similar to: [Bridge] how do i bridge eth0 with eth1 by bridging?

Hello all, I'm trying to bridge the wlan0 and eth0 on an embedded system. I used the following commands to setup the bridge: ifconfig eth0 0.0.0.0 promiscuous ifconfig wlan0 0.0.0.0 promiscuous brctl addbr br0 brctl addif br0 eth0 brctl addif br0 wlan0 brctl sethello br0 1 brctl setmaxage br0 4 brctl setfd br0 4 ifconfig br0 up The eth0 is connected to a local network, and wlan0 is set to

I am trying to bridge a ppp connection to an ethernet connection. The documentation says this is possible but when issuing the following: brctl addif myBridge ppp0 a short message is displayed br_add_interface: Cannot assign requested address -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.linux-foundation.org/pipermail/bridge/attachments/2007042=

Hello, I?m using the Linux Bridge on an Atmel Arm9 Plattform with the kernel 2.6.11rc3. The configuration is the following: LAN<--Arm9(Ethernet)--Bridge--Arm9(USB-Device)-->Notebook (USB-Host) or LAN<--Arm9(Ethernet)--Bridge--Arm9(USB-Host)-->Notebook (USB-Host) (with a Trust USB2.0 Host to Host cable) When I try to ping my Notebook from LAN and reverse, everything seems to be

Hello I am using linux box as a network loadbalance router. ----------------- ------------ |LAN| - |eth0 eth1(1.1.1.2) | DSL1 ------- |DSLAM (1.1.1.1) | | eth2(1.1.1.10) | DSL2 ------- |DSLAM (1.1.1.9) | ---------------- ------------ But I have a

Very strange and as you suggested delete the ifcfg-eth0 file and recreate, specify your settings. I suspect your wireless device and or systemboard is faulty. Is there a BIOS hardware self-test you could perform to check the integrity of your hardware? On Sun, Feb 9, 2020, at 8:10 AM, Nicolas Kovacs wrote: > Hi, > > I've done my fair share of CentOS 7 installations, but this is the

Hello, Am Sonntag, 9. Februar 2020, 14:10:44 CET schrieb Nicolas Kovacs: > Hi, > > I've done my fair share of CentOS 7 installations, but this is the first > time I have this kind of weird problem. Here goes. > > In my office I have a battered Dell Optiplex 320 PC with two NICs that I'm > using as a bare metal sandbox server for testing purposes. > > The

Le 09/02/2020 ? 14:10, Nicolas Kovacs a ?crit?: > Any suggestions ? I forgot to add. The onboard NIC is a Broadcom card. $ lspci | grep -i net 02:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8100/8101L/8139 PCI Fast Ethernet Adapter (rev 10) 02:09.0 Ethernet controller: Broadcom Inc. and subsidiaries BCM4401-B0 100Base-TX (rev 02) This card gets randomly renamed to either

Le 09/02/2020 ? 16:54, Alexander Dalloz a ?crit?: > "Kernel always uses the ethX naming convention at boot when it enumerates > network devices. Due to parallelization, the order of the kernel interface > enumeration is expected to vary across reboots." Thanks for the heads up. I experimented quite a bit, and found some surprising behavior. So I documented everything in a

Le 10/02/2020 ? 16:12, Leroy Tennison a ?crit : > There may be ways to force NIC naming, I've done so but only on Ubuntu so > you'll need to do the research if it's important to you. Things to look for > based on my experience: 70-persistent-net.rules, net.ifnames=0, > biosdevname=0. That's exactly the solution I described in detail in my blog article. :o) --

Hello, I have a routing configuration that I''ve been working on and seems to be working well for me. I''d like to ask for some peer review. If your interested and can take a moment to consider this I could use some advice on if this correct. I''m still very much learning, sorry if this email is off topic or too long or anything. I want to route a wireless network

Hello list, I need to know how to deal with a redundant network with only one asterisk server, which is receiving registrations from the end points on both of its ethernet ports. This means extension 201 is registering both from eth0 and from eth1. Is there a way/software which can act as a middle man between asterisk and the ethernet ports, and by default sends registrations to asterisk only

Hi Everyone: I installed CentOS 4.4 on a new Dell 2950 using the server cd. No errors during the installation and no errors on bootup when loading the Eth0 or Eth1 interfaces. I currently have iptables stopped and selinux disabled. The interfaces have been given a static ip (192.168.1.x). the subnet is 255.255.255.0 and the gateway is 192.168.1.1. I can not ping any device on my network

Dear all, Has anyone experienced this whilst running DRBD over eth1 between two CentOS 5.7 servers? eth1 is a private IP address, unroutable. eth0 is the public address. CentOS will reply sometimes once every 3 days or every 14mins~ saying "My public IP is on eth1" to arp requests when it's not, it's eth0. This freezes traffic and causes issues. We've looked at arp*

There may be ways to force NIC naming, I've done so but only on Ubuntu so you'll need to do the research if it's important to you. Things to look for based on my experience: 70-persistent-net.rules, net.ifnames=0, biosdevname=0. ________________________________ From: CentOS <centos-bounces at centos.org> on behalf of Nicolas Kovacs <info at microlinux.fr> Sent: Sunday,

Am 09.02.2020 um 16:14 schrieb Nicolas Kovacs: > Le 09/02/2020 ? 14:10, Nicolas Kovacs a ?crit?: >> Any suggestions ? > > I forgot to add. The onboard NIC is a Broadcom card. > > $ lspci | grep -i net > 02:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. > RTL-8100/8101L/8139 PCI Fast Ethernet Adapter (rev 10) > 02:09.0 Ethernet controller: Broadcom Inc.

Hi, I've done my fair share of CentOS 7 installations, but this is the first time I have this kind of weird problem. Here goes. In my office I have a battered Dell Optiplex 320 PC with two NICs that I'm using as a bare metal sandbox server for testing purposes. The CentOS 7 installer sees the connected network card as eth0. But after the first reboot, the interface comes up as eth1.

Hello, In one of our project we need to connect one IMX 27 based baord which ahs a internal FEC controller & an MPC 8323RDb baord which has a Built in Network controller. We need to connect the IMX27 based board to MPC board thro cross cable & MPC baord has wlan AP card . Basically we want to communicate from IMX27 to wireless network. Hence we are planning to make follwoing arranage

On 21/02/06, Bráulio Gergull <gergull@getnet.com.br> wrote: > Hi, > > I''ve had a similar problem. I found it to be due to crc checksum errors. > > I solved that with "ethtool -K ethN tx off" on all domU''s. > > I found some related info on the following thread: > > http://lists.xensource.com/archives/html/xen-users/2006-01/msg00088.html

Hi all, i'm having an issue with my bridge. I have the following network: ADSL router (192.168.0.1) ------ [eth0] Bridge (192.168.0.2) [eth1] ------- Workstation (192.168.0.3) Bridge works, but after some minutes, my eth1 card (8139too driver) goes link down and link up, disabling access to the bridge IP for a while (bridge functionality for workstation works ok). This happens between

Hello, I am working on Network-Simulation (VNUML). Our simulator uses linux bridgi= ng to connect the UMLs. So there is one problem: The example is the following: There are two hosts simulating one big net. The two hosts have connection over the external nets Net3 and Net6 (see htt= p://www.uni-koblenz.de/~timbub/verteilteSim3.GIF), but in fact there is onl= y one physical connection between the