similar to: Traffic Shaping using Shorewall and WonderShaper

I have wondershaper to limit my upload at 400kilobits (my line is 600kbps). I do a lot of torrent seeding and I dont want my pings killed when I''m uploading so I set low prority source ports as follows (by the way, I have bittornet to only use ports 6881-6910): NOPRIOPORTSRC="6881 6882 6883 6884 6885 6886 6887 6888 6889 6890 6891 6892 6893 6894 6895 6896 6897 6898 6899 6900 6901

Hi, I have a question conercing wondershaper. I''m using the Clarkconnect linux distribution for my linux router and I tried to use wondershaper. On start up of wshaper, there are no errors or any other problems but I''m not sure if it''s running correctly. Only one qdisc / one class is used and when I start an uplink ftp transfer, my ping time is growing up to 1700ms - I

Hi all, ive got wondershaper working well with the highest download while maintaing minimal latency but the problem is this: ive got 2 nics in the linux router eth0 and eth1. eth1= internet interface but this is connected to a router say 10.0.0.190, now off that router there are other servers, mail server, domino server etc now if i shape on eth1 ingress and egress using the wondershaper script

Hello, i´ve installed a Suse 8.1 minimal System with iproute 2.4.7 and iptables, Suse default Kernel 2.4.19. When I start the Wondershaper 1.1a Script I get the following Error: CBQ: "allot" is required to set WRR parameters. /home/skripte/./wshaper: line 72: allot: command not found CBQ: "allot" is required to set WRR parameters. /home/skripte/./wshaper: line 78: allot:

Hi ! I´ve been using the wonderful wondershaper from chapter 15.8 of the LARTC Howto for some time. It´s really wonderful. Actually, I use the version from http://freshmeat.net/projects/wshaper/?topic_id=87 Now I tried to put some hosts to low priority, and it doesn´t work. The traffic is splitted equally between the noprio and the other hosts. Is this because I use ip masquerading, and all

Hi, first of all, let me thank you for your great Shoreline Firewall. I use it with great success at home (protecting my WiFi connection). And now if I could have a question about traffic shaping. I did read everything I could find but I still have two problems: first, the MARK from tcrules is not working in HTB based simple tc filter line ("handle $MARK fw classid 1:20"). If I switch

Season Greetings to all Tom, in your faq, u have this noted: While I am currently using the HTB version of The Wonder Shaper (I just copied wshaper.htb to /etc/shorewall/tcstart and modified it as shown in the Wondershaper README), I treid this with wondershaper, using Bearing Leaf 1.0 stable i even changed the tc command to run_tc, and tried it in both angles, and i receive the following..

I''m having a network inside of a dsl modem and I''m using wondershaper on the computers to be able to surf while bulk downloading. The problem is that also the internal traffic is shaped, which means the internal network is at 200kb/s, instead of 100Mb/s. Is there a way to exclude the internal adresses from the wondershaper rules, or is there any other good way to solve this?

Hello! I want to give port 14567 a high priority/minumum delay because its a onlien game. I took wondershaper cause its fairly easy to understand. AND i read the HowTo, especially Section 9!! DOWNLINK=786 UPLINK=128 DEV=ppp0 # start filters # TOS Minimum Delay (ssh, NOT scp) in 1:10: tc filter add dev $DEV parent 1:0 protocol ip prio 10 u32 \ match ip tos 0x10 0xff flowid 1:10 Then i

Hi, I really like the wondershaper script, it works very well for me. My question is this. Is there a way to get certain remote hosts to be excluded from the shaping? I ask because I don''t have my box connected directly through the net. It sits behind a nat device, and has ports forwarded in for services. I''d like to limit the ports and services, but only to things going outside

I''m trying to shape traffic on a Devil-Linux box. This note was originally sent to their maillist, because the LARTC list appears to have been down for the past few days. My mailbox was just flooded with a half dozen or so confirmation requests in response to my repeated attempts to subscribe to this list. ---------- Forwarded message ---------- From: drew einhorn

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! when I activate wondershaper on my dsl connection (pppoa vc mux), i get three errors: # sh -x /usr/sbin/wshaper ppp0 + /usr/sbin/xmlstarter setenv tc_downlink + DOWNLINK= + /usr/sbin/xmlstarter setenv tc_uplink + UPLINK= + [ -z ] + cat /proc/avalanche/avsar_modem_stats + grep Connection Rate + awk {printf("%d", $8)} +

Hi, When i do ''wshaper start'' the interface i have defined stops routing traffic for some reason. It resumes routing when i do ''wshaper stop''. I''m using debian stable (3.0 woody) with debian''s default 2.4.18-686 kernel. When I run the script I get no errors, and when I do a ''status'', everything looks correct. Can ANYONE

Hi I am very unclear about the wonder shaper and a bit of a novice with Unix all together I have a question for you and I hope you can answer Basically my office is getting a couple of people slowing down the network so ive been looking around and found wondershaper What I want to know is that can I rather than having low priority ports have it with high priority ports And

I don''t know whether this is the right place to ask, but kindly point me to an FM that I can R if it isn''t. My wife is creating lots of Kazaa traffic, and I am using rsync to create a full mirror of Red Hat''s FTP site, Aurora Linux FTP site, the LDP site, and some other stuff. Clearly, when one is moving well over 100GB over a 128 Kbps link, this is going to take a

Hi, I just installed wondershapper 1.1a on my ipcop firewall box. I have roadrunner cable with a ftp server setup. My download speed is 2mbit (I get 225 KBytes) and my upload is 384kbit (I send at 43 KBytes). What should the settings in wshaper? I can ping yahoo.com at 90msec with little traffic.....and at around 220msec with full upload traffic. Mark

Hello, I am trying wondershaper-1.1a on a friend''s pppoe connection on her Linux box. There are a few things I don''t understand. 1. She has pppoe connection so should DEV=eth0 or DEV=ppp0 ? 2. Her ISP just says on her payment bill that the speed is 128kbps, but doesn''t mention any downlink/uplink speed, so in that case what should be, DOWNLINK= and UPLINK= ? 3. She

Hi all, I moved wshaper 1.1 cbq file to tcstart, but none of my tcrules are being observed. The only way I can set the marks is by editing the tcstart file. Is there a way to incorporate for tcstart to read and apply my set marks in tcrules? Thank you, ~Andrew Nady.

greetings all, i''ve searched high and low for this, but can''t seem to find an answer anywhere.. having read the docs and the wondershaper script itself, it occurred to me that the documentation promises an immediate drop in interactive app latency, specifically mentioning SSH as a big winner. however, looking through the script i can''t really tell just *how*

Hi everybody! I know this discussion list isn´t just about wondershaper, but i think someone can help me. I used to have a linux box running red hat 8, as firewall on my lan. I upgraded to debian 3.0 and tried to use the same wondershaper files under debian, but, when i run wondershaper on ppp0 device, it just stops transfering. Remember: its the same files i used with success under red hat 8.