similar to: extend raid volume - new drive

greetings. centos 6.7 [current] 'disk utility' has started showing message; WARNING: The partition is misaligned by 2560 bytes. This may result in very poor performance. Repartitioning is suggested. for sdc5 - /home partition. /dev/sdc5 302243312 156348604 130534968 55% /home /dev/sdc7 80854912 57088 76683952 1% /hdd/c/07 other than time involved to backup

I have a system with 4 disk drives, two 512 Gb and two 1 Tb. It look like this: CentOS release 5.9 (Final) Disk /dev/sda: 500.1 GB, 500107862016 bytes Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes Disk /dev/sdc: 500.1 GB, 500107862016 bytes Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes ================================================================= Disk /dev/sda: 500.1 GB, 500107862016 bytes

I am trying to upgrade my system from 500GB drives to 1TB. I was able to partition and sync the raid devices, but I cannot get the new drive to boot. This is an old system with only IDE ports. There is an added Highpoint raid card which is used only for the two extra IDE ports. I have upgraded it with a 1TB SATA drive and an IDE-SATA adapter. I did not have any problems with the system

Aaaaaa, I'm pulling out my hair over here! I have an external USB drive which I had at work, connected just fine to my CentOS 5.3 box. I recall there was some jiggery-pokery involved, but do not recall just what. So now I'm on my wife's freshly installed CentOS 5.3 laptop trying to get it going, and I keep getting errors about FATAL: Module fuse not found. I saw this message from

Hi, I'm trying to disconnect some iSCSI targets, but can't seem to. [root at localhost ~]# iscsiadm -m session tcp: [1] 192.168.2.202:3260,1 iqn.2011.01.22.freenas.nvr:500gb tcp: [3] 192.168.2.200:3260,1 iqn.2011-2.za.co.securehosting:RAID.thin3.vg0.1tba tcp: [4] 192.168.2.202:3260,1 iqn.2011.01.22.freenas.nvr:extent0 tcp: [5] 192.168.2.200:3260,1

Hi All, I'm currently trying to install centos 5.4 x86-64bit on a raid 1, so if one the 2 disks fails the server will still be available. i installed grub on /dev/sda using the advanced grub configuration option during the install. after the install is done i boot in linux rescue mode , chroot the filesystem and copy grub to both drives using: grub>root (hd0,0) grub>setup (hd0)

Hello all, I have 2 x 250GB sata disks (sda and sdb). # fdisk -l /dev/sda Disk /dev/sda: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 14939 119997486 fd Linux raid autodetect /dev/sda2 14940 29878

I am planning to increase the disk space on my desktop system. It is running CentOS 5.9 w/XEN. I have two 160Gig 2.5" laptop (2.5") SATA drives in two slots of a 4-slot hot swap bay configured like this: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End

Hi, I'm currently experimenting with software RAID1 on a spare PC with two 40 GB hard disks. Normally, on a desktop PC with only one hard disk, I have a very simple partitioning scheme like this : /dev/hda1 80 MB /boot ext2 /dev/hda2 1 GB swap /dev/hda3 39 GB / ext3 Here's what I'd like to do. Partition a second hard disk (say, /dev/hdb) with three

Environment: CentOS 6.2 amd64 (min. server install) 2 virtual hard disks of 10GB each Linux KVM Following the instructions on CentOS Wiki <http://wiki.centos.org/HowTos/Install_On_Partitionable_RAID1> I installed a min. server in Linux KVM setup (script shown below) <script> #!/bin/bash nic_mac_addr0=00:07:43:53:2b:bb kvm \ -vga std \ -m 1024 \ -cpu core2duo \ -smp 2,cores=2 \

Hello everybody, I installed Centos 6.2 on a computer with an older version of it in order to dual boot both of them. I managed to install the new OS on a physically seperated hard drive, and configured grub to make the newly installed OS the default one. Now the older OS won't boot and this error message shows: *"error 13: invalid or unsupported executable format"*. I attached

Hi all. I have a CentOS server: CentOS release 5.7 (Final) 2.6.18-274.3.1.el5 x86_64 I have two SSD disks attached: smartctl -i /dev/sdc smartctl version 5.38 [x86_64-redhat-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: INTEL SSDSA2CW120G3 Serial Number: CVPR13010957120LGN Firmware

Am 22.04.2016 um 12:40 schrieb g <geleem at bellsouth.net>: > greetings. > > centos 6.7 [current] > > > 'disk utility' has started showing message; > > WARNING: The partition is misaligned by 2560 bytes. This may > result in very poor performance. Repartitioning is suggested. > > for sdc5 - /home partition. > > /dev/sdc5 302243312

I am trying to mount a FAT32 partition in CentOS. I'm following the instructions on this page: http://www.linuxforum.com/linux_tutorials/14/1.php This is the line I put into /etc/fstab /dev/hda /mnt/windows vfat users,owner,rw,umask=000 0 0 And this is the error I get: [root at localhost mnt]# mount -a mount: wrong fs type, bad option, bad superblock on

Hello, I had a scientific linux 3.0.4 system (rhel compatible), with 3 ide disks, one for / and two others in linear raid (250 gb and 300 gb each). This system was obsoleted so i move the raid disks to a new scientific linux 3.0.7 installation. However, the raid array was not detected ( I put the disks on the same channels and same master/lsave setup as in the previous setup). In fact

On my computer with dual systems(win7+centos6.4(now 6.5), after I do something, problems came out: when I plug portable hard disk into my computer, It is not mounted successfully. SO I do as the suggestions from URL 'http://wiki.centos.org/TipsAndTricks/NTFS' with the following block: _/Installing required packages/_ _//__//__//__//_ _/For /__/*CentOS-6*/__/the

On my computer with dual systems(win7+centos6.4(now 6.5), after I do something, problems came out: when I plug portable hard disk into my computer, It is not mounted successfully. SO I do as the suggestions from URL 'http://wiki.centos.org/TipsAndTricks/NTFS' with the following block: _/Installing required packages/_ _//__//__//__//_ _/For /__/*CentOS-6*/__/the

Hello, I have a server working on centos 5.7-64 minimal installation. I have 3 separate physical drives: 120 gb ssd, 2x 3tb disks for storage. My linux installation is on ssd disk, and I want to make raid 1 for these two 3tb disks and store data, like under /mnt/data. Can you please tell me the path how this is possible? Thanks for your help! Best regards, Here are some output of commands I

On Wed, Aug 5, 2015 at 9:12 AM, Bowie Bailey <Bowie_Bailey at buc.com> wrote: > I am trying to upgrade my system from 500GB drives to 1TB. I'm going to guess that there are no IDE drives that have 4096 byte physical sectors, but it's worth confirming you don't have such a drive because the current partition scheme you've posted would be sub-optimal if it does have 4096

I'm trying to extend a logical volume and I'm doing as follow: 1- Run `fdisk -l` command and this is the output: Disk /dev/sda: 85.9 GB, 85899345920 bytes 255 heads, 63 sectors/track, 10443 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: