similar to: multicast NAT

The BBC are currently trialling multicasting the Olympics. This requires multicast and IGMP to be available. As far as I can make out, in 2.0.8 at least, all multicast addresses are filtered out and, to my naive eyes, can''t be re-enabled. Please prove me wrong :-) Dirk -- Please Note: Some Quantum Physics Theories Suggest That When the Consumer Is Not Directly Observing This Message,

I am trying to set up my Shorewall box to forward multicast packets to my local net. I do have some problems with mrouted (see below), but I can join and add routes using smcroute. Multicast works when shorewall is disabled. I got a lot of help from the following. http://lists.shorewall.net/pipermail/shorewall-users/2005-January/016674.html I cannot get the multicast packets to pass the fw when

Hi, all! Can I enable multicasting via shorewall? I have router with Gentoo Linux (one interface to ISP, one with alises - to local network). Shorewall work perfect! But now I need setup Quagga (zebra) for dynamic routing between one more router via another provider. All routers daemons (zebra, ripd, ospf) used multicasting. In my configuration already enabled allowBcast and etc.

I need to send multicast traffic through a GRE tunnel between two Linux routers. The tunnel works for normal IP packets, but I can''t see how to make it work for multicast. Here''s the setup: 10.10.10.0/24 LAN-B--------------RtrB-------------RtrC--------------LAN-C 192.168.2.0/24 192.168.1.0/24 RtrB interfaces: eth0

Hi, my ISP is streaming some local concert using UDP multicasting. I followed the instructions on the site which described how to set VLC in order to view the stream, but it didn''t work. I am behind a Linux router/firewall doing NAT. Using google, I quickly found out that the netfilter/conntrack code doesn''t support NATing multicast traffic. I thought about bridging the internet

I''m just looking for a quick sanity check to make sure what I''m finding is really all necessary here. I''m upgrading a gateway/firewall from Linux 2.4 to 2.6 using Mandrake 10.1. In the old 2.4 kernel I structured my firewall rules around the ipsec0 interface, which I understand isn''t present with Openswan running under 2.6 (no KLIPS). Ok, So as I start to

Hi, I have seen http://www.tinc-vpn.org/pipermail/tinc-devel/2010-October/000473.html and so tried out for myself to see if multicast would work in tinc using routing mode. I'm using tinc 1.0.19. My test involved sending a ping out on 224.1.1.1 (as 224.0.0.0/24 is a special case), and while I could see the traffic reaching the other tinc daemons, it never seemed to go out to the local

running Version 3.6.23-14.el6_6 I'm having slow save times with folders names ~something.. ie. /www/~bin/content.txt. doing this via a windows share.. when I save file it has a moment (few seconds) of hesitation.. then saves. When I do /www/bin/content.txt. the file saves instantly. Is there anywhere I can change a setting to fix this? or is this a bug. I've looked in the logs

Hi all, Does anyone know of a method of sending a raw G711 stream to an address in Asterisk. For example, an application that takes a argument of a phone and a port. The reason? I have found a method to paging on Zultys ZIP2 and ZIP4x4 handsets. Basically it involves sending a stream of RTP data to port 3771 to multicast address 224.0.0.1. Would it need to involve me writing my

Hi Laine What you have suggested sounds eminently reasonable. Thanks for your advice. I'm going to give it a shot and report back. Richard On 11/27/19 1:38 PM, Laine Stump wrote: > On 11/26/19 11:07 PM, Richard Achmatowicz wrote: >> Hello >> >> I have a problem with attaching VMs to a VLAN interface. >> >> Here is my setup: I have several physical hosts

Hi When I start shorewall, the multicast stream is stopped. My config: Windows VLC Client-----eth0:192.168.254.1/24--fw---eth1:191.168.254.254/16-------------------------Linux VLC Streaming server 192.168.254/24 lan wan (but it''s really a internal lan !) 191.168.1.21/16 on the FW/shorewall route add -net 224.0.0.0 netmask

On 31.07.2014 17:23, Dennis Jacobfeuerborn wrote: > On 31.07.2014 15:14, Dennis Jacobfeuerborn wrote: >> Hi, >> today a couple of Hypervisors got restarted due to a power outage. While >> the systems and the VMs on the are running fine multicast traffic >> between the guests is no longer working. >> >> I generate multicast udp packet using iperf in the guest

Hi, I have problem with multicast routing on my network. I tried mrouted and also pimd, but always same problem. When I set mrouted or pimd on one router, everything works fine, but when I start mrouted/pimd on another one, routing die. In moment when I start anorher mrouted/pimd /proc/net/ip_mr_cache is cleaned. My topology: gateway (no mrouted/pimd)

Even more puzzling, I reverted back to the old configuration to confirm what I had seen and found that it works in one direction but not the other: i.e. from 192.168.0.110 to 192.168.0.120, but not the other way around. Must be something with my configuration....which I can follow up on. So, thanks again for your help. Richard On 12/3/19 11:36 AM, Richard Achmatowicz wrote: > Laine >

I have a shorewall 2.0.14 running on a single interface machine (nwww in the log below) that is attempting to be well screwed down. The policy file reads:- #SOURCE DEST POLICY LOG LEVEL LIMIT:BURST fw net DROP info net all DROP info # The FOLLOWING POLICY MUST BE LAST all all

Hi all, We want linux (ubuntu) with 2.6 kernel to act as multicast router and to pass multicast packets between different subnets. And linux machine as router has two network cards having two different subnets assigned onto. We first worked "sysctl -w net.ipv4.ip_forward=1" line on linux shell that made linux to work as unicast router. (like host, the multicast packets were discarded at

I have a Debian 8 64-bit machine set up as a server and apt-got the tinc package. I configured tinc as a bridge and everything seems normal except that the tunnel does not forward multicast traffic. I used tcpdump to examine the br0, eth0 and tap interfaces. I could see multicast packets on both br0 and eth0, but there is no such packet present on the tap interface. I don't quite know why

How do the Multicast routers sniff IGMP/MLD messages from the network? I checked the XORP, pimd etc. Most of them just open a RAW socket with protocol set to IPPROTO_IGMP. But using this the router gets the packets addressed to 224.0.0.1 only. How does it receive IGMPv2 and IGMPv3 membership reports sent by other hosts? Thanks, Sachin

hi all, This is my first message to the group.My name is Anirban Chakraborti and I am with new mexico state university. I have recently built a router using suse linux.I need to turn on IGMP and PIM to allow it do multicasting.How to do that? Secondly I also want to control the rate of the datatransfer from the router''s ethernet interface to the ppp interface. Thanks for the

well, once i figured out what to do it was easy. 1) install freebsd over linux. 2) recompile kernel with: option MROUTING 3) start mrouted 4) go get yourself a cold beer. you deserve it! thanks! -bob CONFIDENTIALITY NOTICE: The information in this electronic mail transmission contains confidential information intended only for the use of the individual or entity named above. If the