similar to: dnat problem

I''m attempting to setup Squid as shown on: http://shorewall.sourceforge.net/Shorewall_Squid_Usage.html#DMZ The firewall is a Bering 1.0 firewall running Shorewall 1.3.11, Red Hat 7.2 on the server in the DMZ. I''m not seeing the requests come in to the server using tcpdump. The server is 192.168.2.1 connecting to eth2 on the firewall, the local traffic I''m trying to

I have problem getting answer on http request from all my local subnets but not from local subnet. Ping and requests on ports 21 22 23 25 110 works fine. I logged port 80 in rules files and I got accept entry same for local subnet and other subnets. Local subnet is 192.168.6 Dec 29 09:52:40 zinfsrv2 kernel: Shorewall:loc2fw:ACCEPT:IN=eth0 OUT= MAC=00:09:6b:07:ca:cc:00:10:b5:fa:bd:71:08:00

Hi, Trying to figure out why I cannot get access to dell.com Their site is up because I can browse using a different firewall. Trying to find out where the logs are located and what log files it would write to if it were to deny browsing to a website. I can see the [UNREPLIED] when using the shorewall status. Was hoping to know what logfile it is writing it to. Thanks in advance, Elmer

sorry, i''m confuse where to post my problem.. i was post to shorewall-users, but must read to support.html this''s my problem ----------- i have squid running on DMZ zone and my network using ProxyARP on eth1 and eth2 mylinuxbox slackware 9.2 my network can access to internet normal, but can''t redirect to squid server from firewall. sometimes my network can connect

Currently I have shorewal 2.2 installed om my debian 2.6.8 kernel. The firewall machine can access the internet via a ethernet modem fine. The firewall can ping the local network. The local network can ping the firewall server, see the samba files. Howeven teh local network cannot access the internet through the firewall Any suggestions? Rob van Overbruggen Settings and stats: Server: Eth1 :

Hi, I get frequent logfile entries from Shorewall similar to the following: Nov 25 11:22:51 10.0.0.248 kernel: Shorewall:net2mill:DROP:IN=eth2 OUT=eth0 SRC=202.96.117.50 DST=10.0.0.10 LEN=56 TOS=0x00 PREC=0x00 TTL=241 ID=0 PROTO=ICMP TYPE=11 CODE=0 [SRC=10.0.0.10 DST=202.101.167.133 LEN=48 TOS=0x00 PREC=0x00 TTL=1 ID=13591 DF PROTO=TCP INCOMPLETE [8 bytes] ] Could someone explain what the

Hi Tom Here is the output of shorewall status Thanks Lars [H[2JShorewall-2.0.13 Status at - Thu Dec 30 21:43:44 CET 2004 Counters reset Thu Dec 30 15:38:17 CET 2004 Chain INPUT (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 38383 11M ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 0 0 DROP !icmp --

I wonder if someone can tell me what these ''unknown'' remarks mean in my status file. They are only in the last portion of the file and are listed below. If they mean nothing, I will rest easy. But if not it means I need to fix something. Your thoughts would be appreciated. ---------------- udp 17 92 src=24.224.173.220 dst=24.222.0.75 sport=1027 dport=53 src=24.222.0.75

Dear List! I use a shorewall 2.0.8 on a Debian sarge system. I use a DSL connection to the Internet (ppp0 - eth1 to the modem) and a bridge to the local lan. The bridged config i''ve made with bridge.html from the shorewall site. The Bridge is between local net and a openvpn tap device. This works. I ccan make tunnels, and a can make a lot of things through the firewall. I can get a list

Hi all, I''m new to shorewall and have been struggling with several problems for several days now. Most of them are solved, but one still persists. The firewall is running on my server under Debian Sarge (Kernel 2.6) I''ve got three network interfaces: ppp0 (DSL Internet) eth1 (lan) ath0 (wlan) eth1 and ath0 are bridged together to br0. The problem is, that Samba (also running

