similar to: IPMI and Dell ERA/O

Well, we're figure the board's got problems, but I installed OpenIPMI a couple weeks ago, and fired it up as a service, then added a cron job. That all ran well until last evening; we came in to find 5 zillion emails complaining Unable to open SDR for reading I worked my way through logs, and googling, and then trying to run ipmitool by hand, and it complains there's no such device as

Hello! I'm trying to install Centos 6.4 64 bit on this Xserve: http://www.everymac.com/systems/apple/xserve/specs/xserve-intel-xeon-2.8-eight-core-specs.html I got a bootloader from: http://blog.christophersmart.com/2009/07/23/linux-on-an-apple-xserve-efi-only-machine/ as none of the official Centos releases (full, minimal, network 64 bit) boot on this machine. They all crash when loading

Hallo *! I have a board SE7501HG2. - On 2.6.18 ipmitool works succefull. On Xen-3.1 (2.6.18) ipmitool say: # ipmitool sensor WARNING: Unknown SDR repository version 0x00 SDR record id 0x0000: invalid length 0 (see thread [ipmitool-devel] Unknown SDR version) - On page [4] as written: ipmitool -> BMC ---> i2c/smbus ''-> SDR - On Thread [9] was written:

Hi all, New to the list and (mostly) new to CentOS. We have just moved from running RHEL to CentOS on our main production servers. Anyway, I am configuring a couple of new SunFire v20z servers here at the moment and trying to get the systems' management interfaces to work fully under CentOS. First issue was trying to install the openipmi RPM from the CD that came with the SunFires, this RPM

I'm running 9.2-RC4 on a handful of desktop and server machines (both i386 and amd64). I have seen three panics (all vm_page_unwire) on one of those systems only (amd64 server) during the past week. The first two panics were triggered when shutting down the ntpd daemon (a recent development snapshot version of ntpd: 4.2.7p387). Exiting a later release (p388) has not triggered the panic.

Hi all, A recent thread inspired me to try getting a proper serial console working on a Supermicro X9SCL motherboard with IPMI. However I find that while I see loader messages and the getty I enabled after boot I don't get any kernel messages which does somewhat limit the utility.. The BMC creates COM3 (/dev/cuau2) which works with getty. I modified /boot/loader.conf like so..

Hi all, I am trying to load kernel module ipmi_si, while failed with error "No such device", truth is I can find file in ../kernel/drivers/char/ipmi/ipmi_si.ko. So why I can't load it? Steps: # ls -l /lib/modules/2.6.32-573.el6.x86_64/kernel/drivers/char/ipmi/ipmi_si.ko -rwxr--r--. 1 root root 93080 Jul 23 2015

My environment is "heterogeneous" my authentication and home server are currently stuck on a 1G shared network, the production servers and storage servers are on a bonded 40G network, all are in the same VLAN. I have about 100 servers on the 40GB bonded network each with 12cores and 128GB of memory. They are running centos 6.6 Except for my storage servers they are all just running

Good morning! On a CentOS 6.4 / 64 bit server I have installed the watchdog 5.5 package. The rpm -qi watchdog states: The watchdog program can be used as a powerful software watchdog daemon or may be alternately used with a hardware watchdog device such as the IPMI hardware watchdog driver interface to a resident Baseboard Management Controller (BMC). ... This configuration file is also used to

Control: tag -1 +moreinfo On Tue, 2014-05-13 at 08:55 -0700, Mike Egglestone wrote: > After booting into kernel 3.13 dom0, the keyboard no longer works. > All other aspects work, ssh is needed to login to the system to > start working with the domU's. > They keyboard works at the grub menu just fine, and > works normal when booting into the non xen kernel. I think at a minimum

I have a current RELENG_7 running on: http://www.supermicro.com/products/system/4U/7045/SYS-7045B-TR+.cfm with the -3+ IPMI card. I can interact with the BIOS, etc, but no joy once we get past the loader. Anyone have ideas? Attached is the kernel config, and the /var/run/dmesg.boot file. -- Larry Rosenman http://www.lerctr.org/~ler Phone: +1 512-248-2683

On Thu, Jul 12, 2018 at 07:27:58PM -0500, Chris Adams wrote: > > Default Gateway IP : 192.168.0.100 > > Default Gateway MAC : 00:25:90:0a:42:87 > > No, that does not look right. You have configured the gateway of the > IPMI to be the host OS side of the NIC. You can't do that... in a lot > of systems I've seen, the IPMI side of the NIC can't even

This is that system with the missing management port, and I'm still fighting it. Everything *looks* right: 3: enp6s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 00:25:90:0a:42:87 brd ff:ff:ff:ff:ff:ff inet 192.168.0.100/24 brd 192.168.0.255 scope global enp6s0 ip route 192.168.0.0/24 dev enp6s0 proto kernel scope link

My Dell PowerEdge T105 running Centos-5.2 has started crashing fairly often (3 times in the last 2 hours). The message on the screen tells me to look at the System Event Log. Is this just /var/log/messages ? I didn't see anything helpful there. As far as I could see, the last messages before the crash were about samba, which is running on the machine. Has anyone had such problems with Samba?

Greetings all, I am looking for a solution to use IPMI (BMC) in with LibVirt (Virt-Manager). Actually there is a Customer behind this request as well. Trying to be short: We are looking for a Solution in OpenStack Environment. Customer wants to have the entire environment running in Virt-Manager (probably for a P.O.C or tests purposes). So here is what he is trying to do: http://red.ht/1HfNn9r

Is there a little setup display right on the box? Just asking because I have seen that on some boxes. Cheers, Boris. On Sun, Sep 18, 2016 at 12:15 AM, Keith Keller < kkeller at wombat.san-francisco.ca.us> wrote: > On 2016-09-17, Alice Wonder <alice at domblogger.net> wrote: > > > > Okay if it requires DHCP this might be out, I'm currently out of town > >

Hi, I hope somebody can help me with this problem. I don't know whether it's a problem with my configuration or a bug or feature in extlinux. I am using an IPMI 2.0 serial-over-lan console to connect to a system with an Intel S3200SHL motherboard. The first line of my extlinux.conf file looks like this: serial 0 57600 0x003 I am using ipmitool to access the console, like so:

Hi, Thanks for your help. On Mon, Nov 11, 2013 at 08:00:47PM -0800, H. Peter Anvin wrote: > There is no reason by Syslinux would reboot the system on a serial > disconnect. There could be a bug, of course; now, Syslinux 4.05 is > pretty old so unless you can reproduce this on a current version that > would be useful. I am using 4.05 because that's what's packaged in the

We have recently been asked to evaluate some computing machinery for a new project. This particular end user has very limited experience with the stated security requirements in a lights-out environment. Their primary work (as well as mine) in the past has been with very small, simple networks of desktop machines and a few servers with extremely limited access.? For the most part, their admins

Hi John, Thanks for the explanation. I looked at the BIOS and found the following where the pseudo MAC address is from: ################################################################################ Planar Ether 1 MAC Address: E4:1F:13:77:16:5F ============> This is shown in ifconfig eth0 Planar Ether 2 MAC Address: E4:1F:13:77:16:60 ============> This is shown in ifconfig eth1 BMC