similar to: [PATCH 2/9] Sched clock paravirt op fix.patch

Subject: Add a sched_clock paravirt_op The tsc-based get_scheduled_cycles interface is not a good match for Xen's runstate accounting, which reports everything in nanoseconds. This patch replaces this interface with a sched_clock interface, which matches both Xen and VMI's requirements. In order to do this, we: 1. replace get_scheduled_cycles with sched_clock 2. hoist cycles_2_ns

Subject: Add a sched_clock paravirt_op The tsc-based get_scheduled_cycles interface is not a good match for Xen's runstate accounting, which reports everything in nanoseconds. This patch replaces this interface with a sched_clock interface, which matches both Xen and VMI's requirements. In order to do this, we: 1. replace get_scheduled_cycles with sched_clock 2. hoist cycles_2_ns

In order to share the common code in tsc.c which does CPU Khz calibration, we need to make an accurate value of CPU speed available to the tsc.c code. This value loses a lot of precision in a VM because of the timing differences with real hardware, but we need it to be as precise as possible so the guest can make accurate time calculations with the cycle counters. Signed-off-by: Zachary Amsden

In order to share the common code in tsc.c which does CPU Khz calibration, we need to make an accurate value of CPU speed available to the tsc.c code. This value loses a lot of precision in a VM because of the timing differences with real hardware, but we need it to be as precise as possible so the guest can make accurate time calculations with the cycle counters. Signed-off-by: Zachary Amsden

VMI timer code. It works by taking over the local APIC clock when APIC is configured, which requires a couple hooks into the APIC code. The backend timer code could be commonized into the timer infrastructure, but there are some pieces missing (stolen time, in particular), and the exact semantics of when to do accounting for NO_IDLE need to be shared between different hypervisors as well. So

VMI timer code. It works by taking over the local APIC clock when APIC is configured, which requires a couple hooks into the APIC code. The backend timer code could be commonized into the timer infrastructure, but there are some pieces missing (stolen time, in particular), and the exact semantics of when to do accounting for NO_IDLE need to be shared between different hypervisors as well. So

VMI timer code. It works by taking over the local APIC clock when APIC is configured, which requires a couple hooks into the APIC code. The backend timer code could be commonized into the timer infrastructure, but there are some pieces missing (stolen time, in particular), and the exact semantics of when to do accounting for NO_IDLE need to be shared between different hypervisors as well. So

VMI timer code. It works by taking over the local APIC clock when APIC is configured, which requires a couple hooks into the APIC code. The backend timer code could be commonized into the timer infrastructure, but there are some pieces missing (stolen time, in particular), and the exact semantics of when to do accounting for NO_IDLE need to be shared between different hypervisors as well. So

Convert VMI timer to use clock events, making it properly able to use the NO_HZ infrastructure. On UP systems, with no local APIC, we just continue to route these events through the PIT. On systems with a local APIC, or SMP, we provide a single source interrupt chip which creates the local timer IRQ. It actually gets delivered by the APIC hardware, but we don't want to use the same local

Convert VMI timer to use clock events, making it properly able to use the NO_HZ infrastructure. On UP systems, with no local APIC, we just continue to route these events through the PIT. On systems with a local APIC, or SMP, we provide a single source interrupt chip which creates the local timer IRQ. It actually gets delivered by the APIC hardware, but we don't want to use the same local

Critical bugfixes for the VMI-Timer code. 1) Do not setup a one shot alarm if we are keeping the periodic alarm armed. Additionally, since the periodic alarm can be run at a lower rate than HZ, let's fixup the guard to the no-idle-hz mode appropriately. This fixes the bug where the no-idle-hz mode might have a higher interrupt rate than the non-idle case. 2) The interrupt handler can no

Critical bugfixes for the VMI-Timer code. 1) Do not setup a one shot alarm if we are keeping the periodic alarm armed. Additionally, since the periodic alarm can be run at a lower rate than HZ, let's fixup the guard to the no-idle-hz mode appropriately. This fixes the bug where the no-idle-hz mode might have a higher interrupt rate than the non-idle case. 2) The interrupt handler can no

Use para_fill instead of directly setting the APIC ops to the result of the vmi_get_function call - this allows one to implement a VMI ROM without implementing APIC functions, just using the native APIC functions. While doing this, I realized that there is a lot more cleanup that should have been done. Basically, we should never assume that the ROM implements a specific set of functions, and

Use para_fill instead of directly setting the APIC ops to the result of the vmi_get_function call - this allows one to implement a VMI ROM without implementing APIC functions, just using the native APIC functions. While doing this, I realized that there is a lot more cleanup that should have been done. Basically, we should never assume that the ROM implements a specific set of functions, and

In a virtualized environment, virtual machines will time share the system with each other and with other processes running on the host system. Therefore, a VM's virtual CPUs (VCPUs) will be executing on the host's physical CPUs (pcpus) for only some portion of time. The VMI exposes a paravirtual view of time to the guest operating systems so that they may operate more effectively in a

In a virtualized environment, virtual machines will time share the system with each other and with other processes running on the host system. Therefore, a VM's virtual CPUs (VCPUs) will be executing on the host's physical CPUs (pcpus) for only some portion of time. The VMI exposes a paravirtual view of time to the guest operating systems so that they may operate more effectively in a

Hi Peter, Removal of VMI(VMware's para-virtualization technique) is scheduled for 2.6.37, I was wondering what would be the right time frame for submitting a patch which does that. Does the x86-tip tree have any next branch where we can park this patch ? Below is the patch for your reference which just removes VMI specific bits, applies on top of x86-tip. There is also an opportunity to

Hi Peter, Removal of VMI(VMware's para-virtualization technique) is scheduled for 2.6.37, I was wondering what would be the right time frame for submitting a patch which does that. Does the x86-tip tree have any next branch where we can park this patch ? Below is the patch for your reference which just removes VMI specific bits, applies on top of x86-tip. There is also an opportunity to

Hi Andi, This is a set of updates for the firstfloor patch queue. Quick rundown: revert-mm-x86_64-mm-account-for-module-percpu-space-separately-from-kernel-percpu.patch separate-module-percpu-space.patch Update the module percpu accounting patch fix-ff-allow-percpu-variables-to-be-page-aligned.patch Make sure the percpu memory allocation is page-aligned

Hi Andi, This is a set of updates for the firstfloor patch queue. Quick rundown: revert-mm-x86_64-mm-account-for-module-percpu-space-separately-from-kernel-percpu.patch separate-module-percpu-space.patch Update the module percpu accounting patch fix-ff-allow-percpu-variables-to-be-page-aligned.patch Make sure the percpu memory allocation is page-aligned