I have an ADSL router, a linux box with two NICS connected to the router and another PC connected to the router. I installed shorewall using the two interface method. I can ping and see the webserver on the linux box from the local network, but not from the internet. Sys info as follows: [root@wilma root]# shorewall version 1.4.6b [root@wilma root]# ip addr show 1: lo: <LOOPBACK,UP> mtu

I apologize for the first message. :) --------------------------------------- I have an FTP server running in the DMZ section of my home network. It uses port 23000 for connection and ports 19990 to 19994 for data transfer. I have setup the following rule for outside people to connect to it: DNAT net dmz:192.168.2.2 tcp 23000 I''m at work right now and I can''t use

---------- Original Message ---------------------------------- From: "Jim Van Eeckhoutte" <jim@vaneeckhoutte.com> Reply-To: <jim@vaneeckhoutte.com> Date: Mon, 8 Jul 2002 15:27:14 -0700 this is shorewall status output: tcp 6 431899 ESTABLISHED src=192.168.20.5 dst=64.4.12.45 sport=2185 dport=1863 src=64.4.12.45 dst=63.25.123.58 sport=1863 dport=2185 [ASSURED] use=1

(Sorry, my previous post was sent in HTML format) I am having a hell of a time with shorewall... I have a Dlink DCM202 Cable modem with the Ethernet connected directly to eth0 on the linux box. Then I have a second nic on the linux box connected to a hub for the internal network. I am trying to allow traffic from the internet connect to my FTP and WEB servers on my Winbloze box on the lan.

I have what strikes me as an odd problem with shorewall. Let me describe my setup. My desktop (alfred) is connected to the network through an ADSL modem. I am running rp-pppoe, and this works perfectly. I have a small home network, with two LANs; an Ethernet LAN (including a machine running Windows XP), and a WiFi LAN, including the laptop (william) I am using now. All the computers except for

Typically (or at least somewhat occasionally) after a reboot of my shorewall[-lite] machine I find that I end up with conntrack table entries for unNATted connections such as: # conntrack -L -p udp --dport 5060 -d 99.232.11.14 udp 17 59 src=10.75.22.8 dst=99.232.11.14 sport=5060 dport=5060 packets=5472 bytes=3031488 [UNREPLIED] src=99.232.11.14 dst=10.75.22.8 sport=5060 dport=5060 packets=0

Hello! I am using shorewall shorewall-2.0.11-1 on fedora core2 (iptables-1.2.9-95.7). My box has 2 physical nic´s plus one virt. ipsec interface for a freeswan-vpn connection. A few days ago, portsentry spit out a lot of connections from windows clients (port 135, 445). Ooops. I review my shorewall settings but could not find a mistake. So I took a win-client and established a second

Hello All, I have a question about setting up the shorewall firewall for squid, I followed the instructions on "Using Shorewall with Squid" --> "Squid Running in the DMZ" section. For some reason I am unable to get the program to work. I am able to have the squid work properly by using squidclient program, but once I setup the firewall to use the redirect I am unable to

the establishment of an openvpn link sometimes fails. I tracked it down to network traffic with wrong Sourceport in the answer packet (should be 1300 not 1024): 2 1.119309000 aaa.185.165 bbb.162.192 UDP 58 Source port: 1300 Destination port: 1300 3 1.119446000 bbb.162.192 aaa.185.165 UDP 66 Source port: 1024 Destination port: 1300 and a collateral entry in the connection tracking table

I do not understand some colums in the output to ''shorewall show connections'' /root> shorewall show connections Shorewall-2.0.2f Connections at firewall - Mon Jan 3 13:12:52 PST 2005 .. tcp 6 353296 ESTABLISHED src=112.129.244.121 dst=224.81.133.205 sport=3647 dport=443 src=224.81.133.205 dst=112.129.244.121 sport=443 dport=3647 [ASSURED] use=1 I would like to know