similar to: LVM + kickstart -> dom0 && domUs

hi, The problem: for kvm/qemu disks are /dev/vdx devices when using the virtio driver. For vmware, drives are /dev/sdx devices. For hp servers, /dev/ccisss/whatever (sorry, no proliant with an array controller handy to check it). in order to just have one kickstart script to maintain I am trying to use the %pre section but getting a bit stuck. This is what I have: %pre if [ -b /dev/sda ] then

Hi. I'm currently trying to configure a kickstart script to do auto installs. We split up the partitions so that we have control on the mount security like setting no execute on the tmp portions etc . I keep hitting the same error : "Could not stat /dev/VolGroup00/LogVol_root --- No Such file or directory The device apparently does not exist; did you specify is correctly " Even

Hi all, I still use the following kickstart partition scheme for C7 installations (via virt-install): Briefly, fixed size for /root and /boot, and the rest is filled up for /srv. The same kickstart (despite that c7 uses vda, f29 uses sda) doesn't work with Fedora29 (EL8). I get a "device is too small for new format" error. Any hints? part /RESCUE --fstype="ext4"

Hey, Can anyone tell me why option 1 works and option 2 fails ? I know I need swap and such, however in trouble shooting this issue I trimmed down my config. It fails on trying to format my logical volume, because the mount point does not exist (/dev/volgroup/logvol) It seems that with option 2, the partitions are created and LVM is setup correctly. However the volgroup / logvolume was not

I'm testing doing kickstart installations on Xen VMs. This is the first time I'm trying out kickstart at all, so I rather think I'm doing something wrong in the kickstart configuration than it is a Xen issue. I use a modified kickstart file from an earlier manual installation with a very basic filesystem setup. It fails with "SystemError: vgcreate failed for VolGroup00".

I have a kickstart file with the following partitioning directives: part /boot --fstype ext3 --onpart=sda1 part pv.100000 --onpart=sda2 --noformat volgroup vol0 pv.100000 --noformat logvol / --vgname=vol0 --name=lvol1 --useexisting --fstype=ext4 logvol /tmp --vgname=vol0 --name=lvol2 --useexisting --fstype=ext4 logvol swap --vgname=vol0 --name=lvol3 --useexisting logvol /data --vgname=vol0

Hello Group, I am building a company application based on Centos 5.7 OS. The application was working earlier and creating right partitions both for hardware as well as VM. But since we introduced Centos 5.7 OS and start building application with 5.7 anaconda the hardware partitions are duplicate of VM partitions *while creating hardware partition my code looks like.* cat >

Dear All, I'm trying to create a kickstart installer. I specified an option --byes-per-inode to 'logvol' command, but I got a message "No such option: --bytes-per-inode" during installation. Does anybody know a solution? The following is the lines for disk partitioning definition specified in my kickstart file. ------------------------- ## ## Disk partitioning information

I am testing some kickstarts on ESXi virtual machine with pair of 16GB disks. Partitioning is lvm over raid. If i am using "logvol --grow i get "ValueError: not enough free space in volume group" Only workaround i can find is to add --maxsize=XXX where XXX is at least 640MB less than available. (10 extents or 320Mb per created logical volume) Following snippet is failing with

Hello Gentlemen, I would like to ask a question about an issue I have with the Centos 6.3 installation. I have installed a Centos 6.3 on a server we used before with 5.4 on Friday. I have created a KS file to let me connect to the server via VNC and have all repos and packages preconfigured. I only needed to partition the hard drive using VNC. During the partition process I selected which

On Wed, 8 May 2019 at 13:24, mark <m.roth at 5-cent.us> wrote: > Leon Fauster via CentOS wrote: > > Hi all, > > > > > > I still use the following kickstart partition scheme for C7 installations > > (via virt-install): > > Briefly, fixed size for /root and /boot, and the rest is filled up for > > /srv. > > > > The same kickstart

Has anyone managed to create an encrypted disk partition with CentOS 8 kickstart? 1 reqpart --add-boot 2 part /boot --fstype ext3 --size=1024 --ondrive=sda 3 part pv.1 --size=1 --grow --ondrive=sda --encrypted --pashphrase="bla" 4 volgroup vol0 pv.100000 5 logvol / --vgname=vg_00 --name=lv_root --size=102400 --fstype=ext4 ... No matter what I specify in line 3, the installer bombs out.

Hi, I'm trying to create a kickstart file that uses a thinly provisioned lvm volume as root but I've run into trouble. I installed a System manually using this option and this is the anaconda file produced: part /boot --fstype="xfs" --ondisk=vda --size=500 part pv.10 --fstype="lvmpv" --ondisk=vda --size=7691 volgroup centos_centos7 --pesize=4096 pv.10 logvol

I am trying using a kickstart file to install CentOS 6.2 into a new virtual machine (the MBR sector of the harddisk is all zero), however I found that the installer cannot go through the harddisk partition. It failed after I chose "Use All Space" at harddisk partition option. The error message is: http://anony.ws/i/bMcTJ.png "You have not defined a root partition (/), which is

I'd like to automate the upgrade from CentOS 4.6 to 5.1 as much as possible. Since upgrades per se are not really recommended, I'm planning to do a kickstart installation. However, I want to leave one of the existing partitions (/scratch) untouched during the installation. Here is my current layout (LogVol00 is swap so not shown in the df output below): # df -hl

I am asking this here, that although a kickstart question, may have something to do with the Centos install? I took my Anaconda-ks.cfg from my system, turned it into a ks.cfg and did the install. Everything SEEMS ok, but why? First the partitioning information: ks.cfg supplied: clearpart --all --drives=hda part /boot --fstype ext3 --size=100 --ondisk=hda part / --fstype ext3 --start=14

>> Dave wrote: >>> Hi, >>> >>> Thanks for your reply. Yah i do have apache running, your idea >>> certainly would make things easier. How did you set up the http area? >>> And where in it do you put the kickstart? I'd like this area to be >>> accessible to my local network only, internet users shouldn't be able >>>

> Am 08.05.2019 um 19:20 schrieb mark <m.roth at 5-cent.us>: > > Leon Fauster via CentOS wrote: >> Hi all, >> >> >> I still use the following kickstart partition scheme for C7 installations >> (via virt-install): >> Briefly, fixed size for /root and /boot, and the rest is filled up for >> /srv. >> >> The same kickstart

Hi, just to avoid re-inventing the wheel, is there any document that can help me reduce even further a "minimum" installation of Centos 4.4 (BTW can you say 600mb is minimum)? I am in the process of creating a small Centos-4.4-based Asterisk box and I need to boot it from a CF card. Deleting useless packages will help me do what i want. Example: even a minimum install of Centos 4.4 (or

Hi, just to avoid re-inventing the wheel, is there any document that can help me reduce even further a "minimum" installation of Centos 4.4 (BTW can you say 600mb is minimum)? I am in the process of creating a small Centos-4.4-based Asterisk box and I need to boot it from a CF card. Deleting useless packages will help me do what i want. Example: even a minimum install of Centos 4.4 (or