similar to: PJSIP Losing knowledge of external_media_address

On Fri, Aug 18, 2023 at 1:09 PM Mark Murawski <markm-lists at intellasoft.net> wrote: > I've seen this happen three times in the wild now. I've been trying to > isolate the source of the issue, but so far it seems like there's not > enough debug output to know why this occurs. > > Long story short: > - Start Asterisk > - PJSIP Handles receiving INVITE from

Ok Dan, try this... I was able to get this to work behind a NAT and with ip address authentication. [global] type = global debug = yes [transport1] type = transport bind = 0.0.0.0 protocol = udp *local_net=<yourlocalnet I.E. 10.10.10.10/24 <http://10.10.10.10/24>>external_media_address=<your public ip address>external_signaling_address=<your public address>*

On Mon, Dec 15, 2014 at 9:48 PM, Dan Cropp <dan at amtelco.com> wrote: > > Thanks George. > > I will correct my local_net in the morning. > > Vitelity chan_sip settings I have working, do not have a fromuser. > sip.conf settings... > > I think you can actually specify anything, it just has to be populated with something other than a sub-account username. >

Hello Steve, use the following configuration for the transport and bind this transport to the trunk: [transport_name] type=transport protocol=tls bind=192.168.13.24 ; your bind IP ca_list_file=/etc/pki/tls/certs/ca-bundle.crt ; method=tlsv1_2 verify_server=yes allow_reload=no ;tos=0xb8 ;cos=3 external_media_address=your.ext.host.name ; hostname pointing to your ext. IP

On Mon, Dec 15, 2014 at 7:34 PM, Dan Cropp <dan at amtelco.com> wrote: > > I am not sure if I entered the correct settings for the transport > information. > > For the local_net, I entered my local ip address, but no mask. I will > check with the network admin so he can verify the settings I entered. > > > You need the network and mask. For example if the ip

Thanks, Michael. A few questions: Is [transport_name] a reserved word, or am I supposed to replace it with a name of my own, like '[did-transport]'? Some of the keywords I haven't seen before. Is ca_list_file supposed to be an aggregate of the public and private key? And what are the 'method,' 'tos' and 'cos' keywords, which are commented out in your

I'm quite new to Asterisk and using Asterisk 13 on FreeBSD current. Asterisk is behind a NAT router, the physical setup is very much a trivial one. The Asterisk PBX is supposed to act as the telephone gateway for several VoIP/SIP phones. I'm using throughout pjsip as configuration, I have no experience with chan_sip since I started recently using Asterisk for several SoHo and lab's

Scenario: Our Asterisk 13 PBX (on network 192.168.254.0/24, bound to 192.168.254.1:5060) is behind a NAT, acting as a client to our ITSPs SIP server. But also, this Asterisk is server for various VoIP telephones. Acoording to Asterisk's wiki, the transport section of pjsip.conf is configured as follows: ; Transport via UDP [transport-nat-udp] type= transport

Thank you for the response Joshua . I had rtp_symmetric=yes before I wrote the email, then I set it to no, restart asterisk, and tried to make the call from the remote endpoint again but still tcpdump is showing me the RTP packets are being sent from Asterisk to the private IP. tcpdump on asterisk server showing UDP packet bound for my remote endpoints internal IP: 17:07:57.130212 IP

Hello All, I have an Asterisk server v13.1.0 running on EC2 and I am able to connect and register SIP devices and "see" them on the asterisk CLI. I am also able to place calls, but I am not able to hear any audio on either end after the call is picked up. I was wondering if you can tell me what a minimal configuration for Asterisk on EC2 looks like. My current pjsip.conf configuration

I want to configure communication with my phone provider using TLS for all the obvious reasons. Since I'm behind a firewall, I'll be needing to do it with NAT. There are examples of UDP plus NAT in pjsip.conf, but none for TLS plus NAT. Would it be correct to set up the TLS transport stanza to look like the [transport-udp-nat] stanza example, replacing UDP with TLS in lines like

Hi guys, have really annoying problem with trunks when I calling over voip provider.. after awhile provider sends INFO packages but for some reason Asterisk doesn?t answer on it. after 8 packagers provider just drops the call, here is the package <--- Received SIP request (555 bytes) from UDP:192.168.53.1:5060 ---> INFO sip:c2e74184-4d23-43a3-8fd9-26ba2c5ef6c9 at 192.168.53.9:5060 SIP/2.0

I've split this thread off from another (PJSIP authentication) because I think the root cause is something different. I think the problem is the following FROM line in my SIP INVITE transaction: From: "MYNAME" <sip:16667778888 at 172.31.253.4>;tag=773a3e6a-a677-4fb1-95fc-54b379b650a4 The IP address above is an internal/non-routable IP, so Twilio is rejecting it. For some

Hey guys,tried to make tls work with pjsip on asterisk 13.2.0 have compiled pjsip with ssl, added transport [tls] type=transport cert_file=/pbx/keys/server.crt ca_list_file=/pbx/keys/ca.key priv_key_file=/pbx/keys/server.key protocol=tls bind=192.168.1.4:5061 local_net=192.168.1.0/24 external_media_address=77.77.77.77 external_signaling_address=77.77.77.77 have configured Grandstream GXP1400

You need to put your external IP in the transport configuration: external_media_address=X.X.X.X external_signaling_address=X.X.X.X external_signaling_port=5060 On 21/06/23 12:36, TTT wrote: > I've split this thread off from another (PJSIP authentication) because I think the root cause is something different. I think the problem is the following FROM line in my SIP INVITE transaction:

On Thu, Sep 15, 2016 at 8:38 AM, Madushan Geethanga <mgliyanage.rc at gmail.com > wrote: > Hi, > > Thanks for the reply. > > Yes my PABX is on the cloud when I try to register to the server, the > server sends registration OK with public address but OPTION method > includes the private address of the server in from header not the public > address. I have include

I corrected my local_net setting (based on advice from network admin). I have tried several different values for the from_user and still have the same problem. Asterisk receives the OK from Vitelity. Asterisk sends the ACK (without a Contact header). Vitelity doesn?t seem to process it, so they send an OK again. The OK receive, Transmit ACK occurs 4 times. A short while later, Vitelity hangs up

On Fri, Sep 16, 2016 at 5:55 AM, Madushan Geethanga <mgliyanage.rc at gmail.com > wrote: > Hi, > > Tried with both softphone (Ekiga) and snom IP phone, contact header > contains the public IP. but from header contains the private IP. after > OPTIONS method sent by the server. client sends an Register with expires 0. > Ok, did setting from_domain work? > > Best

On Thu, Sep 15, 2016 at 7:17 AM, Faheem Muhammad <faheem2084 at gmail.com> wrote: > > > On Wednesday, 14 September 2016, Madushan Geethanga < > mgliyanage.rc at gmail.com> wrote: > >> Hi, >> >> What is the equal option for externip in asterisk 13 with pjsip. I have >> tried >> >> external_media_address=XX.XX.XX.XX >>

Thanks George. I will correct my local_net in the morning. Vitelity chan_sip settings I have working, do not have a fromuser. sip.conf settings... [HVout] type=friend dtmfmode=auto host=64.2.142.93 disallow=all allow=ulaw canreinvite=no trustrpid=yes sendrpid=yes nat=yes context=TestApp On Dec 15, 2014, at 9:32 PM, George Joseph <george.joseph at fairview5.com<mailto:george.joseph at