similar to: [PATCH 10/10] Fix BusLogic to stop using check_region

Hi Andi, This is a set of updates for the firstfloor patch queue. Quick rundown: revert-mm-x86_64-mm-account-for-module-percpu-space-separately-from-kernel-percpu.patch separate-module-percpu-space.patch Update the module percpu accounting patch fix-ff-allow-percpu-variables-to-be-page-aligned.patch Make sure the percpu memory allocation is page-aligned

Hi Andi, This is a set of updates for the firstfloor patch queue. Quick rundown: revert-mm-x86_64-mm-account-for-module-percpu-space-separately-from-kernel-percpu.patch separate-module-percpu-space.patch Update the module percpu accounting patch fix-ff-allow-percpu-variables-to-be-page-aligned.patch Make sure the percpu memory allocation is page-aligned

On my x86_64, I pulled down the source for the 2.6.18-92.1.13 kernel and followed the wiki faithfully, but it will not build. I'm getting errors in the Buslogic driver: In file included from drivers/scsi/BusLogic.c:56: drivers/scsi/BusLogic.h:241: error: redeclaration of enumerator 'false' include/linux/stddef.h:16: error: previous definition of 'false' was here

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Hello, I have the subject mentioned mb and I am trying to install centos 4.4 with sata raid enabled, but linux is not seeing the drives? I tried to load via sata raid driver, no luck there. I guess I could try legacy mode in the bios, but I was hoping there is another way around to load linux with the raid? Thanks....

I used to use a hot-plugable PATA-CDROM drive on my Computer (Samsung P35 laptop). To change drive I use a script which at the bottom of its heart uses Code: echo "scsi remove-single-device 1 0 0 0" | sudo tee /proc/scsi/scsi and Code: echo "scsi add-single-device 1 0 0 0" | sudo tee /proc/scsi/scsi commands in oder to let the OS being aware of the changed drive. This

Heya all, I'm experiencing some problems with a TDM40P and was wondering if anyone else on this list has similar experiences, or maybe even a possible solution. My setup is a dual PIII-750 with 1 gig of RAM, with an X100P, connected to an analog line to my telco, and a TDM40P with analog phones connected. The TDM-card is not sharing any interrupts, but the X100P is, with the 2 Adaptec SCSI

we have DELL R900 with CENTOS 5.3 in it. This DELL R900 come with one integrate PERC6/I and two PERC6/E card. DELL 6/I control 5 internal disks. The original disk sequence are: /dev/sda1 /boot /dev/sda2 / /dev/sdb1 swap ... after I configured PERC6/E disks and reboot, /dev/sda change to RAID disk and original /boot and / change to /dev/sde1 and /dev/sde2. My modprobe.conf is: alias

Hi, does anyone have any recommended (read tried and tested) way of making asterisk be able to handle incoming faxes. I've a PC running asterisk with a digium E1 card in and simply want to be able to route a call to some application which will take a fax call and save the fax as an image. I guess the bits I'm unsure of are how to terminate a fax call without a modem (if this is