similar to: Config with ADSL

Hello, Is there a sample-configuration for users who which have "PPTP Client running on your Firewall with PPTP Server in an ADSL Modem" Where can i find this file as described in the document? "If you have this type of setup, you need to modify the sample configuration that you downloaded as described in this section." Thanks, borsti

I have installed latest Shorewall 1.46b on my Debian Woody ( debian-kernel 2.4.21 + iptables 1.28 ) I have an Ethernet ADSL Modem that connect using " PPTP " My ADSL line has dynamic IP. The modem is on eth0 The modem ip is: 192.168.1.1 eth0 ip is: 192.168.1.2 I''d like to make that pc as gateway for my local network of 7 pc too. The second NIC card eth1 has

Hi Tom, I nearly completed the test and installation related to http://www.shorewall.net/PPTP.htm. However, there is no serious problem when it is operated as it is in the general companies, but there is Client Program for MS-Window that is operated only by Public IP. So I am very concerned about it. I would like to use Internet through Gateway in (B) as local computers in (A) receive Public

Under Linux, i can configure my DSL connection with pppoeconf (debian), without configure my Ethernet interface (eth0), just load kernel module fo ethernet interface, launch pppoeconf here is it. Another way is to configure the DSL interface (eth0 -> ALCATEL Speed Touch Home) with IP:10.0.0.1 so i can telnet or access with an web explorer the modem on 10.0.0.138. After i launch pppoeconf and

Hi ! Recently i switched my internet provider, to get more speed but another braindead setup regarding public ip addresses. I now have 4 PPTP Tunnel available, of which i''m using one as the gateway ip doing masquerading to other machines in my local lan, excluding three other machines, which i would like to use 1:1 nat to get them a direct access to one of the pptp tunnels. I was

Hi There, We currently using iproute2 for load balancing. However we need more upload speed as we load balance over 3 dsl lines. I''ve been looking for a way to combine the upload speed to more faster. Found a site called www.upstreaminter.net where these guys bond the adsl channels to improve uploads, Since downloading is problem as its need to know the ip address of the downloader they

I'm using shorewall 3.0.4 with ubuntu dapper. I've compiled the kernel with the option CONFIG_IP_ROUTE_MULTIPATH_CACHED=n. I had a trouble with, pptp connection, I'm trying to connect a using microsoft vpn a vpn server out of my lan, and don't work. My files <providers> ADSL1 1 1 main eth1.600 10.190.1.1 track,balance eth0 ADSL1 2 2 main eth1.601 10.190.2.1

Hello all, I had setup shorewall before succesfully with a normal LAN to internet connection. Now I''m connected to the internet via VPN and I got problems with configuring Shorewall. Any help is appreciated. This is my setup: - Gentoo Linux laptop (kernel gentoo-dev-sources-2.6.8.1) with Shorewall 2.0.4 (setup for Standalone one interface) and iptables 1.2.11 - VPN client is

I''ve got what I think is a fairly simple home network configuration with one Linux box functioning as the firewall, VPN server, DHCP server and file/print server. I am having trouble configuring both a VPN server (PopTop) and the firewall rules for a W2K PPTP VPN client. The VPN server runs on the firewall machine and the VPN client runs on a W2K machine behind the firewall. The VPN

Hi, I successfully connected quite a few servers with their associated networks using Suse 9.1/9.2 (Kernel 2.6.x) and IPSEC tunnels. But now I have to add another server that has a ADSL connection to the internet, that means it has a dynamic IP address which is likely to change every few hours, since the provider disconnects from time to time. I found a way to restart the IPSEC connection when

Hi, I currently connect to my ISP via my adsl modem in bridge mode and PPPoE. I am due to put a second PPPoE ISP onto my firewall box which will give me ppp0 (general) and ppp1 (static leased line). The static leased line will run a number of services on its static IP and it is therefore imperative to make sure rules defined for the static line are assigned to the correct interface. I need this to

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I have a situation where some Poptop/PPTP sessions (only with FC5/Shorewall to FC5/Shorewall firewall in between) cause the following to appear in the state table (shorewall show connections). unknown 47 420 src=XX.234.79.183 dst=XX.234.137.226 packets=2 bytes=130 [UNREPLIED] src=XX.234.137.226 dst=XX.234.79.183 packets=0 bytes=0 mark=0 use=1

Hi guys, I''m trying to setup an IPIP tunnel between a Cisco router and a firewall running Debian GNU/Linux Sarge with Shorewall 2.0.13. I''ve read and implemented the http://shorewall.net/IPIP.htm document, but I don''t understand why there should be at the same time a "tunnel" and a "tunnels" script. Shorewall still refuses to let the

Hi, I have a very simple server setup, using shorewall as my firewall. I have a line like this at the top of my rules file to allow ssh connections, but limited to 3 connection per minute with a burst rate of 3: SSH/ACCEPT net $FW - - - - 3/min:3 - Now when I have that in place, and from a remote machine run scp server:/some/file ., I find

Does anyone have any information or recommendations for ADSL PCI Cards for Linux boxes? E.g. which ones are supported? How much are they? etc. Dirk -- Please Note: Some Quantum Physics Theories Suggest That When the Consumer Is Not Directly Observing This Product, It May Cease to Exist or Will Exist Only in a Vague and Undetermined State.

Hi, Before I go any further, I''m no networking expert, and the sheer volume of documentation on the Shorewall website makes my brain hurt.. Some time ago I moved from an area with cable internet to an ADSL only area. While on cable, I''d set up an old P3 box running Gentoo as a firewall/gateway/file server, running shorewall (currently v2.2.3) and dnsmasq. I''d

Hello every one, first time poster, four month shorewaller ;) As the subject states, I''ve been experienced the infamous trouble described in the next excerpt from shorewall.conf # MSS CLAMPING # # Set this variable to "Yes" or "yes" if you want the TCP "Clamp MSS to PMTU" # option. This option is most commonly required when your internet # interface is some

Good Morning Everyone, I have a server that runs Shorewall/Samba/PPTP (Poptop). When we try to connect to the PPTP server from outside of the company, the Windows XP pro client can establish the connection. We can then ping the server and the clients behind the server without any problem, but the issue becomes that we cannot map to any of the shares on the samba server or to any client for that

how can I check whether packets are being marked as per my tcrules file? 4 0.0.0.0/0 202.37.230.93 udp 500 4 fw 0.0.0.0/0 udp 500 also can someone confirm what ports are needed to be opened for ipsec? 1701,1723,47,500 ??? P.

Hi all .... I Have installed Bering LRP on Many sites and I am very pleased with the capabilites of shorewall. Howerver I came across a prob that I am unaware ot its solution. Using shorewall 2.0.2f Kernel 2.4.24 On one Site LRP box serves internet outgoing connections through ( static IP ) a DSL line AND an incoming dial-in PPP conection. My shorewall configuration Is based upon the fact