.org; you''ll find the details there.  Here are my

Hello All, ?I have a Dell Vostro 1550 laptop. i3 core, 64 bit, 8gb ram etc etc. I had a nic interface, but some how the wired nic is not working. So I am trying to use the BCM 4313 wireless chip, of this system, to connect to the internet. ?I have Cent os 6.5 (64 bit) installed with the required libraries and kernel sources, headers etc. I got the source code of the driver,

On Sun, Jan 31, 2016 at 8:56 AM, Michal Privoznik <mprivozn@redhat.com> wrote: > On 29.01.2016 11:24, Andrei Perietanu wrote: > > Hi all, > > > > I am using libvirt to manage VM on my system; after creating a VM > (default > > no NICs are present in the configuration) you can add any number of > > interfaces to it (as long as they exist on the host).

Hi all, I am using libvirt to manage VM on my system; after creating a VM (default no NICs are present in the configuration) you can add any number of interfaces to it (as long as they exist on the host). To do that, I edit the configuration xlm: vmXml = self.domain.XMLDesc() root = ET.fromstring(vmXml) devices = root.find('./devices') intf =

On 29.01.2016 11:24, Andrei Perietanu wrote: > Hi all, > > I am using libvirt to manage VM on my system; after creating a VM (default > no NICs are present in the configuration) you can add any number of > interfaces to it (as long as they exist on the host). > To do that, I edit the configuration xlm: > > vmXml = self.domain.XMLDesc() > root =