similar to: CentOS on Fujitsu Hardware

Alle, I am trying to install CentOS 5 on a Dual Xeon 5160 FJ RX200 S3. The RAID hardware is an internal LSI MPT 1068 SAS/RAID controller (LSI 1068SASIME-2300). I have downloaded the drivers (mptsas, mptscsih and mptbase) and created the required floppy. When I run linux dd after booting from either the DVD or Disk 1 of the CentOS distro, it says it loads mptsas, mptbase and mptscsih and

Alle, Our customer is looking for a drive with the following specs that works (but is not necessarily supported by the vendor, that would be gravy) on CentOS4/5: DVD hyper multidrive, capable of reading and writing DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD-R for DL, and DVD+R DL. The HP DVD940e (USB 2.0, but that is *not* a requirement,

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi, anybody has experience with ${subject} server (intel E7520 based)? I red some incompatible problems with new intel mb chipsets and digium cards, but I don't remember which chipsets on black list. A -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 189 bytes Desc: This is a digitally signed message part

Hi, I've recently benchmarked btrfs v0.11 & v0.12 against ext2, ext3, ext4, jfs, reiserfs and xfs. OS: Ubuntu Hardy Kernel: 2.6.24(-5-server) Hardware: --------- Fu-Si Primergy RX330 S1 * AMD Opteron 2210 1.8 GHz * 1 GB RAM * 3 x 73 GB, 3Gb/s, hot plug, 10k rpm, 3.5" SAS HDD * LSI RAID 128 MB Fu-Si Econel 200 * Intel Xeon 5110 * 512 MB RAM

Hello everybody, I'm looking for some insights on reproductible lockups with this server so please bear the long description that follows: Installed the 4.0 Centos than yum updated it so it results a 4.2 Centos fully updated. During the instalation and update there were no cold boots. That's important because if (updated Centos or not) you cold boot the server it stucks at the

Hi All, I have an "appliance" cd which uses CentOS 4.0 (Final) which I am trying to load on a new Dell 1950 server with a SAS driver controller. During the install it fails to find any disks to load to. I got the drivers from Dell and dd the correct one to a floppy, boot from the appliance cd and enter linux dd at the prompt. I load the driver in the install and it still fails to find

Alle, Has anyone gotten Zimbra to work on an installation of CentOS4.3, x86_64 architecture? I have tried to install the RHEL4 3.1.4 32-bit version with the following error: Found zimbra-core Error: attempting to install i386 packages on a x86_64 OS. Exiting... Shouldn't this work with 32-bit compat? I've also tried to install RHEL4_64 4.0.0.RC1 but post installation fails when

Alle, We're running Dovecot V1.0.7 on RHEL5.5, using maildir. We would like to user per user quotas with an OpenLDAP (V2.3.43) backend. We have setup a default quota in /etc/dovecot.conf: quota = maildir:storage=10240:ignore=Trash And have the following userdb configs in /etc/doveconf.conf: userdb ldap { args = /etc/dovecot-ldap.conf } and the following user_attrs defined in

Alle, I have a major problem. I'm running CentOS 5.5 on some rather old hardware (Dual Celeron 500MHz with 768MB of memory). Sometime in the last week, the DB became corrupted (I noticed when yum update would hang). I've tried running rpm --rebuild with both the 2.6.18-194.17.4 and 2.6.18-194.26.1 kernels and get a segmentation fault each time. Consequently, I'm pretty much stuck

Alle, Does anyone know if there is/where to get an rpm of flow-tools V0.66 or better for CentOS/RHEL 5.3? We've been trying to build from the SRPM @ http://cng.ateneo.net/cng/wyu/software/srpm/flow-tools-0.68-2.src.rpm with no luck. Best Regards, Camron -- Camron W. Fox Hilo Office High Performance Computing Group Fujitsu Management Services of America, Inc. E-mail: cwfox at

Alle, We currently have a CentOS 5.6 x86-64 server running using about 70G of a 500GB hardware raid partition. We'd like to install 6.0 alongside this installation in a dual boot configuration. We tried to install using the "Use Free Space" installation option, but the installer did not see the 475G of unused space. Is there any good way to do this, or is it even feasible? Best

Alle, We recently received a requirement to implement a KB/FAQ solution that must: Web based Be searchable Allow registration of users Keep a history of user queries Allow new queries sent to subject matter experts via email and receive email updates when answers have been posted. Something along the lines of what CAP does using RightNow. Does anyone have any opensource suggestions for this

Alle, I have installed and enabled (I think) the yum protectbase plugin: [cwfox at lurker ~]$ rpm -qa | grep -i protectbase yum-plugin-protectbase-1.1-1.c4 [cwfox at lurker ~]$ cat /etc/yum/pluginconf.d/protectbase.conf [main] enabled = 1 [cwfox at lurker ~]$ grep plugin /etc/yum.conf plugins=1 [cwfox at lurker ~]$ cat /etc/yum.repos.d/CentOS-Base.repo <SNIP> [base]

Alle, Can't get on IRC or I would have asked there. Are there any plans to add a Horde-Apps groups to the extras repository like there is for CentOS4? Best Regards, Camron -- Camron W. Fox Hilo Office High Performance Computing Group Fujitsu America, INC. E-mail: cwfox at us.fujitsu.com

Alle, Does anyone have any experience with with Netgear WG511v2 cards and V4.4? I read the post @ http://www.centos.org/modules/newbb/viewtopic.php?topic_id=4600&forum=30&post_id=13268#forumpost13268 but the system doesn't even seem to see the card. "/sbin/cardctl ident" shows no info on slot 0/1. "/sbin/modprobe prism54" comes back with nothing. I thought

Alle, We're trying to install kvm on a newly update CentOS5.4 box. Which package should /usr/bin/qemu-img come from, kvm-qemu-img or qemu? When we try to install kvm\* we get the following error: Transaction Check Error: file /usr/bin/qemu-img from install of kvm-qemu-img-83-105.el5.x86_64 conflicts with file from package qemu-0.9.0-4.x86_64 file /usr/share/man/man1/qemu-img.1.gz

Alle, I have an HP L7780 MFP, which is supported under hplip 1.7.2 but not the current install of 1.6.7. Does anyone know of a way just to add that particular driver to 1.6.7, or will it require removing the standard 1.6.7 and doing a custom install of 1.7.2. If the latter, what would you consider the dangers/other implications of going "rogue"? Best Regards, Camron -- Camron W.

Alle, Here is our situation: Our customer leases their machines from us and contract us to to manage them (as far as all systems administration issues). The customer does not have root access to any machine (by their own choice, as they want us to be responsible if something goes awry). In the case of their web servers, we handle all configuration, they manage the content. We make changes

Alle, We have recently had one of our office servers go south. The hardware was an Intel SDS2 motherboard (EATX), Dual Intel PIII 1.4GHz FC-PGA2-L2 512KB, 3GB (6x512MB) 168 pin DIMM, SDRAM 133MHz/PC-133-ECC with 1x3Ware 7006-2 and 2x3Ware 7506-4LP RAID controllers. The OS was RHEL3. Apparently, according to the beep codes, there has been an FRB failure. I've migrated most of the