similar to: tcrules ignored? wondershaper integration?

I don''t know whether this is the right place to ask, but kindly point me to an FM that I can R if it isn''t. My wife is creating lots of Kazaa traffic, and I am using rsync to create a full mirror of Red Hat''s FTP site, Aurora Linux FTP site, the LDP site, and some other stuff. Clearly, when one is moving well over 100GB over a 128 Kbps link, this is going to take a

Hi all, I moved wshaper 1.1 cbq file to tcstart, but none of my tcrules are being observed. The only way I can set the marks is by editing the tcstart file. Is there a way to incorporate for tcstart to read and apply my set marks in tcrules? Thank you, ~Andrew Nady.

Season Greetings to all Tom, in your faq, u have this noted: While I am currently using the HTB version of The Wonder Shaper (I just copied wshaper.htb to /etc/shorewall/tcstart and modified it as shown in the Wondershaper README), I treid this with wondershaper, using Bearing Leaf 1.0 stable i even changed the tc command to run_tc, and tried it in both angles, and i receive the following..

So after reading the traffic control documentation at shorewall.net I am a little confused. I don''t understand how to use the tcrules file. What I would ideally like to do is setup htb on a per user basis (either by IP or MAC address). If anybody has any hints on the best way to do this or is willing to explain the use of tcrules file a little better (how I could mark it per IP or MAC)

I''m currently building a firewall for a network with 2 ISP links. Unfortunately, one of the ISP''s doesn''t support BGP yet, otherwise I would be doing load balancing at the router, instead of the firewall. I''ve been trying to find information on how to get WonderShaper working, but everything I''ve found talks about setting it up for a firewall with one

>Miguel Ángel Domínguez Durán wrote: >> Hello again, >> First, excuse me for my poor english. >> I''m trying now to make bandwith control in a firewall machine running >> Shorewall. This machine is also a bridge using bridge-utils >> bridge-utils-devel. It is a mandrake 10. The configuration is something >> like >> this: >> >>

Hi Guys, I''m asking this question again because I have exhausted resources for understanding how to get it to work. I''ve read the howto on getting traffic shaping to work (shorewall''s web site) as well as trying out wondershaper''s htb and cbq scripts. Somehow both does not seem to happen as I want it to. I''ve also read through the lartc

Ok, shaping on Linux is new to me.. so bear with me if i am just stupid. curtain:/etc/shorewall# grep TC shorewall.conf | grep -v ^# TCP_FLAGS_LOG_LEVEL=info TC_ENABLED=Yes CLEAR_TC=Yes TCP_FLAGS_DISPOSITION=DROP curtain:/etc/shorewall# So it should be enabled, right? ---- tcrules ---- 1 eth0 0.0.0.0/0 all 2 eth1 0.0.0.0/0 all 2 eth2 0.0.0.0/0

Hi ! I found an excellent article about QoS and traffic shaping for VoIP (Asterisk IAX protocol), which is designed to improve sound quality even over very busy lines. http://www.howtoforge.com/voip_qos_traffic_shaping_iproute2_asterisk Should I just cut and paste all that to shorewall''s tcrules (replacing 4569 with 5060)? Additionally, author of this article uses IAX protocol,

Following my question: I want to limit all uploading coming from eth1, going to the internet, TCP port 333, to 5kbit. (The recipients in the internet receive the data on port 333) What do I have to add to the tcrules/tcstart files? The situation so far: The Linux PC is connected to the Internet with eth0. I have so far copied the contents of the wshaper.htb file (from The Wonder Shaper) to

Hi everyone, I don''t know if you remember me, but i had a problem with a machine performing bridge (bridge-utils) and firewall (shorewall) duties. I wanted to control traffic in this machine using iproute2 and tc command with the tcstart and tcrules file in shorewall configuration. My machine hanged up when I used my traffic control script that way, but I found a solution :) The key

Having study a number of documents on linux traffic shaper, I started to setup my shaping rules in my network. My linux box is running RH AS3 U3, shorewall 2.0.9. It is using PPPoE connected to the Internet firewall: eth0: connect to the adsl modem eth1: private net ppp0: virtual dial up interface for pppoe There is a ftp server on the private net It is listen for port 21 and configured

(excuse me for my english) why mark range in tcrules is 1-255 ? iptables support marks > 255. Leandro.

Hi there. Currently, our network design has two ISP lines and 3 subnets for LAN. Below are some details :- eth0 - isp1 eth1 - isp2 eth2 - subnet1 eth3 - subnet2 eth4 - subnet3 What i wanted to do is to assign incoming port 80 to our local squid server running on the firewall itself and assigned it to eth0(ISP1). I think it shouldnt be a problem as /etc/shorewall/rules provides a sample of the

Hi, First of all, thanks to all shorewall developers. Shorewall is really great. Here is a patch to add the following feature : This patch allows you to mark packets according to the user name under which the program generating output is running. To do so, the patch will allow you to write rules in the tcrules file looking like that : #MARK SOURCE DEST PROTO PORT(S) CLIENT USER #

Hi All, I have a custom TC configuration where I''m building the tc hierarchy manually with the tcstart script. I also need to add custom iptables rules in the mangle table to classify the packets. Currently I''m using started to insert the iptables commands, but that''s way too late in the process. I tried putting them into the initdone file, but it''s trying to

Just some stuff that was laying around in CVS: 1. Added ''DNAT-'' target. 2. Print policies in ''check'' command. 3. Added CLEAR_TC option. 4. Added SHARED_DIR option. [teastep@wookie Shorewall]$ cat releasenotes.txt This is a minor release of Shorewall that has a couple of new features. New features include: 1) A new ''DNAT-'' action has been

I try use setup traffic shaping with Shorewall-4.0.2 and have fault. When i start Shorewall with tc-files configured i get follow messages: ... RTNETLINK answers: No such file or directory We have an error talking to the kernel ERROR: Command "tc filter add dev eth2 parent ffff: protocol ip prio 50 u32 match ip src 0.0.0.0/0 police rate 500kbit burst 10k drop flowid :1" Failed

Hi Folks, I''m a new user to Shorewall, it came installed on the redWall firewall that I am using and I''m really happy with both projects! Thanks for all your work on it! I have a question about tcrules and $FW. I''m doing source policy routing and need to be able to add an output rule to the mangle chain with a source that is specific network, not 0.0.0.0/0. It

Hello everyone. I''ve been trying to get Qos to work here for two days now, but it REALLY doesn''t seem to work the way I want to. Here is my situation: Internet Wireless LAN Firewall DMZ Local lan As you can see, I got a Debian box in the middle as my firewall with 3 network interfaces and a wireless one. I use