similar to: Promise SX4060 on 7.1-BETA2

Hi, after one month with gmirror and gjournal running on a 7.0-RELEASE #p2 amd64 (built from latest CVS source), the box hung a couple of times when on high disk load. Finally, while building some port it won't boot for no reason obvious to me. This is what I get with kernel.geom.mirror.debug=2: ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire ad4: 476940MB <SAMSUNG HD501LJ

Hi After my previous email about the SETFEATURES SET TRANSFER MODE timeout on (msgid 441AA807.5090100@wfeet.za.net , 17 March 14:18 GMT + 2 on freebsd-stable), I installed FreeBSD 6.1 BETA 4 and upgraded to a 6-STABLE kernel, running the box in 'safe' mode to do so. I now, however, get a slightly different error message: ad4: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout

Hello I have this problem: Yesterday server with FreeBSD 6.0 was self restarted . In messages was this: Mar 8 20:03:11 mail kernel: ar1: WARNING - mirror protection lost. RAID1 array in DEGRADED mode Mar 8 20:03:11 mail kernel: ar1: writing of Intel MatrixRAID metadata is NOT supported yet Mar 8 20:03:11 mail kernel: subdisk8: detached Mar 8 20:03:11 mail kernel: ar1: writing of Intel

Say I have a raidz of 3 disks: ad4 ad6 ad8 I want to tell zfs that I am pulling ad4 and replacing it with a new disk on the same controller, but I can''t get it to release its hold on ad4. [0138][root at ztest:/home/matt]# zpool offline pond ad4 Bringing device ad4 offline [0140][root at ztest:/home/matt]# zpool replace pond ad4 cannot replace ad4 with ad4: ad4 is busy

Hi I have a newly installed FreeBSD 6.0 release machine on which I am getting the following error on the console: "ad4: req=0xc23bc258 SETFEATURES SET TRANSFER MODE semaphore timeout !! DANGER Will Robinson !!" This is generally associated with heightened disk activity, but it happens inevitably after a while (minutes or hours) if the machine is running. The atacontrol list shows:

Hi all, I have some problems with my gvinum setup after the system panic'ed. Afterwards the system fails finding the plexes to the subdisks (or at least that is what I can understand after having searched the gvinum source code for the error string in the DMESG log..) The machine is an IBM Netfinity 5000 and the internal HW self tests does not find any errors in the hw. Luckily my root is

Before reading below: I am considering a new install rather than an upgrade of our servers. However, now I just want to beat this problem. :) At 02:19 PM 7/8/2003 +0000, Phil Pennock wrote: >On 2003-07-08 at 14:09 +0000, Phil Pennock wrote: > > There was a fairly major update to the IDE disk device handlers which > > required new device nodes. Bringing in the new MAKEDEV script

I've tested both 6.3 and 7.0-RC2, amd64 architecture, and have found the occurrence of an interrupt storm using an ASUS A8N-SLI Premium (nForce 4) motherboard with an AMD Opteron 175. Relevant dmesg output: atapci0: <nVidia nForce CK804 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 6.0 on pci0 ata0: <ATA channel 0> on atapci0 ata1: <ATA

I made a bad judgment and now my raidz pool is corrupted. I have a raidz pool running on Opensolaris b85. I wanted to try out freenas 0.7 and tried to add my pool to freenas. After adding the zfs disk, vdev and pool. I decided to back out and went back to opensolaris. Now my raidz pool will not mount and got the following errors. Hope someone expert can help me recover from this error.

hi, latest changes in dev/ata broke this, on older -stable ... ata0-master: pio=PIO4 wdma=UNSUPPORTED udma=UNSUPPORTED cable=40 wire ad0: success setting PIO4 on National chip ad0: 977MB <SanDisk SDCFB-1024 Rev 0.00> at ata0-master PIO4 on latest -stable: ata0-master: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=40 wire and no disk. cheers, danny

