similar to: [Bridge] Error in usb0 and eth0 bridging on an ARM9 Plattform

Hi there, I've just started to work with the great speex encoder on ARM9-based embedded platform. This is my configuration: CPU: Cirrus Logic EP9315 @ 200 MHz (ARM920T) o.s.: Linux 2.6.9-rc2-ep93xx GCC: gcc version 3.3.3 (DENX ELDK 3.1 3.3.3-10) without MaverickCrunch support ogg library: 1.0 speex command line configuration: ./configure --enable-fixed-point --enable-arm4-asm The code is

Hi I intent to use brctl to bridge two devices on linux box. One is eth0, the other is USB net which is recognized as usb0 by linux box. Then I run following command # ifconfig eth0 down # ifconfig usb0 down # brctt addbr ipbr # brctl addif ipbr eth0 # brctl addif ipbr usb0 # ifconfig eth0 up # ifconfig eth0 0.0.0.0 # ifconfig usb0 up # ifconfig usb0 0.0.0.0 # ifconfig ipv6 up

Hi llandre, I think it's worth trying the float version on your CPU. However, I wouldn't be surprised if the fixed-point was still faster than float. BTW, you can use --enable-arm5-asm instead of --enable-arm4-asm. While both are currently almost the same, eventually it would be possible to get better performance using the ARM5E DSP-like instructions. Jean-Marc > This processor

Hi Jean-Marc, >I think it's worth trying the float version on your CPU. However, I >wouldn't be surprised if the fixed-point was still faster than float. ok, I'll try both configurations. >BTW, you can use --enable-arm5-asm instead of --enable-arm4-asm. While >both are currently almost the same, eventually it would be possible to >get better performance using the

Hi; I meet some problem when porting openssh.Please help me The following content is wrong info: # strace ssh execve("/usr/bin/ssh", ["ssh"], [/* 16 vars */]) = 0 mmap2(NULL, 20, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40005000 stat("/etc/ld.so.cache", {st_mode=S_IFREG|0644, st_size=1796, ...}) = 0 open("/etc/ld.so.cache",

The Wine development release 5.11 is now available. What's new in this release (see below for details): - Wine Mono engine updated to 5.1.0, with WpfGfx library support. - More work on the separate Unix library for NTDLL. - Beginnings of a NetIO kernel driver implementation. - Initial support for the Print Ticket API. - Removal of the obsolete 32-bit PowerPC architecture. -

Hello, I'm trying to connect some windows machines together using tinc 1.0.6. The basic connectivity (ping) works fine as expected. But I'm getting really poor speeds over the tinc tunnel. The test machines are on the same switch and get values ranging from 6-9 MBytes/s speaking directly to each other. However over the tinc tunnel the speeds are in the range of 20-40 kbytes/s. The machines

All, I see the following message fairly frequently in our nsd.log files: error: failed reading from tcp: Connection reset by peer A quick grep through the source code reveals that this log message comes from server.c, and can come pretty much at any time during a TCP query. Since: - This condition occurs during normal operation, and - There is nothing a server operator can do about it. I

Hi, 1 I got message "The specified network name is no longer = available" show on PC/Win2000 when copy large files to ARM9 base = NAS(with SAMBA 2.2.8 + Linux Kennel 2.4.18) file size is correct but content appended with all "0" in = ARM9 NAS HDD. 2. At the console of ARM9 NAS show : ..... root@sword:/var# . smbd[170]: PAM

Hi We are running a OpenBSD 3.6 server with squid 2.5.STABLE7 configure options: --enable-auth=ntlm,basic --enable-external-acl-helpers=wbinfo_group --localstatedir=/var/squid --enable-snmp. We are running samba with vers 3.0.4 with winbind support This is our samba file workgroup = apac netbios name = auasv-00001 server string = Sydney LAN Proxy security = domain password server =

Hi, samba 3.0.24, debian etch I'm seeing a strange effect with samba and traffic over a bond0 interface in round robin mode. 2 server each with 2 GbE interfaces as bond0 device ind rr mode. netio benchmark: NETIO - Network Throughput Benchmark, Version 1.26 (C) 1997-2005 Kai Uwe Rommel TCP connection established. Packet size 1k bytes: 182840 KByte/s Tx, 197599 KByte/s Rx. Packet size

On Mon, 21 Dec 2009 21:00:01 +0100, <speex-dev-request at xiph.org> wrote: > Thank you for your product Speex. We want to use it in > microcontroller AT91SAM7S256 (48 MHz). I'd strongly advice to use a higher performance micro. Let's consider that you'd succeed in getting it working right after optimizations. The time you want to add other speex features or other

Hi all, I am trying to get some decent speed out of a vanilla Debian (Proxmox) box and am running out of ideas. Basically I can exchange data at 110MB/sec (raw, nfs, ftp) but not with Samba shares. I tried almost every samba tuning tip I could find to no avail. The only optimisation left to smb.conf at the moment is debug level = 0. As one can see the robocopy throughput is merely half of what

I found a message from you to the asterisk users mailing list from 2001. I was wondering if you got (or still have) an asterisk system working with the linejack? If so, would you be willing to assist me with mine? I seem to have things working, and * says that caller ID is coming in, but I can't get * to actually answer the call. Thanks, Greg -- NetIO.org

The Wine development release 5.10 is now available. What's new in this release (see below for details): - More progress on the WineD3D Vulkan backend. - Beginnings of a separate Unix library for NTDLL. - Better support for anti-cheat kernel drivers. - More glyph substitutions in DirectWrite. - Support for DSS private keys. - ARM64 exception handling fixes. - Various bug fixes.

Has anyone tried using BroadVoice for VSP? I have Asterisk configured for a home office & I've been trying to decide which VoIP provider to go with for a little while now. I had heard you could get sub $.01 calls but I have not found that to be true yet (not saying it's not possible, I just haven't found it!). Also I'm not sure if BV will support multiple lines. Any

The Wine development release 5.12 is now available. What's new in this release (see below for details): - NTDLL converted to PE format. - Support for the WebSocket API. - Improved RawInput support. - Vulkan spec update. - Various bug fixes. The source is available from the following locations: https://dl.winehq.org/wine/source/5.x/wine-5.12.tar.xz

ACE issued following PR: http://www.ace.nl/news/aces-cosy-compiler-framework-outperforms-llvm-arm9-processor Weird that they don't give any number and use ARM 9, do they mean cortex-a9 ?

Hello Everybody! I set up a fileserver: - Pentium II, 350 Mhz, - 256MB RAM, - Intel Fast Ethernet PCI - VIA-SATA Controller - 2x500GB SATA HDD RAID 1 - Debian 4, Samba 3 - Samba set up in user shares mode without special options, but with the suggested optimizations Clients: - Windows XP Prof SP2 So far it works fine. I can read and write files without problem.

Hello, I would like to run nut 2.6.1 on an embeeded machine ( arm9 ) running linux and uclibc. A working gcc tool chain came with the board. How can I compile and build nut using the cross compiler tool chain ? I know that this is not a very specific question. I have however little experience with cross compiling, and I wonder where to start. A logical point would be the configure script. It