similar to: help with multiple IP over pppoe

Hola, Can someone please point me to the right direction on how-to set up proper routing on PPPoE connection and multiple external IP''s. Thank you kindly. ~Andrew Nady.

I have a requirement which I guess it is not too unusually, however I haven''t quite figured out how to do it and couldn''t find any examples which handle that. I have made myself a Linux-based bridge, eth0 bridged with eth1 to form br0. In this bridge, I run ''tc'' script to handle QoS. So far nothing unusual. However, what''s different is that this

My Internet gateway is using ADSL PPPoE connection with dynamic public IP assigned by ISP. My Internet gateway is Redhat AS3 U2, shorewall 2.0.9 As my ISP provided 4 simultaneous pppoe dailup connection for the same physical adsl line. My linux server can be configured for multiple pppoe connection i.e. ppp0, ppp1, ppp2, ppp3 Is it possible of shorewall to assigned say ppp0''s IP is

hi all. i am currently now serving PPPoE in my area. i had a script generated from tcng that worked perfectly before i started serving PPPoE. the issue is not in the script it self BUT in that "tc" code is not shaping on the ethernet anymore BUT INSTEAD on the pppX devices. I tested it and talking jargon, what should i do? The issue is that for each PPPoE login, PPPoE-server

I need some suggestions, I want to limit the up and down bandwidth of PPPoE users that are terminated on a Linux router (kernel 2.6). What are my options, can I apply tbf qdisc on a ppp interface? That would limit the download, what about the upload? Any suggestions are welcome. -- damjan | дамјан This is my jabber ID --> damjan@bagra.net.mk <-- not my mail address!!!

I am a newbie to linux and shorewall. I am reading the shoreall quickstart guides. I am a bit confused about the following statement: ----------- quote -------------- The firewall has two network interfaces. Where Internet connectivity is through a cable or DSL "Modem", the External Interface will be the ethernet adapter that is connected to that "Modem" (e.g., eth0) unless you

My provider is getting ready to switch my DSL router to bridging mode and I supply the router (so I can get no only IPv4 addresses but also IPv6 addresses!). Here are his 'instructions' to me: "Basically you start pppoe, I give you the username and password for it, and then I set the router to passthrough modem mode, and you initiate the PPPoE session directly with my LNS back

Greetings, I've just upgrade a home server to CentOS 6.5 with a new dual-core processor and mobo. I see that with the CentOS 6.x release rp-pppoe can be run as a daemon. I've looked through some online one-page setup notes for rp-pppoe, but nowhere is there a discussion of running it as a daemon. Until now, I've cobbled an ifcfg-ppp0 file and placed it in

helo again. I think this question i am asking is worth: we know that pppoe-server creates a pppX device on each connection done to it. So, when i have to shape, i have to shape each pppX connection device on itself alone. What i know is that the borrowing method on one device by itself, e.g. ppp0, alone using HTB or the like. this means that i have to create for another device, e.g. ppp1,

Hi all, I have a little problem with my home-made slackware linux server. Here is the scenario: 1. I have a local wifi network 2. my server do masquerading and exit in internet via a PPPoE connection Goals: 1. not use SQUID 2. shaping the traffic with classes 3. emule connection must have minimum priority and a band-limit of 10KBytes/s in uplink (server--->internet) Any idea? Thx, Diego --

Hello, My system is: Server with Slackware 8.1 LINUX, ADSL Internet with PPPoE connection, and I masquerade my LAN. I use "Roaring Penguin" PPPoE client for my ADSL connection. I would like to connect another ADSL line (also PPPoE) to my server and have two lines, because I want to make "Simple source policy routing", as described in LARTC HOWTO. How should I set up my

I need basic PPPoE startup help. adsl-start DID bring up my PPPoE link (ppp0) to my ISP over eth0 via the DSL modem/bridge. My IPv4 CIDR block is routing and Shorewall is doing the firewalling. But shorewall has to be started after ppp0 is up and working. For now this means running shorewall restart (or start?). Shorewall 4.2 will have a way to restart shorewall without recompiling, I

Hi, I have been a shorewall user for a long time now, and it has been working flawlessly. I have now changed ISP and my new DSL connection is PPPoE. My setup is as follows: internet <--------> 3com812 Officeconnect (bridge mode) <----> eth0 <-------> linux box <----> eth1, eth2, eth3, eth4 <---> other internal networks Things are working fine, but the link is

Hi all I get a Cisco 1841 router, connecting the office through a CHAP PPPoE link: [...] interface Dialer1 ip address negotiated ip mtu 1492 ip nat outside ip virtual-reassembly encapsulation ppp ip tcp adjust-mss 1452 dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap callin ppp chap hostname username at isp ppp chap password 0 s0meStr0ngP4sswd [...] As

I am building a CentOS 5 box to ship to Houston which will be a gateway system on an SBC DSL connection for a while until the client gets a T1 installed. I have read up on using adsl-setup and related software, but never done PPPoE on anything but LinkSys commodity boxes. I have examined the adsl-setup script, and I think I understand how this works, but want to be sure I understand things

My telco is moving to feeding me over fiber, breaking out with a media converter to one Ethernet interface. At present, I am retaining the static feed over copper on eth0, and taking the two new feeds via vlans on eth1. I have configured the static IP feed on eth1:790 as vlan 790, and that seems to be fine, and eth1:780 as the PPPOE feed, and brought up PPPOE to give me an IP, that is

Hi, I have a PPPoE server running on a linux box that accepts multiple PPPoE sessions from clients. I'd like to bridge each of the sessions together so that it looks like just one interface. Below is a diagram: br0 | ------------------------------- | | | | ppp0 ppp1 eth3 ppp3 I've read that anything can be bridge as long as MTU is the same.

I have three ADSL lines that I''d like to use as one big pipe to the internet. The ADSL service works by establishing a pppoe connection (the ADSL "modem" is a bridge), and each pppoe interface gets its own IP address. This means I''d have to have 4 ethernet interfaces (3 for each of the ADSL modems and 1 for the LAN) in my gateway. I''d setup the gateway to NAT

Hi all, I'm trying out bridging for my wireless and wired LAN, so that they can both use my PPPoE connection. Here's the network structure, pretty easy: darjeeling (192.168.1.7) ringo (192.168.1.3) (mtu 1500) (mtu 1500) \ / \ wlan0 <--br0 (mtu 1500)--> eth1

Peter Jakobi wrote: > Hi Jiri, > > you already tested an ancient userspace-only rp-pppoe? > I''ve still one active, and trying this you could validate > your the rest of your setup, before looking at possible > kernel changes anew (strace, ltrace, logs, whatever)... > Hi Peter. No I did not. Do I have to compile it? Can you give me more info what to do?