similar to: Remote-Party-ID set to 0 on re-invite using pjsip in Asterisk 16.

On 1 July 2016 at 17:41, Joshua Colp <jcolp at digium.com> wrote: > > >> exten => 1234,Set(CALLERID(all)="Jon Doe" <+123456789>) >> same => n,Dial(PJSIP/phone123, 30) >> > > Your exten line has no priority, is that how it is in your dialplan? > Actually no, I stole that line from an earlier email to this list. Mine has a priority.

Hello all, I'm setting up a couple of test boxes and I'm running into a problem. What I need help with is determining whether I'm going something wrong or if I need to post a bug report. I have two asterisk 13.0-beta 3 machines set up with extensions connected to each as such: 3700 ----> AST-A <------> AST-B <---- 3800 & 3801 When I place a call from 3800 to

On Mon, Dec 15, 2014 at 2:08 PM, Dan Cropp <dan at amtelco.com> wrote: > > Today, I tried the same behavior on Asterisk 13.1.0 and Asterisk 12.2.0. > > > > Same problem is happening with both of them. > > > > Could this be caused by PJPROJECT 2.3? > > > > Anyone have any suggestions for what I can try? > > > > My boss is giving me until

Ok Dan, try this... I was able to get this to work behind a NAT and with ip address authentication. [global] type = global debug = yes [transport1] type = transport bind = 0.0.0.0 protocol = udp *local_net=<yourlocalnet I.E. 10.10.10.10/24 <http://10.10.10.10/24>>external_media_address=<your public ip address>external_signaling_address=<your public address>*

On Mon, Dec 15, 2014 at 3:33 PM, Dan Cropp <dan at amtelco.com> wrote: > > Hi George, > > > > Thank you for looking into this. > > This is behind a nat? > > > Just to be clear...both the pbx and local endpoints are behind the same NAT? > [global] > > type = global > > debug = yes > > > > [transport1] > > type = transport

Not sure why, but Vitelity changed the settings to IP based authentication on me. Here's the new sip.conf settings they sent me. type=friend dtmfmode=auto host=64.2.142.93 allow=all nat=yes canreinvite=no trustrpid=yes sendrpid=yes When I use these settings to originate calls using the sip.conf they sent me, everything works. Action: Originate ActionID: S8 Channel:

On 06/05/2017 at 11:30 AM, Joshua Colp wrote: > On Sun, Jun 4, 2017, at 10:40 AM, Michael Maier wrote: >> On 06/04/2017 at 01:41 PM Telium Technical Support wrote: >>> Just a guess (without knowing about your network), but are the two ends >>> points on public networks and visible to one another? If not the reinvite >>> may be passing an internal (nat'ed)

On Mon, Dec 15, 2014 at 3:54 PM, Dan Cropp <dan at amtelco.com> wrote: > > Yes, everything is behind the same NAT. > > > > For the application I?m working on, the only endpoint is the endpoint to > Vitelity. > > We use AMI to Originate calls from Asterisk endpoint through Vitelity to > phones. > > After that, we control the call through AMI to perform the

Here's an update... My network admin would not turn off the ALG because it would cause several other problems to other phone systems we have. He looked at the sip trace. What he found is the PJSIP trace showed a different IP address than the older chan_sip so he had me change the aor contact to outbound.vitelity.net At this point, it seems to be working (and this is going through a Cisco

Asterisk 13.8 Is CALLERID(all) supposed to wok for pjsip? When I do this: exten => 1234,Set(CALLERID(all)="Jon Doe" <+123456789>) same => n,Dial(PJSIP/phone123, 30) I expect the callerid to be as set, but is always seems to be "phone123", the name of the endpoint. Andrew -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello! Oh, wise ones, ponder with me over two of the surprises that populate the universe! I have a phone, that I sometimes cannot reach, connected via pjsip. It can call other extensions just fine, it can call out over a trunk to my cell, all is well, but getting a call? Forget it most of the time. Here is all the config relevant to that phone: [murftest12] type=aor qualify_frequency=1992

Dan Cropp wrote: > I corrected my local_net setting (based on advice from network admin). > > I have tried several different values for the from_user and still have > the same problem. > > Asterisk receives the OK from Vitelity. > > Asterisk sends the ACK (without a Contact header). A Contact header is not required to be in the ACK. > > Vitelity doesn?t seem to

On Mon, Dec 15, 2014 at 7:34 PM, Dan Cropp <dan at amtelco.com> wrote: > > I am not sure if I entered the correct settings for the transport > information. > > For the local_net, I entered my local ip address, but no mask. I will > check with the network admin so he can verify the settings I entered. > > > You need the network and mask. For example if the ip

I've seen this happen three times in the wild now.  I've been trying to isolate the source of the issue, but so far it seems like there's not enough debug output to know why this occurs. Long story short: - Start Asterisk - PJSIP Handles receiving INVITE from ITSP via WAN (Asterisk is behind NAT).  SIP is handled correctly, Asterisk responds OK with RTP media address of

On Mon, Dec 15, 2014 at 9:48 PM, Dan Cropp <dan at amtelco.com> wrote: > > Thanks George. > > I will correct my local_net in the morning. > > Vitelity chan_sip settings I have working, do not have a fromuser. > sip.conf settings... > > I think you can actually specify anything, it just has to be populated with something other than a sub-account username. >

Hello everyone. I allow myself to submit a problem that I can not solve with my VOIP provider Orange in France [2023-06-08 13:19:03] ERROR[185091]: res_pjsip/pjsip_configuration.c:1044 from_user_handler: Error configuring endpoint 'Biv_Sortie' - 'from_user' field contains invalid character '@' [2023-06-08 13:19:03] ERROR[185091]: config_options.c:798 aco_process_var:

Hello! Looks like faq, but... Could you , please, point me on how to convert this [cisco] type=friend host=192.168.22.253 insecure=port,invite to pjsip? as you can see another side is very old cisco router, so I can't change anything there. I don't see any examples here

I have a call coming in. I need to add a SIP Header to the channel. Then, I need to send the call to the Queue so it is sent to the Agent. The SIP header I added, I need to have appear in the INVITE sent to the Agent. It works in chan_sip. I send the call to a macro which does... n,SIPAddHeader(My-Header-Name:${MY-HEADER-VALUE}) n,Queue(${ARG2}) In PJSIP , this doesn't seem to work. Is

I have both the PJSIP add and the chan_sip way of adding SIP headers in there. The Verbose is showing the variable value is there. The INVITE to PJSIP/Agent1 does not include either X-My-DNID or X-My-DNID2 headers. exten => 1234,1,Verbose(X-My-DNID:${MY_DNID}) same => n,Set(X-My-DNID=${MY_DNID}) same => n,Set(PJSIP_HEADER(add,X-My-DNID2)=${MY_DNID}) same => n,Dial(PJSIP/Agent1)

Thanks Scott. I?m taking over for someone else?s code, so I must admit I?m still learning the Agent and Queue concepts. Local channels are something I have not used either. Would local channels essentially be an internal bridge? How would I ?Register Local/number at agent in the queue on behalf of the agent (replace number with the agent's extension number)? From: asterisk-users-bounces