similar to: Updated How to Setup a Software RAID on CentOS 5

Hi, When I perform a software RAID 1 or RAID 5 installation on a LAN server with several hard disks, I wonder if GRUB already gets installed on each individual MBR, or if I have to do that manually. On CentOS 5.x and 6.x, this had to be done like this: # grub grub> device (hd0) /dev/sda grub> device (hd1) /dev/sdb grub> root (hd0,0) grub> setup (hd0) grub> root (hd1,0) grub>

http://wiki.centos.org/HowTos/SoftwareRAIDonCentOS5 Comments and corrections please.

I have a system that is RAID -1 configured as /dev/md0 is /dev/hda1 /dev/hdb1 /dev/md1 is /dev/hdb3 /dev/hdb3 it seems as though /dev/hda has failed.... I have another disk (identical model) that I can replace hda with. I know about the commands fdisk to repartion and raidhotadd /dev/md0 /dev/hda1 and raidhotadd /dev/md1 /dev/hda3 (to be ran after the system boots). BUT... how do I now get

I have a CentOS 4.2 system that was set up VERY quickly following the demise of its former life as a CentOS 3 server - you don't want the full story, but it had to be done quickly to get a company up and working following a slight disaster involving an electrician, a portable appliance safety tester and a pulled power cable - anyway, here's where I am at... Everything is running fine but

I have Windows 7 on /dev/sda and CentOS 6.4 on /dev/sdb. Here are the layouts: (parted) select /dev/sda Using /dev/sda (parted) print Model: ATA WDC WD10EZEX-00Z (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/4096B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 374MB 373MB primary ntfs boot

Hi all, I've installed CentOS 4.4 in a box which previously had dual boot (XP SP2 and Ubuntu) I can run CentOS without problem but I can't boot XP SP2. When I try it the system simply hangs... [root at seth ~]# fdisk -l Disco /dev/hdb: 40.0 GB, 40020664320 bytes 255 cabezas, 63 sectores/pista, 4865 cilindros Unidades = cilindros de 16065 * 512 = 8225280 bytes Disposit. Boot Start

Hi All, I'm currently trying to install centos 5.4 x86-64bit on a raid 1, so if one the 2 disks fails the server will still be available. i installed grub on /dev/sda using the advanced grub configuration option during the install. after the install is done i boot in linux rescue mode , chroot the filesystem and copy grub to both drives using: grub>root (hd0,0) grub>setup (hd0)

On 8/5/2015 1:00 PM, Chris Murphy wrote: > On Wed, Aug 5, 2015 at 10:52 AM, Bowie Bailey <Bowie_Bailey at buc.com> wrote: >> How would I go about pointing it at the partition? >> >> What I am currently doing is this: >> device (hd0) /dev/hdg >> root (hd0,0) >> setup (hd0) > > setup (hd1,0) > > It's hd1 if your device map is correct and

On 8/5/2015 12:34 PM, Chris Murphy wrote: > On Wed, Aug 5, 2015 at 9:12 AM, Bowie Bailey <Bowie_Bailey at buc.com> wrote: >> I am trying to upgrade my system from 500GB drives to 1TB. > I'm going to guess that there are no IDE drives that have 4096 byte > physical sectors, but it's worth confirming you don't have such a > drive because the current partition

I have a p4 motherboard with 2 ide interfaces, I connect 2 40 GB drives as hda and hdc, I install Centos 4 from a CDROM, and partition the drives as 2 x raid partition each plus a swap partition on hda, the make md0 and md1 to install /boot and / respectively. Install goes well, everything looks great, go to reboot from drives, and all I get is "grub" but no boot. I have tried this ten

I must have really shot myself in the foot on this one. I reinstalled CentOS 4.4 (have to, for now) on my test machine, exactly the way it was before (same options anyway), but when it comes up, I get: Booting 'CentOS-4 x86_64 (2.6.9-42.ELsmp)' root(hd1,0) Filesystem type is ext2fs, partition type 0x83 kernel /vmlinuz-2.6.9-42.ELsmp ro root=LABEL=/ rhgb quiet Error 15: File not

Hi all, I'm trying to setup a RAID-1 with Centos4.2 on HP Netserver E60. The raid consists of 2 9,1GB SCSI disks. The partitioning and installation process went smoothly, but after it finished and rebooting, there is an error: Missing operating system. The partition is: / /home swap Bootloader is on device md0. What could be possibly wrong? Thank you, -- Fajar Priyanto | Reg'd Linux

I have been trying to multiboot centos 4.1 and the current solaris express build 15. I have two hard drive s, the first one ( hd0 ) devoted to CentOS 4.1 and windows xp (no problems). The second drive (hd1) for Solaris 10 only. I tried to boot solaris from CentOS grub and got the following error messages: Booting Solaris 10 root(hd1,0) Filesystem type unknown, partition type 0Xbf kernel

Greetings ... Been lurking on the list for some time, hoping that at some point, I might be able to add to the collective (Yes, way to much StarTrek in the background! ) ... I have learn quite a bit by just lurking, but now I think I might have something to add ... I'm not sure the exact protocol or procedure for this and it's late in the evening and would like get this out, before I

Hello, I have two disks sda and sdb. One of the was broken so I have changed the broken disk with a working one. I started the server in rescue mode, and created the partional table, and added all the partitions to the software raid. *I have added the partitions to the RAID, and reboot.* # mdadm /dev/md0 --add /dev/sdb1 # mdadm /dev/md1 --add /dev/sdb2 # mdadm /dev/md2 --add /dev/sdb3 # mdadm

Trying a different approch. Senario Raid 1 setup Bootable raid drive failed Mirror has been working for almost a month and then rebooted Now can't boot mirror drive grub not mirrored from other drive. I Fixed bootable drive. Question? Can I hook up both drives and boot fixed drive then rebuilt mirror from nonbootable drive to bootable drive? Does the raid automatically rebuilt when I

CentOS Community, I have a dedicated server with 4 hard drives in a RAID 10 software configuration running LVM. My OS is CentOS 6.2. Earlier today, I rebooted my system and my system did not come back online. I opened a ticket with my datacenter who informed me that one of my hard drives is no longer recognized by the bios and has failed. I was told that an OS reinstall was needed. I

Hi, I'm installing CentOS 4.4 64 bits with RAID 1 per software. But when the installation finishes, i cannot boot the system. I always get GRUB error 15. Any ideas ? Thanks in advance. Warm Regards, M?rio Gamito -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.centos.org/pipermail/centos/attachments/20070228/9c237e08/attachment.html>

Does documentation exist describing how to convert a simple, single disk non-RAID CentOS 5 system to software RAID1 using the CentOS install CD/DVD as a rescue disk? (Assuming not) Is there a need for such? (Assuming need) I volunteer to produce it. -------------------- Ed Heron

So, it installed happily. Then wouldn't boot. No problem, I'll bring it up with pxe, then chroot and grub2-install. Um, nope. I edited the device map from hd0 and hd1 being the RAID to /dev/sda and /dev/sdb, then ran grup2-install. It now tells me can't identify the filesystem on hd0, and can't perform a safety check, and gives up. What am I missing? Google is not giving me any