similar to: Accounting and MRTG

I am not a member of the mailing list. Shorewall version 2.0.9 ip addr show 1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 brd 127.255.255.255 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 4: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000

You are awesome!!!! -----Original Message----- From: shorewall-users-bounces@lists.shorewall.net [mailto:shorewall-users-bounces@lists.shorewall.net] On Behalf Of Tom Eastep Sent: Wednesday, March 30, 2005 9:11 AM To: Mailing List for Shorewall Users Subject: Re: [Shorewall-users] Shorewall and an inline IDS (snort-inlineorhogwash) Tom Eastep wrote: > Thibodeau, Jamie L. wrote: >

Does anyone know what a good maximum number of machines I should place in the ProxyArp list? Thanks Jamie

Has anyone successfully setup a shorewall Ucarp solution?

If I''m using proxyarp and I try to ping that host from a machine in the net(untrusted) zone should I get a reply from the firewall address saying Destination host unreachable? I would like it to just time out. Jamie

All, I''m trying to do some documentation on the models for our interfaces team. I espcially need them to be able to see the relationships belongs_to and validations. However, I must be stupid with rdoc because I can''t seem to get those two things in the generated documentation. Ideas?

Clients: Some sites just show the top area not the full page. Some sites cant be reached at all. I think it 90% may be the MTU/MSS problem. But I already have set the shorewall.conf CLAMPMSS=1400 or CLAMPMSS=Yes, but it doest make things good. I would be mad. Anybody helps me would so appreciated! If you want know more info. to diag my problem, I would be please to.

On Tue, Sep 6, 2011 at 4:37 PM, Matt Pharr <matt.pharr at gmail.com> wrote: > I'm seeing some behavior that surprised me in writing an <8 x i1> vector to memory and reading it back.  (Specifically, the surprise is that I didn't get the original value back!).  This happens both with TOT and 2.9.  This program illustrates the issue: > > define i32 @foo() { >  %c =

Plus I would like to let you know that it works like a charm. Snort can now see those packets. -----Original Message----- From: shorewall-users-bounces@lists.shorewall.net [mailto:shorewall-users-bounces@lists.shorewall.net] On Behalf Of Thibodeau, Jamie L. Sent: Wednesday, March 30, 2005 9:25 AM To: Mailing List for Shorewall Users Subject: RE: [Shorewall-users] Shorewall and an inline

Hello, I realize that using: x[x > 3 & x < 5] I can fetch all elements between 3 and 5. However I read in from a CSV file, and I would like to fetch all columns from within a range ( 842-2411). In teh past, I have done this to fetch just select few columns: data <- read.csv(filein, header=TRUE, nrows=320, skip=nskip) data_filter <- data[c(2,12,17)]

i''ve installed mrtg to make graphics of the trafic from the interfece throw the snmpd, and the same with ipac witch put iptables accounting rules colect them and store, and gets the output, but the "problem" is that ipac graphics are 3 times smaller that the snmpd. Why??? i did catch all the trafic with ipac so no problem here, and i know that ipac/iptables is at level 3, and

I have started looking at implementing shorewall as a bridge and had a few minor questions. First off if I want to define hosts in the hosts file would it be #ZONE HOST(S) OPTIONS Trust br0:eth0:xxx.xxx.xxx.xx net br0:eth0 loc br0:eth1 #LAST LINE -- ADD YOUR ENTRIES BEFORE THIS LINE -- DO NOT REMOVE Or like #ZONE HOST(S)

Hello, Is there a simple way to take an input, and convert the decimal integers to binary? In this case, I have a CSV file, and I need to convert the first column of every line to binary. Thanks. -- Jason Thibodeau [[alternative HTML version deleted]]

Hello all, I have a very large file (280k lines) containing three comma separated variables. The first variable is a 0 or 1 depicting a pass or fail. The other two are X and Y coordinates. Is there a good way I can represent this data in a chart/plot form other than using a 3d histogram? If I need to use the histogram, should I base my chart off the example contained in the RGL package? Thanks a

I made an atempt to run snort_inline and shorewall on the same system but I could not get snort to see the packets. Maybe someone with a little more iptables knowledge could tell me what I''m doing wrong or if its possible to have the systems setup so that it places packets that the firewall would allow into QUEUE. After setting up and starting shorewall I then issue the following

Hello all, I have a CSV file, that is 2411 columns wide. There are certain instances in teh file, where null values are located. That is: two commas together, without anything in the middle. In a certain section, the only possible values are NULL, 0,1,and 2. I need to be able to detect these NULL's and be able to have them counted. For example, in a frequency table. How can I accomplish this?

On Mon Jan 22 11:00:59 2024 Mark Foley via samba <samba at lists.samba.org> wrote: > > I have scripts that runs ntlm_auth. Before upgrading my DC to 4.18.9 I would > get text string output from the ntlm_auth command. For example: > > STATUS_NO_SUCH_USER > NT_STATUS_WRONG_PASSWORD > STATUS_OK > > My script(s) look for these strings. > > Now with the new

I''m expermienting with Shorewall for use protecting my servers(about 25 all currently using pub addresses). My pointy-haired-boss is somewhat sceptical about adding a firewall that would be a single point of failier for our services. Does anyone have a good set of documentation that I could use in setting up either an Active/Active or Active/passive setup with two identical shorewall

I'm trying to get MRTG up and running on CentOS, but the displayed http page says that I don't have permission to access /mrtg/ on the server. Here are my commands yum install mrtg vim /etc/httpd/conf.d/mrtg.conf /etc/init.d/httpd restart cfgmaker --global 'WorkDir: /var/www/mrtg' --global 'Options[_]: bits,growright' --output /etc/mrtg/mrtg.cfg public at 10.200.200.1

I have created shell script for MRTG statistics of droped/rejected packets: ftp://slovakia.shorewall.net/mirror/shorewall/mrtg/ http://slovakia.shorewall.net/pub/shorewall/mrtg/ rsync://slovakia.shorewall.net/shorewall/mrtg/ example: http://slovakia.shorewall.net/pub/shorewall/mrtg/example/ It is not based on /var/log/messages (syslog), but iptables counter. A lot of packets are droped/rejected