similar to: Sending notification when zpool replace has finished resilvering?

Hi! We have a raidz2 pool with 1 spare. Recently, one of the drives generated a lot of checksum errors, so it was automatically replaced with the spare. Since the errors stopped at some point, we figured that the drive itself was not at fault. We offlined it, zeroed it and onlined it again, started resilvering, and manually detached the spare drive. The zpool status is ONLINE and mentions

I know this topic has been discussed many times... but what the hell makes zpool resilvering so slow? I''m running OpenSolaris 2009.06. I have had a large number of problematic disks due to a bad production batch, leading me to resilver quite a few times, progressively replacing each disk as it dies (and now preemptively removing disks.) My complaint is that resilvering ends up

i''ve got a little zpool with a naughty raidz vdev that won''t take a replacement that as far as i can tell should be adequate. a history: this could well be some bizarro edge case, as the pool doesn''t have the cleanest lineage. initial creation happened on NexentaCP inside vmware in linux. i had given the virtual machine raw device access to 4 500gb drives and 1 ~200gb

I have a situation where my zpool (with two radiz2s) is resilvering and reaches a certain point, then starts over. There no read, write or checksum errors. The disks do have a fair amount of resilvering to do, as I''ve had a variety of disk failures. But at the core of things, there''s enough parity data to avoid data loss, and the zpool is functioning fine, albeit in a

Dear all Is there a way to stop a running scrub on a zfs pool? Same question applies to a running resilver. Both render our fileserver unusable due to massive CPU load so we''d like to postpone them. In the docs it says that resilvering and scrubbing survive a reboot, so I am not even sure if a reboot would stop scrubbing or resilvering. Any help greatly appreciated! Cheers, Thomas

Hey folks, This might be a daft idea, but is there any way to shut down solaris / zfs without flushing the slog device? The reason I ask is that we''re planning to use mirrored nvram slogs, and in the long term hope to use a pair of 80GB ioDrives. I''d like to have a large amount of that reserved for write cache (potentially 20-30GB), to facilitate rapid suspend to disk of

I''ve got a Thumper running snv_57 and a large ZFS pool. I recently noticed a drive throwing some read errors, so I did the right thing and zfs replaced it with a spare. Everything went well, but the resilvering process seems to be taking an eternity: # zpool status pool: bigpool state: ONLINE status: One or more devices has experienced an unrecoverable error. An attempt was

Hi, I have Dell md1200 connected to two heads ( Dell R710 ). The heads have Perc H800 card and drives are configured in Raid0 ( Virtual Disk) in the RAID controller. One of the drives had crashed and is replaced by a spare. Resilvering was triggered but fails to complete due to drives going offline. I have to reboot the head ( R710) and drives comes online. This happened repeatedly when

I''ve got a zpool that has 4 raidz2 vdevs each with 4 disks (750GB), plus 4 spares. At one point 2 disks failed (in different vdevs). The message in /var/adm/messages for the disks were ''device busy too long''. Then SMF printed this message: Nov 23 04:23:51 x.x.com EVENT-TIME: Fri Nov 23 04:23:51 EST 2007 Nov 23 04:23:51 x.x.com PLATFORM: Sun Fire X4200 M2, CSN:

I have a zpool of five 1.5TB disks in raidz1. They are on c?t?d?p0 devices - using the full disk, not any slice or partition, because the pool was created in zfs-fuse in linux and no partition tables were ever created. (for the full saga of my move from that to opensolaris, anyone who missed out on the fun can read the thread http://www.mail-archive.com/zfs-discuss at opensolaris.org/msg34813.html

Hello, I''m working with someone who replaced a failed 1TB drive (50% utilized), on an X4540 running OS build 134, and I think something must be wrong. Last Tuesday afternoon, zpool status reported: scrub: resilver in progress for 306h0m, 63.87% done, 173h7m to go and a week being 168 hours, that put completion at sometime tomorrow night. However, he just reported zpool status shows:

Hi all, I am running S11 on a Dell PE650. It has 5 zpools attached that are made out of 240 drives, connected via fibre. On thursday all of the sudden two out of three zpools on one FC channel showed numerous errors and one of them showed this: root at solaris11a:~# zpool status vsmPool01 pool: vsmPool01 state: SUSPENDED status: One or more devices is currently being resilvered. The pool

Is there any way to control the resliver speed? Having attached a third disk to a mirror (so I can replace the other disks with larger ones) the resilver goes at a fraction of the speed of the same operation using disk suite. However it still renders the system pretty much unusable for anything else. So I would like to control the rate of the resilver. Either slow it down a lot so that the

Just look at this. I thought all the restarting resilver bugs were fixed, but it looks like something odd is still happening at the start: Status immediately after starting resilver: # zpool status pool: rc-pool state: DEGRADED status: One or more devices has experienced an unrecoverable error. An attempt was made to correct the error. Applications are unaffected. action: Determine

When I booted my laptop up this morning it took much longer than normal and there was a lot of disk activity even after I logged in. A quick use of dtrace and iostat revealed that all the writes were to the zpool. I ran zpool status and found that the pool was resilvering. Strange thing is that while the pool is a mirror, one side of it is offline since it is on an external usb disk - which

I had a drive fail and replaced it with a new drive,During the resilvering process,that show "Too many errors",and process fail. now,the pool can online,but cannot accept any zfs''s commands that change pool''s state,I can list File directory,but don''t mv?cp and rm -f. what can I do,I need that data files. root at opensolaris2:~# cat /etc/release

I am curious why zpool status reports a pool to be in the DEGRADED state after a drive in a raidz2 vdev has been successfully replaced. In this particular case drive c0t6d0 was failing so I ran, zpool offline home/c0t6d0 zpool replace home c0t6d0 c8t1d0 and after the resilvering finished the pool reports a degraded state. Hopefully this is incorrect. At this point is the vdev in question now has

Hello everyone, As one of the steps of improving my ZFS home fileserver (snv_134) I wanted to replace a 1TB disk with a newer one of the same vendor/model/size because this new one has 64MB cache vs. 16MB in the previous one. The removed disk will be use for backups, so I thought it''s better off to have a 64MB cache disk in the on-line pool than in the backup set sitting off-line all

After several days of trying to get a 1.5TB drive to resilver and it continually restarting, I eliminated all of the snapshot-taking facilities which were enabled and 2009-10-29.14:58:41 [internal pool scrub done txg:567780] complete=0 2009-10-29.14:58:41 [internal pool scrub txg:567780] func=1 mintxg=3 maxtxg=567354 2009-10-29.16:52:53 [internal pool scrub done txg:567999] complete=0

Hello All I read this thread Resilver/scrub times? for a few minutes and I have recognize that I dont know the different between Resilvering and Scrubing. Shame on me. :-( I dont find some declarations in the man-pages and I know the command to start scrubing "zpool scrub tank" but what is the command to start resilver and what is the different? -- Best Regards Alexander Dezember, 20