similar to: Is Load Balanced VPN possible?

There was a lengthy power failure here in Shoreline this morning and my firewall did not come back up when power was restored. The firewall is now up and service to the server has been restored. -Tom -- Tom Eastep \ Nothing is foolproof to a sufficiently talented fool Shoreline, \ http://shorewall.net Washington USA \ teastep@shorewall.net PGP Public Key \

Hello All, Figured I'd ask this. I have an asterisk running with some X100P clones. The system runs fine. My question is, the lines are tied into a panasonic dbs analog extension. When you call through, all goes well except that the call does not know it is connected. This causes problems if lets say, I want to do a 3 way conference, since my cisco 7960 does not see the call as connected,

Hi, Someone released a succefull interconnection in H323 with WTL equipement ? I'm trying to do that with an IPNx. But get dead air. With chan_oh323 it's fine, all works. With chan_h323 => dead air. The configuration is GW to GW. This is my configuration from h323.conf: [general] port=1720 bindaddr=my.ipaddr dtmfmode=rfc2833

Hello List, I know 4.9 is ancient history, but unfortunately we have several thousand sites installed. We are in the process of moving to 6.1 when it is released. Right now I have an immediate problem where we are going to install two system at a HQ site. Each of the 2 systems will have two gre/vpn/ospf tunnels to a 100 remote sites in the field. The broadband will be a T3 with failover to

Hi, > Can you manually do on the xen interfaces what the scripts would? How about > doing it on some other interface configured in a similar way? Toying with the vif-route script, I might have found a workaround for this issue. If I disable the ifconfig and ip route commands from vif-route script, and bring up vif interface by hand later on, everything seems to work. In other works,

Hi, i have a problems with windows clients when they try to change the password, windows respond with "Please enter valid character..." but the pass get changed. i have this in smb.conf passwd chat = *Enter\snew\sUNIX\spassword:* %n\n *Retype\snew\sUNIX\spassword:* %n\n . when i change that to: passwd chat = *New*UNIX*password* %n *Re*ype*new*UNIX*password* %n

Hello All, Does anyone happen to be running Quagga on CentOS 5 with SELinux in enforcing mode? Have you had to create SELinux policies or did it "just work" out of the box? (I'll get around to building this out on CentOS 6 as well.) I'm simply trying to write my config (for the zebra daemon) and it can't be written... Looks like this bug from Fedora 8 in 2008 [0] remains

Hello, Here is my network: ------------------ ------------- ----------- Linux box ----------- GRE --------- Cisco ---------- ------------------ ------------- What I wan to accomplish. I want ripv2 to go across (both ways) through the GRE tunnel. No packets are being passed thought the GRE

First of all, My apologies for this maybe slight OT post, but I have so much confidence and read so much good replies on this list, that I am still asking my question. I''m looking for a linux distribution to use on our school''s homemade routers. The routers are small miniITX based systems with 2 network interfaces. I added a 4 port D-Link network card in some cases, when I

Hi Nitin, First of all, you can verify that ntpd is responding on ingress with netcat : nc -u ingress 123 (udp connection on port 123) also try a netstat -an on ingress to be sure that the port 123 is in listen state... I recently install ntpdate, and it has worked as a client and a local ntp server immediatly. Good Luck, Yannick / Annecy in France -----Message d''origine----- De :

Hi list, I have a problem I thought was simple first, but now I''m stuck. In a nutshell, it''s about redundant uplinks at an outside location. Crude ASCII-Art follows: Internet | | +------------+ | cisco with | | uplinks | +------------+ | | ATM interface +----------+ ... | alvarion | | | wireless

Hi, I have recently updated one of my systems from CentOs 6.4 to CentOS 6.5. This systems is used as a RIPv2 routing server with quagga which is the termination point of some GRE tunnels. While running CentOS 6.4 I see the multicast packages arriving at the eth0 and the GRE tunnel interface. While running under CentOs 6.5 I can see the multicast packages arriving at the eth0 but not on the GRE

Hi, With kernel 2.4 I was able to use equalize to send our outgoing packets to two different routers (our isp supports this setup), like this: ip route add default src ip.a.dd.rr equalize nexthop via <router1> weight 1 nexthop via <router2> weight 1 The two routes were used equally on a per packet basis, not per flow or per cached route, but per packet, each line has 800k upload

Package: xen-hypervisor-3.0.3-1-i386-pae Version: 3.0.3-0-2 Severity: normal If quagga is running, and I start & stop a domain, the VIF interface doesn't go down properly (in addition to other problems). Here's what I do: 1. Boot the computer. By default, quagga is running (zebra + ospfd). 2. xm create test7.cfg, wait until the domU starts. 3. xm shutdown test7, wait until the domU

I have an office setup with shorewall and when there''s bandwidth problems, I''d like to know who''s hogging my bandwidth and how (port). What would be the best approach to have shorewall show me something like: IP | Port | Bytes In | Bytes Out I have 20 PCs connected via DHCP. I looked at the documentation and thought that accounting may be close, but accounting

Hello, Can anyone tell me why the maximum number of members in a multicast group is set at 20? Are there issues with increasing this number? Any information would be greatly appreciated. Thanks, Steve Clark -- "They that give up essential liberty to obtain temporary safety, deserve neither liberty nor safety." (Ben Franklin) "The course of history shows that as a

Hi, In XenServer5.6 FP1 beta, I have switched default bridge to open vswitch, I wonder how to use "xe tunnel-create" to create a GRE tunnel. my commands: xe tunnel-create pif-uuid=eth0_uuid network-uuid=network_created_by_xe_network_create then I got an uuid which is "access-PIF" of output from "xe tunnel-list". what should I do next? how to set remote_ip

Hello everyone, I have a problem regarding gre tunneling, I have two linux box both of them has a private network and the linux A is connected to the internet via wireless radio and the other linux B is connected to the internet via lease line. Here is the setup of my two linux box Linux A eth0 = 203.189.x.1 (internet) eth1 = 192.168.1.1 (going to hub private network) Linux B eth0 = 205.198.x.1

https://bugzilla.netfilter.org/bugzilla/show_bug.cgi?id=512 ------- Additional Comments From kaber@trash.net 2006-09-18 07:36 MET ------- There are still some problems with the PPtP helper, I'm currently trying to fix these. Can you attach a tcpdump of a failed attempt please? -- Configure bugmail: https://bugzilla.netfilter.org/bugzilla/userprefs.cgi?tab=email ------- You are

Hey guys I''ve been beating my head on this for a few hours. Maybe it is just a stupid configuration error you can point me at. First here is a small diagram of what I am trying to configure: http://6bit.com/img/netdiag.png Currently I only have Shorewall running on the host on the right of the diagram until I can get this working then I''ll add it to the other host as well.