similar to: [Bridge] bridge wlan-eth

hi list members, my goal is to make one of my DomU''s act as a wireless accesspoint... So, i need it to have access to the pcmcia wlan card attached to dom0. But how ? when i give the pci=[] option to the domU config file its shows up with lspci but i cant use it... (on debian with module-assistent get rt2x00 in de DomU) Is it possible or would it be better to use a more direct interface

Hello, I want to add wireless capability to my Gentoo-linux based firewall/router at home, so I bought a Netgear MA311 PCI and installed the hostap package. I load the hostap_pci module and the wlan0 interface comes up fine. I can detect the signal from a wireless enabled laptop. Now I'm thinking I'm going to bridge the wlan0 interface and the eth1 interface, and run the firewall with br0

Hi All, After hours of reading and trials, I got the following setup working... 1. Dell Axim X30 PocketPC with 802.11b wireless using DHCP with Open WEP -- successfully connected to --> 2. Laptop with DLink Airplus DWL-650+ PCMCIA wireless with ndiswrapper v1.1 driver with network bridge (wired + wireless) and running a DHCP server listening on interface br0 (eth0 + wlan0) Here is the

I am having problem in ping or connect AP from Mobile Node(essid & channel is the same,maybe routing did not set properly but i fail to configure with route add default gw 192.168.3.4,its alway said network is unreachable ),My Mobile Node is using acx100 as driver while AP(redhat 9.0) is using HOSTAP 0.1.3.Any one can help? I heard How-To said we not need to set address on eth0 & wlan0

So, I'm setting up my first bridge, and I'm running into an interesting issue. I have a 4 port NIC (formerly 4 seperate /29 and /28 LANs) and an onboard NIC (to my ISP). I've setup the bridge using the script included at the bottom of this email (modified from Gentoo for Aurora). When the WET11 (the WET11 is a simple ethernet to wireless bridge) is unplugged, the bridge works

[desktop] ----- lan ----eth0 [notebook] eth1 192.168.?.? ` ----- wlan ---- [speedport(hub and router)] -- internet 192.168.2.x So on my laptop I have eth0 beeing lan, eth1 beeing wlan ethernet card. When only using eth0/1 everything is fine. Now I want to be able to use internet from both [desktop] and [notebook]. Typically you set up a bridge with

Hallo, can I use pxelinux for booting a notebook via WLAN? Viele Gruesse! Helmut

Hi list, I bought two UTStarcom F1000 phones, pre-equipped with the latest firmware, including WPA support. Those are configured to register to an asterisk server on the internet (not LAN), and registration works. Calling and being called also, with transfer and all bells and whistles. After a few minutes up to 5 hours (varies widely), the display tells me that an Accesspoint is not available

Hello, is anyone on the list using a normal cell/mobile phone which is able to act as a SIP client over WLAN? Or has anyone heard of a SIP client for cell/mobile phones running windows mobile 6.x? The phone should use SIP, when the asterisk server is reachable and should automatically switch to a German telco if it is not reachable. Thanks for any hints, Stefan --

Hello, I manage a number of servers all running 2.4 (same problem exists with 2.6). My problem is that since a few bridge versions ago, I've had to modify net/bridge/br_fdb.c in the br_fdb_insert() function -- to get rid of the checks that produce this error: Jan 16 10:35:31 host15 kernel: tap_0: received packet with own address as source address Jan 16 10:35:33 host15 kernel: tap_0:

Hello I've got this Mini-PC https://www.zotac.com/product/mini_pcs/zbox-ci323-nano everything is fine -> latest 6.8 kernel works; both Ethernet-Interfaces work and also the WLAN-Interface works; the two Ethernet-Interfaces are eth0 and eth1 the WLAN-Interface is wlan0 eth1 is connected on ISP side eth0 is connected on my LAN side to a switch; and wlan0 shall also be on my LAN side f?r

Hello, I'd like to add rules (level workstation) for ignoring wlan reconnects/disconnects. The rules would ignore messages like this: May 12 11:02:16 t400 kernel: [13254.204101] No probe response from AP <MAC> after 500ms, disconnecting. May 12 11:02:16 t400 kernel: [13254.213029] cfg80211: Calling CRDA to update world regulatory domain May 12 11:02:16 t400 wpa_supplicant[3277]:

I intend to realize the connection to the Internet by WLAN (at the presen time DSL cable modem). The WLAN DSL-Router should not be the problem. But which wlan- adapter (internally (PCI), USB... whatever) can be recommended for a work "out of is the box" with cent OS 5? Thx Timothy

I have a Broadcom 802.11b/g hardware on my dual-boot laptop. Note first that in the WinXP partition, the wifi makes DHCP connections to my router with no problem. Since this was not working in my new CentOS 6 partition, and remembering that there was a driver problem with the old Fedora partition it replaced, I followed instructions founs at:

Hi everyone, My PC don't have an integrated WLAN card, so I bought an USB WIFI device which use the MediaTek MT7601U chip(image 'dongle.jpg'). ------------------------------------------------------------------------------------------------------ My PC specification- OS = CentOS 7.8.2003. Processor = AMD Ryzen 5 1600. Mother-Board = GA-Gigabyte A320M-S2H

Hi folks! First post here, so please don't bother if it's not the right place to post those kind of questions. I'm currently running a 4.7-release (upgrade to 4.8 planned but not yet started) on my production box. As I would like to setup a small WLAN (major use for my notebook, other clients are possible) I need to know which cards are really supported. The handbook is IMHO not

Hello, In one of our project we need to connect one IMX 27 based baord which ahs a internal FEC controller & an MPC 8323RDb baord which has a Built in Network controller. We need to connect the IMX27 based board to MPC board thro cross cable & MPC baord has wlan AP card . Basically we want to communicate from IMX27 to wireless network. Hence we are planning to make follwoing arranage

Hi, I?ve been following some information about the latest chan_sccp drivers for a few weeks. I installed and tried about any variant of driver that exists in the chan_sccp system. Despite a few little changes in the CLI options I am still encountering a lot of problems with the phone. When not using the phone for a while, it "disconnects" from asterisk (1.0.7) after a few hours

Hello, Thanx in advance to anyone who can help me get this going. I have tinkered around and around with this and I have it functioning as a visible access point that I can connect to. My problem comes in when trying to access the internet. I''m not an iptables guru or anything but I got the following as my iptables startup to supposedly masq the connection correctly:

Hi! It is possible to start domU''s with dependencies? I mean something like that: 1. start domU a 2. wait till domU a completely started 3. start domU b 4. wait till domU b completely started 5. start all other domU''s How to do it? Greetz PS: sorry for my english _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com