similar to: Centos 5.3 NetworkManager success story

Hi Folks, I'd like to install my USB-WLAN-Stick Netgear WG111v3. Ndiswrapper works correct after installing Kernel-Modules from atrpm ndiswrapper-kmdl-2.6.18-53.1.19.el5.centos.plus-1.52-16.el5.i686.rpm. But by calling wpa_supplicant with wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf -d machine freezes. My wpa_supplicant.conf:

hi all, this is my first hit on the mailing list. hope i m posting in the right place. well, i have a dell vostro 1510 laptop with broadcom wifi adapter. n it doesnt work! :( i installed the wifi drivers with ndiswrapper. iwconfig shows the following. [root at laptop ~]# iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. wlan0

On 09/24/2015 04:47 PM, Alvin Starr wrote: > Actually I do a similar thing. Do you? > I use a VM as my home/office firewall. If your laptop/server/smth is permanently wired to the internet, there's no problem to bridge this interface to the VM. But the topic starter wants to connect to the cable or wifi and still have a firewall VM. WiFi client connection with WPA(2) PSK encryption

On Thu, Sep 24, 2015 at 2:08 PM, Dmitry E. Mikhailov <d.mikhailov at infocommunications.ru> wrote: > On 09/24/2015 04:47 PM, Alvin Starr wrote: >> >> Actually I do a similar thing. > > Do you? > >> I use a VM as my home/office firewall. > > If your laptop/server/smth is permanently wired to the internet, there's no > problem to bridge this interface

I have been playing around with 3 ath based FreeBSD boxes and seem to have got everything going via WPA and a common PSK for 802.11x auth. However, I want to have a bit more certainty about things working properly. What tools do people recommend for sniffing and checking a wireless network ? In terms of IDS, is there any way to see if people are trying to bruteforce the network ? I see

Hello, I have the AR9285 wireless adaptor on an HP DV6-2128ca notebook. I can see it. it comes up in NetworkManager but never gets an IP. the router is a linksys using WPA/PSK security. Would/could someone please help me out trying to get this to work? Output of several commands follows: dmesg: ath: EEPROM regdomain: 0x69 ath: EEPROM indicates we should expect a direct regpair map ath:

I know people used Parprouted to help with bridging wired with wireless. Have a look at it. -- Sent from the Delta quadrant using Borg technology! Nux! www.nux.ro ----- Original Message ----- > From: "C. L. Martinez" <carlopmart at gmail.com> > To: "Discussion about the virtualization on CentOS" <centos-virt at centos.org> > Sent: Thursday, 24 September,

Dear All, I'm having trouble on 2 laptops Lenovo B580 since upgrading to Centos6.5. ( Because it's a Lenovo I cannot switch the network card for a better supported network card. ) There on the latest kernel : root at jac network-scripts]# uname -a Linux jac.cawdekempen 2.6.32-431.1.2.0.1.el6.x86_64 #1 SMP Fri Dec 13 13:06:13 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux With the help of

Interesting situation: First my system - HP NC4010, with Atheros pci mini card. Latest MadWiFi drivers from: http://atrpms.net/dist/el4/madwifi/ and wpa from: http://atrpms.net/dist/el4/wpa_supplicant/ I had just the madwifi working back in Jul at the IETF conference. But as open only. I had upgraded to the plus kernel, thinking it would get my internal SD card reader working (it

Hello listmates, I feel a little embarrassed but I can not get through this one and any help will be much appreciated. I have a Broadcom WiFi adapter in a 64-bit CentOS 6.5 laptop. Trying to get it connect automatically - and it just would not - no error messages, nothing. With the same config NetworkManager connects without a hitch, I have to compile the wl module out of an SRPM - but after

Actually I do a similar thing. I use a VM as my home/office firewall. It works quite well and I would argue it is as secure as your standard firewall based on something like openWRT running on dedicated hardware. I also run a wireless AP in bridged mode to allow local network access on an appliance. There should be no reason that you could not put both on the same physical hardware. As for

I am using a Netgear MA401 with the wi driver, and am having trouble using wpa_supplicant to set static WEP keys. I have the wlan_wep.ko module loaded with wlan and wi built into the kernel. My wpa_supplicant.conf looks like this: ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=wheel network={ ssid="INTERNERD" scan_ssid=1 priority=1 key_mgmt=NONE

Hi, I am running Centos 4.1 on a Dell D610 with ipw2200. Any good howto for running wpa-psk? I have searched and not found much related to RHEL or CentOS. -- Thanks http://www.911networks.com

I seem to be able to lock my machine by going into wpa_cli and asking it to 'reassoc'. The reason for question mark after "hard" is that debug information (caused by wlandebug and athdebug) is being printed on the console. The only way to get machine's attention is to hold power button for 8 seconds. Note: manual reassociation is just the handy way to reproduce the problem

Hello, I'm trying to setup my wireless on FreeBSD 9.0-p3 amd64 and i get the following error: wpi0: fatal firmware error pciconf -lv: wpi0@pci0:3:0:0: class=0x028000 card=0x10518086 chip=0x42228086 rev=0x02 hdr=0x0 0 vendor = 'Intel Corporation' device = 'PRO/Wireless 3945ABG [Golan] Network Connection' class = network Detected as: wpi0:

On 09/24/2015 03:21 PM, C. L. Martinez wrote: > Thanks Dimitry, but I use wlan0 or eth0 to connect my laptop to > different networks. I use a vm as fw and I would like to have all vms > and laptop behind this fw vm guest. > > Another option is to assign an IP to these interfaces and natting all > to this fw vm ... but I don't like this option It isn't going to be safe,

WPA-2 (WPA Enterprise) fails with the new kernel(s) using ndiswrapper and wpa_supplicant. I haven't tried other authentication modes because that entails changes in the wireless setup which I am loathe to make right now. (It's a Broadcom mini pci card, so I have to use ndiswrapper with this Dell laptop. Bummer!). Rebuilding the newest wpa_supplicant rpm from the FC5 source rpm's

first, the short form of the question -- has anyone got that wireless adapter working on centos 5.5 and associated with an access point that uses WPA/WPA2 security? and the details. in a classroom where there is *no* wired networking at all, all PCs have only that wireless net adapter, which works fine on windows but, after installing centos 5.5, unsurprisingly, we have no networking. there

I have an Everex laptop (ick, but it was super cheap) that has an Atheros wireless NIC in it, but I can't seem to get it to connect to my wireless in-home LAN. Here's what I've done so far (that isn't working) - any suggestions? [root at marktop mark]# lspci | grep Ether 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 7c) 05:01.0 Ethernet controller:

So far I have upgraded 2 test laptops (no big servers or this, my main laptop). I am running from local repos. The OS repo is from downloading the isos and extracting them. The Update repo I get with an rsync command. On both laptops, the update ends with a dialog panel (oh, I am using gnome): The NetworkManager applet caould not find some required resources. It cannot continue. I