similar to: ALT_BREAK_TO... + ILO ... missing something in config ...

Hi all, A recent thread inspired me to try getting a proper serial console working on a Supermicro X9SCL motherboard with IPMI. However I find that while I see loader messages and the getty I enabled after boot I don't get any kernel messages which does somewhat limit the utility.. The BMC creates COM3 (/dev/cuau2) which works with getty. I modified /boot/loader.conf like so..

Hi, I have built a FreeBSD 7.0RC2 system to use both the serial and video consoles. I find that when I drop into single user mode (shutdown now) on the terminal connected to the box itself I do not see the single user mode prompt on the serial console terminal. Likewise, when I drop to single user mode on the serial console I do not see the single user prompt on the terminal connected to

I can't seem to get my serial terminal to work with my new system. I had a serial terminal connected to my old system that worked great and copied /boot.config, /boot/loader.conf and /etc/ttys settings over from it. The new system has a Gigabyte GA970A-UD3 board with just a serial header on the board. I bought a serial connector backplate in an electronics store and connected it to the

Hi all, I have had this problem since day 1 on my new server. It has run since November 15th 2008, and serve approx. 10 GB worth of web traffic per month for the main site and then some 40 domains with mail and small web pages. (hence - it's NOT that busy yet) I started with 7.1-RELEASE-pX since I didn't have problems straight off - but it didn't last long. After a few days of

I'm getting the following warning, and then the system locks: ACPI Warning: Incorrect checksum in table [(bunch of spaces)] - 0x29, should be 0x48 Here's a pic: http://db.tt/O6dxONzI System is on a SuperMicro C7X58 motherboard that I just upgraded to BIOS 2.0a, which I would like to stay on if possible. I tried adjusting all the ACPI related BIOS settings without success. Bryce

Hi, is the above supposed to work? I tried to follow what is written in the installation manual: unplugging the keyboard does nothing, booting with 'boot -h' gives me all the kernel's device probing messages on both the serial console and the normal console, but after 'mounting root from ...' sysinstall appears on the normal console. harti

This is a fairly standard and old machine with 2 COM ports. Recently (last Friday) I decided to update my RELENG_7 system and also to transition from sio to uart. This what I had before the upgrade: kernel: sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 kernel: sio0: type 16550A kernel: sio0: [FILTER] kernel: sio1: <16550A-compatible COM port> port

We have upgraded a box from 6.2 to 6.3-RELEASE. Afterwards the box does not recognize its ST Lab I-160 serial card with Netmos 9845 Chipset. It worked flawlessly on 6.2 with puc(4) driver. >From dmesg: pci1: <simple comms, UART> at device 8.0 (no driver attached) ~# pciconf -l -v | grep -B 4 UART none2@pci1:8:0: class=0x070002 card=0x00041000 chip=0x98459710 rev=0x01 hdr=0x00

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm trying to run a QEMU VM on top of a FreeBSD 7.x server ... I've tried the exact same setup on my desktop, using 192.168.1.x and an fxp device, and it all works perfectly, but as soon as I do this on another machine on a public IP, I'm not getting any routing, I can't even ping it from the same machine ... My first thought was

Dear All, Currently i am using HP x6600 Server and I have installed RHEL4 Update 4 AS Linux and RHEL4 Update 4 Support Cluster Suite in my server I am new in fence and can any one help me how to configure HP ILO fence in my server and HP ILO Fence Functionality Regards -S.Balaji

Hello, Has anyone managed to redirect output of kickstart install to ILO serial console? I have to test and deploy the remote install with kickstart but have trouble debugging it because I can't see the output. -- Jure Pe?ar http://jure.pecar.org

I am writing a hp ilo module to automatically assign a static ip that is derived from the IP of the system which is fed in via facter. I basically just need to change the network the ilo is connected to. The ruby code works great inside the irb console. However, puppet doesn''t seem to be able to use the variable I have derived from the ipaddress. This is my first template so I am not

Hello, Recently, the FreeBSD base system OpenSSH was upgraded to OpenSSH_5.1p1 FreeBSD-20080901, OpenSSL 0.9.8e 23 Feb 2007 Before the upgrade, with OpenSSH_4.5p1 FreeBSD-20061110, OpenSSL 0.9.7e-p1 25 Oct 2004 I had no troubles connecting to the ssh server built-in into the HP Proliant G5 ILO management board, authenticating by id_dsa, v2 protocol. On that board, ssh server greets with

On Fri, 10 Mar 2006, Herta Van den Eynde wrote: > I'm trying to install Red Hat Advanced Server AS 4 on a HP Proliant DL380G4. > Unlike e.g. the DL360, the DL380 does not have the option to set the OS in the > BIOS. > As soon as the installation starts, i.e. even before you get to the point > where you can enter "boot" and whatever boot options you want to use, the

Hey, Does anyone know how I can capture both Xen & Dom0 console output on a "Virtual Serial Port" from HP''s iLO (Integrated Lights-Out) interface? Plain linux is no problem, but combined with Xen it seems to go haywire :-) So far I''ve been combining options and the only thing that actually gave me some output (albeit only the Xen console, not dom0) was this:

Just a note to pass on in case anyone runs into the same situation. I have a DELL R510 that is running just fine, up until the day that I needed to import a pool from a USB hard drive. I plug in the disk, check it with rmformat and try to import the zpool. And it sits there for practically forever, not responding. The machine still responds to network connections etc., it''s just the

We are in the process of migrating one of our embedded apps to use uart by default instead of sio in RELENG_7 in prep for the day when sio eventually disappears. Unfortunately, the application doesnt want to work with uart with puc backed devices, but still works with sio. Stranger still, the app works with the uart driver when uart attaches to the built in com port on the isa bus. However,

yo, ive been using the fstack protector for a while now and it worked fine until i was gonna compile 4.8p3 then i got these errors, sio.o(.text+0x18b7): undefined reference to `__guard' sio.o(.text+0x1da9): undefined reference to `__guard' sio.o(.text+0x1db9): undefined reference to `__stack_smash_handler' vga_isa.o: In function `isavga_probe': vga_isa.o(.text+0x10): undefined

Hello All, For some reason my asterisk server is not registering a port number with my VSPs. This is causing problems where people are not able to dial in from any of my SIP or IAX VSPs. I do have one VSP that has hard coded my IP and port so I can get incoming calls but this still leaves a problem with my other VSPs. Hose can I get asterisk to register my IP and port? I have been

Hi everyone, We are recently seeing a problem with OpenSSH 5.8p1 and SSH to ILO cards running SSH-2.0-mpSSH_0.1.0. This has previously worked with OpenSSH 5.5p1 (last known version for us to work). ssh ilohost -vvv gives the following on 5.8p1: debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Applying options for *.* debug2: ssh_connect: needpriv 0