similar to: [Bridge] Bridging vlans...

Hello. I''m running linux box with Slackware 9.1 and compiled kernel 2.4.31 with "yes" to VLANs and "yes" to all QoS. On this box i have more ethernet interfaces: eth0 eth1 eth2 and so as more vlan interfaces: eth0.100 eth1.3 eth1.4 This is entrace(uplink) router to our whole network and my goal is to shape users on this machine. I want for this purpose use HTB so

Hello. I''m trying to use vlan in domU, but have something strange: I created bridge on eth0. This interface was configured as trunk with vlan 300, 301. I use this bridge in my domU, and I can see tagged packets when run tcpdump in domU. Also I created interface on domU to work with vlan 300. On this interface I see untagged packets in vlan300. And everything looks fine. But when

Hi all, i need config xen with this ___________ __________ |VM1 |----------------bridge1-------------------| | |__________ | | | ____________ | |-----BALBLA |VM2 |

Hello, I'm trying to use bridging in our servers and found a problem with dhcp. Some clients manage to get an IP from the server, using DHCPDISCOVER/DHCPREQUEST. However others use BOOTREQUEST and these don't seem to get an answer. The server sends a BOOTREPLY but the clients continue to send BOOTREQUEST for ever. There are also some (occasional) messages from the dhcp server like

Hello You must add first: vlan (tagged) to eth2 eth2 interface is not tagged by default and not know vlan-s . It is like a cisco if you have 24 ports in cisco by default all ports are in vlan1. if you want to do trunk (with vlans) you myst add (vlans) to this ports (tagged or untagged) So you can compare that all interfaces in linux by default are in one vlan(but not tagged). (only for

Hi, I'm using Vlans in my network as a way of preventing pier to pier communication - I only want nodes in the network to talk to the gateway (a linux box). I have successfully set up lots of sub interfaces using the vconfig too, one for each vlan. What I would like to be able to do is remove the ip address from each of these subinterfaces eth0.x and bridge them to eth0. I have successfully

Hi to the ML. I''m new to VLAN configuration, and combining it to XEN is a bit difficult. I want to use VLAN because it''s possible to "arping" from a domU to an other, and VLAN looks like; the only solution to prevent that. May be I''m wrong if someone got a solution, I may be interrested. I''ve also tryed ebtables, but nothing to prevent arp

Hi, In one of our xen server, I am using two bonding. bond0 : Is for trunk, where the vlans are attached , port eth0 & eth1 is attached to bond0 bond1 : eth2 & eth3 are attached to bond1, where physical ip has been set . In the /etc/xen/xend-config.sxp, I am using (network-script *multi-network-bridge*) , the

Hi, I am facing issues after upgrading one of the server from rhel5.5. (86_64) to latest rhel5.7 (86_64). The server is under trunk configuraion. I have set the network bridge as follows: #!/bin/bash vconfig set_name_type DEV_PLUS_VID_NO_PAD dir=$(dirname " $0" /etc/xen/scripts/network-bridge $@ vifnum=1 bridge=xenbr2 netdev=bond0.10 /etc/xen/scripts/network-bridge $@

re can somebody tell me what am I doing wrong (at this late night hour), because vlan are not getting bridged at all. ifconfig eth0 0.0.0.0 up ifconfig eth1 0.0.0.0 up brctl addbr br0 brctl addif br0 eth0 brctl addif br0 eth1 ifconfig br0 up vconfig add br0 X vconfig add br0 Y X = vlan-ID (example: 222) Y = vlan ID (example: 223) # brctl show bridge name bridge

Hi, examining the network traffic with wireshark shows that asterisk does not set any QoS values at all. What do I need to do to make asterisk set QoS values (on Centos 7)? The wiki says to use vconfig to set QoS values[1]. What does the skb-priority need to be set to? How do you use vconfig on interfaces that are not VLAN interfaces? Is it generally impossible to set QoS values on

I have 3 machines, T60 thinkpad with e1000 NIC Dell PowerEdge 2950 with bnx2 NIC HP DL360 G4P with tg3 NIC All running xen 3.03 / 2.6.16.29-xen I have a netbootable image with 2.6.16.29-xenU. This image when it boots creates a vlan eth0.4002, and then tries to communicate on that interface to a central server. On the machines with e1000 an bnx2 NICs, this works fine. On the

--- In english --- Hello! I am to implement a new architecture of the network in my company but I do not know right where to start ... need help! Currently 90% of my servers are virtual machines under Xen. I have many valid IP networks and all Hypervisors are configured in bridge mode, to simplify. We have 3 VMWare ESX Hypervisor also in bridge mode. Some networks are exclusive to certain

Hi, After reading XenServer documents and debugging, I found the previous configuration is correct, here is the one I've configured to work: In XCP, as in XenServer, system's network configuration doesn't really matter, it only make sense before XCP starts and handles the network settings. So there is no need to configure VLAN on host machine, and you only need a minimal one active

Hi All, I''m using xen 3.0 on CentOS 5 with VLAN. #vconfig add eth0 100 #/etc/xen/script/network- bridge start vifnum=1 netdev=eth0 bridge=xenbr0.100 I know that after xen 3.2 the procedure of bridge configuration is changed. What is the correct command to set bridge interface to vlan? Yukio

Hello list, I've posted here about this before, but I realise that it may have been assumed that the bridged vlans simply put a switch port in a blocking state and left my question ignored. So to recap. I have two tg3 interfaces named 'in' and 'out' and a bridge named 'br0' My vlan trunk is on the 'in' side of the network, and set as in.2, in.3 ... The

I have a first version of a virtual configuration module in perl for *. There is also a simple web editor at the url that uses this module. Asterisk::VConfig lets you have multiple users each with their own copy of the configuration files on the same asterisk server. It also has some limited permission settings to limit access to particular parts of the config files, and a single/multiuser

I just added 802.1Q VLAN support to redhat initscripts. And after support was ready, I tried to restart shorewall. Well it blew into pieces. Seems like shorewall can''t handle device names like: eth0.3 very properly. That''s default naming of vlan devices. eth1 is master device and 3 is id of my test vlan. So when I added to interfaces line: home eth0.3 detect seems like

Hii All, VLAN is create in manageable switch, like Cisco Catalyst and other vlan cap= able switch. eac port in that switch can be assigned in different VLAN. so,= that switch capable to insert 802_1q to each incoming frame (Please correc= t if its wrong, i just newbie in VLAN).I want build VLAN but i don't have v= lan capable switch. Is possible to create a vlan capable switch using switc=

so first off wow works on wine but wines being gay and when i hit maximize it maximizes but the actual wow window is still the same size and i have problems running tf2 on crossover it tells me "Setup file 'gameinfo.txt' doesnt exist in subdirectory 'hl2'. Check your -game paramater or VCONFIG setting.and tf2 works fine if i just switch over to ms home edition by restarting.