similar to: [Bridge] modprobe: modprobe cannot locate br0 modules

Hi, Sorry,after i install bridging 1.4, even after i setup a new bridge to link between wlan0 & eth 0 but it seem lost after pc restart, i have to reset after restart. am i doing wrong in installation or ... Hope get some advice from u all (expert) ===== Ô¸ÄúÓÀÔ¶ÐÒ¸££¬¿ìÀֺͰ²Ïê Happy & Healthy Always ! ^_^ ! ¸öÈËÍøÒ³ Homepage:http://planet.time.net.my/sunwaycity/ceyong ¸öÈË·ðѧÍøÒ³

Hi, i am using bridge-utils-1.0.4 in my redhat 9.0 pc, even i configure my bridge called br0 which bridging wlan0 & eth0 but after computer restart, it disapprear, how can we statically set it. I did write configuration and save as ifcfg-br0 . Anyone can help, Thanks! ===== Happy and Healthy Always ! ^_^ ! My Homepage : http://planet.time.net.my/sunwaycity/ceyong My Buddhist Pages:

I am having problem in ping or connect AP from Mobile Node(essid & channel is the same,maybe routing did not set properly but i fail to configure with route add default gw 192.168.3.4,its alway said network is unreachable ),My Mobile Node is using acx100 as driver while AP(redhat 9.0) is using HOSTAP 0.1.3.Any one can help? I heard How-To said we not need to set address on eth0 & wlan0

All is in subject. Example : root@harobed:~ # brctl show bridge name bridge id STP enabled interfaces root@harobed:~ # ifconfig lo Lien encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:H?te UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16510 errors:0 dropped:0 overruns:0 frame:0

hi: my box use eth0 connect my pc. but I type command "./brctl showmacs br0", no mac addr display and the" brctl showmacs program" not exit,always exec # ./brctl show bridge name bridge id STP enabled interfaces br0 8000.000123456789 no eth0 hdlc0 # ./brctl showmacs br0

I''ve just gotten xen-4.0.1-rc4-pre on top of Ubuntu 10.04 using the 2.6.32.15 kernel source installed and booting into Dom0 thanks to you guys! I was under the impression that xend would setup at least a basic bridge interface and some vif interfaces automaticlly.. I don''t get any of that. And when I try to start xend manually after reboot I get: ifdown: interface eth0 not

Hello, I am working with Xen 2.0.7; when I create my Dom0 it does not move eth0 onto the xen-br0 like it suppose to resulting in no network connectivity in Dom0. Why does this happen and what must I do to fix it? Thanks. Kashif _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

On Wed, Oct 16, 2013 at 01:52:57PM +0200, Maciej Gałkiewicz wrote: > Hi > > I am using Libvirt 1.1.2 with Openstack Havana (RC2, nova-network) and > openvswitch 1.4.2+git20120612-9.1. Libvirt vif driver ( > nova.virt.libvirt.vif.LibvirtGenericVIFDriver) generates config likes this: > > <interface type='bridge'> > <mac

On 16 October 2013 13:55, Daniel P. Berrange <berrange@redhat.com> wrote: > > Sounds like a host mis-configuration related to kernel bridge support > to me. > Could you tell me what might be mis-configured? I am using kernel 3.10.11, modules openvswitch, bridge, stp and llc are loaded. regards -- Maciej Gałkiewicz Shelly Cloud Sp. z o. o., Sysadmin http://shellycloud.com/,

On Wed, Oct 16, 2013 at 02:04:47PM +0200, Maciej Gałkiewicz wrote: > On 16 October 2013 13:55, Daniel P. Berrange <berrange@redhat.com> wrote: > > > > Sounds like a host mis-configuration related to kernel bridge support > > to me. > > > > Could you tell me what might be mis-configured? I am using kernel 3.10.11, > modules openvswitch, bridge, stp and llc

Am 24.02.19 um 16:51 schrieb Brian Davis via samba: > On a machine with virtual networking is enabled and two ether net > controllers eth0/192.168.1.2 and eth1/192.168.1.3 and having SAMBA smb.conf > set to: > > dns interfaces = lo br0 > > is there a chance for: > > 1) The system not to boot with DNS working > 2) The DNS server bounce between eth0 and eth1 > 3)

Greetings, I'm just wondering how one can make the bridging tools stop spamming the virtual consoles? I would rather have all those "entering forwarding state", "entering learning state" and "entering disabled state" messages go to a log than have them plastered all over whichever console I happened to be logged into to work. Thanks! -- Martin-Eric Racine

Hello! "brctl stp br0" would crash brctl provided that br0 is a bridge. This is caused by incorrect number of arguments in the commands table. "stp" needs at least 2 arguments after "stp". The patch against version 1.0.4 is attached. -- Regards, Pavel Roskin -------------- next part -------------- --- brctl/brctl_cmd.c +++ brctl/brctl_cmd.c @@ -394,7 +394,7 @@

On Wed, 16 Jun 2004 17:53:08 +0800 (CST) "vanyew" <vanyew@mail2000.com.tw> wrote: > Dear Stephen, > > I'm a Linux embedded developer. > We want to build the bridge function on our product. > > We use brctl to build the bridge device. > > [root@localhost /]# brctl show > bridge name bridge id STP enabled interfaces >

Hi I am using Libvirt 1.1.2 with Openstack Havana (RC2, nova-network) and openvswitch 1.4.2+git20120612-9.1. Libvirt vif driver ( nova.virt.libvirt.vif.LibvirtGenericVIFDriver) generates config likes this: <interface type='bridge'> <mac address='fa:16:3e:44:30:a4'/> <source bridge='br0'/> <model type='virtio'/>

https://bugzilla.netfilter.org/bugzilla/show_bug.cgi?id=479 Summary: tunnel0 and br0 Product: iptables Version: 1.2.11 Platform: i386 OS/Version: other Status: NEW Severity: normal Priority: P2 Component: iptables AssignedTo: laforge@netfilter.org ReportedBy: tom@tomdeb.org I have a ipsec

Hi Robert, 2. Any ideas of something to try in order to make this repeatable? > = What i would do to reproduce it, is make a script establishing the bridge, = then flooding the bridge with some external ping -f, then shuting down the = bridge. If there is a refcount release problem, it should appear on eavy = load (some buffer overflow, or something like that). Also, are you playing with

https://bugzilla.netfilter.org/bugzilla/show_bug.cgi?id=479 netfilter@linuxace.com changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |netfilter@linuxace.com ------- Additional Comments From netfilter@linuxace.com 2006-06-28 02:57 MET ------- Tom - did

https://bugzilla.netfilter.org/bugzilla/show_bug.cgi?id=479 ------- Additional Comments From kaber@trash.net 2006-05-22 14:42 MET ------- It is not entirely clear what you are trying to show with that LOG line. How is the traffic flowing, what do you expect? And why is it visible in plaintext on the br0 device? Please also include your kernel version. -- Configure bugmail:

Hello, I wanted to get an extra IP on my local NIC, so I ran `sudo ip addr add 192.168.1.130/24 dev enp4s0`. This didn't work as intended, so I thought I'd restart the Ubuntu system to have things back to how they were. Alas, this didn't happen. While the host still has network as usual, none of the VMs are able to get a DHCP lease from the router, or any connectivity at all. I can