similar to: Autoreplace not working

I had a drive fail and replaced it with a new drive,During the resilvering process,that show "Too many errors",and process fail. now,the pool can online,but cannot accept any zfs''s commands that change pool''s state,I can list File directory,but don''t mv?cp and rm -f. what can I do,I need that data files. root at opensolaris2:~# cat /etc/release

I am trying to test a new setup of NV74. I have set up the system with ZFS boot. Everything works fine until I pull a drive. The system locks up when I try to run any command e.g. zpool status. There is no communication with the server from then on. It does not even respond to pings. Setup - Supermicro SC836TQ-R800 Chassis Supermicro X7DB8 Motherboard Supermicro SAT2-MV8 SATA controller

Hi, After upgrading to b95 of OSOL/Indiana, and doing a ZFS upgrade to the newer revision, all arrays I have using ZFS mirroring are displaying errors. This started happening immediately after ZFS upgrades. Here is an example: ormandj at neutron.corenode.com:~$ zpool status pool: rpool state: DEGRADED status: One or more devices has experienced an unrecoverable error. An attempt was

Hey, On Sat, Oct 31, 2009 at 5:03 PM, Victor Latushkin <Victor.Latushkin at sun.com> wrote: > Donald Murray, P.Eng. wrote: >> >> Hi, >> >> I''ve got an OpenSolaris 2009.06 box that will reliably panic whenever >> I try to import one of my pools. What''s the best practice for >> recovering (before I resort to nuking the pool and

I encountered a strange libzfs behavior while testing a zone fix and want to make sure that I found a genuine bug. I''m creating zones whose zonepaths reside in ZFS datasets (i.e., the parent directories of the zones'' zonepaths are ZFS datasets). In this scenario, zoneadm(1M) attempts to create ZFS datasets for zonepaths. zoneadm(1M) has done this for a long time (since

Greetings, my Opensolaris 06/2009 installation on an Thinkpad x60 notebook is a little unstable. From the symptoms during installation it seems that there might be something with the ahci driver. No problem with the Opensolaris LiveCD system. Some weeks ago during copy of about 2 GB from a USB stick to the zfs filesystem, the system froze and afterwards refused to boot. Now when investigating

Hello, Sorry for the (very) long subject but I''ve pinpointed the problem to this exact situation. I know about the other threads related to hangs, but in my case there was no < zfs destroy > involved, nor any compression or deduplication. To make a long story short, when - a disk contains 2 partitions (p1=32GB, p2=1800 GB) and - p1 is used as part of a zfs mirror of rpool

I have an OpenSolaris snv_101 box with ZFS on it. (Sun Ultra 20 M2) zpool name is rpool. The I have a 2nd hard drive in the box that I am trying to recover the ZFS data from (long story but that HD became unbootable after installing IPS on the machine) Both drives have a pool named "rpool", so I can''t import the rpool from the 2nd drive. root at hyperion:~# zpool status

I''ve hit this bug on my home machine couple of times and finally decided to log it since I''ve spend 2 days configuring my "OpenSolaris 2008.11 snv_101b_rc2 X86" and after installing the SUNWsmbfskr package I ended up in the grub> menu. The package contains a necessary module for CIFS. After pkg install SUNWsmbfskr, I rebooted the box. There was no grub menu anymore

I have configured a test system with a mirrored rpool and one hot spare. I powered the systems off, pulled one of the disks from rpool to simulate a hardware failure. The hot spare is not activating automatically. Is there something more i should have done to make this work ? pool: rpool state: DEGRADED status: One or more devices could not be opened. Sufficient replicas exist for

Hello, Has anyone encountered the following error message, running Solaris 10 u8 in an LDom. bash-3.00# devfsadm devfsadm: write failed for /dev/.devfsadm_dev.lock: Bad exchange descriptor bash-3.00# zpool status -v rpool pool: rpool state: DEGRADED status: One or more devices has experienced an error resulting in data corruption. Applications may be affected. action: Restore the file in

Hello... Since there has been much discussion about zpool import failures resulting in loss of an entire pool, I thought I would illustrate a scenario I just went through to recover a faulted pool that wouldn''t import under Solaris 10 U5. While this is a simple scenario, and the data was not terribly important, I think the exercise should at least give some piece of mind to those who

I had to use the labelfix hack (and I had to recompile it at that) on 1/2 of an old zpool. I made this change: /* zio_checksum(ZIO_CHECKSUM_LABEL, &zc, buf, size); */ zio_checksum_table[ZIO_CHECKSUM_LABEL].ci_func[0](buf, size, &zc); and I''m assuming [0] is the correct endianness, since afterwards I saw it come up with "zpool import". Unfortunately, I

(for some reason I cannot find my original thread..so I''m reposting it) I am trying to move my data off of a 40gb 3.5" drive to a 40gb 2.5" drive. This is in a Netra running Solaris 10. Originally what I did was: zpool attach -f rpool c0t0d0 c0t2d0. Then I did an installboot on c0t2d0s0. Didnt work. I was not able to boot from my second drive (c0t2d0). I cannot remember

Sorry for the long post but I know trying to decide on hardware often want to see details about what people are using. I have the following AS-2022G-URF machine running OpenGaryIndiana[1] that I am starting to use. I successfully transferred a deduped zpool with 1.x TB of files and 60 or so zfs filesystems using mbuffer from an old 134 system with 6 drives - it ran at about 50MB/s or

Dear ZFS experts, I have 2 SATA 500 GB Hard Drive on my Dual Core PC I have installed OpenSolaris 2008.11 using Live CD I got from Sun Tech Days in Singapore Now, using all the guidelines I got here at Indiana Discussion, I can''t attach my second drive to rpool to make them mirror Initially I was playing around with similar configuration in VirtualBox, and it does not succeed. Finally

I''ve installed Open Solaris 2009.06 on a machine with 5 identical 1TB wd green drives to create a ZFS nas. The intended install is one drive dedicated to the OS and the remaining 4 drives in a raidz1 configuration. The install is working fine, but creating the raidz1 pool and rebooting is causing the machine report "Cannot find active partition" upon reboot. Below is command

Not sure what the best list to send this to is right now, so I have selected a few, apologies in advance. A couple questions. First I have a physical host (call him bob) that was just installed with b134 a few days ago. I upgraded to b145 using the instructions on the Illumos wiki yesterday. The pool has been upgraded (27) and the zfs file systems have been upgraded (5). chris at bob:~# zpool

Not sure what the best list to send this to is right now, so I have selected a few, apologies in advance. A couple questions. First I have a physical host (call him bob) that was just installed with b134 a few days ago. I upgraded to b145 using the instructions on the Illumos wiki yesterday. The pool has been upgraded (27) and the zfs file systems have been upgraded (5). chris at bob:~# zpool

While testing a zpool with a different storage adapter using my "blkdev" device, I did a test which made a disk unavailable -- all attempts to read from it report EIO. I expected my configuration (which is a 3 disk test, with 2 disks in a RAIDZ and a hot spare) to work where the hot spare would automatically be activated. But I''m finding that ZFS does not behave this way