Hi all! According to www.freebsd.org/releases/5.1R/hardware-i386.html#AEN63 FreeBSD doesnt seem to support the PDC20378 chipset. Anyway, output of dmesg, atapci0: <Promise PDC20378 SATA150 controller> port 0xdc00-0xdc7f,0xdfa0-0xdfaf,0xdf00-0xdf3f mem 0xfeac0000-0xfeadffff,0xfeafe000-0xfeafefff irq 11 at device 4.0 on pci2 more dmesg output: ar0: ERROR - array broken

Hi there colleagues, atapci3: <nVidia nForce MCP55 SATA300 controller> port 0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb807,0xb480-0xb483,0xb400-0xb40f mem 0xefcb3000-0xefcb3fff irq 23 at device 5.2 on pci0 atacontrol detach ata7 - insert ATA disk (ad14) atacontrol attach ata7 pinics with Fatal trap 12: page fault while in kernel mode (kgdb) bt #0 doadump () at pcpu.h:196 #1 0xc0533227

I am having problems with silent data corruption on (some) drives connected to an MCP55 SATA controller. I have two servers, both running RELENG_7_0/amd64. One has the 570 Ultra chipset, the other has 570 SLI. Both chipsets have the MCP55 SATA controller. The server with 570 Ultra chipset has a bunch of older 250GB SATA-150 drives hooked up to the MCP55 controller and it is working just fine.

Hello, This file server was upgraded from 6.2-RELEASE-p$something to 6.3-RELEASE-p3 (current RELENG_6_3 sources via csup) on August, 11 and rebooted to the new kernel on August, 12. The school is closed due to holidays. The only load is mail delivery to Maildirs via NFS from another server (just 50 mailboxes or so, none of them very busy) and nightly backups. I went there on August, 13 to perform

Thomas, Have spoken to Soren, from my bootlog he believes that the problem is in atapicam causing the system to lock up. He is happy to answer some questions but doesnt have time to delve into atapicam himself. Did you author atapicam, I have seen your name on the sourcecode, can you help me further? Whats next? Thanks Adam. -------------- next part -------------- An embedded message was

I have a couple of DVD drives (one drive, one burner) that used to play DVDs quite fine from 5.3 to somewhere in the 6.x branch. Nowadays I have to send them to PIO4 to play DVDs, because they'll just throw DMA not aligned errors around in UDMA33 or WDMA2 mode. Should someone be interested in this I'm willing to supply all necessary information, such as the exact drives, firmware

We run several RH7.2/7.3 servers & recently 2 of them, although still working fine, have started to show kjournald as generally using over 50% cpu% on 'top' - virtually continuously. Free cpu% generally less than 25% now! Both machines are also using software RAID5 EIDE ....... otherwise are standard server installs. Any info on what kjournald is & why it should have recently

I upgraded my Centos 4.7 server last night. Switched from a cheaper 50$ asus motherboard to a Supermicro motherboard. I also, using dd, copied entire 500g SATA seagate drive to new 500g SATA seagate drive so as to have two copies in case something went wrong. Anyway, now I keep getting this error: Nov 21 06:08:33 server kernel: hda: status timeout: status=0xd0 { Busy } Nov 21 06:08:33 server

I have a current RELENG_7 running on: http://www.supermicro.com/products/system/4U/7045/SYS-7045B-TR+.cfm with the -3+ IPMI card. I can interact with the BIOS, etc, but no joy once we get past the loader. Anyone have ideas? Attached is the kernel config, and the /var/run/dmesg.boot file. -- Larry Rosenman http://www.lerctr.org/~ler Phone: +1 512-248-2683

Hey folks, So what's the word on AHCI and bios drive geometry? I'm having a real pain of a time trying to get some 750gb sata drives running on my FreeBSD7 box in AHCI mode. It doesn't seem to matter what disk geometry I suggest to sysinstall, something complains of an invalid disk upon booting it. Actually, in AHCI mode the bios screen doesn't report any information on