similar to: encoding -> decoding doesnt work

hy, recording and playback without speex is working perfectly Lp, Tim +--------------------------+ | email: rico at gama.us | | www: http://gama.us | |--------------------------| | tel: 00386 31 457 627 | +--------------------------+ 2009/9/2 Tim Rijavec <rico at gama.us> > hy, > > here is my speex encoder/decoder .. the sampleRate i use is 16000 and >

hy, recording and playback is working perfectly without speex. i have try to set samplerat from 6000 to 441000 and quality from 1 to 10 sam with complexy, but the best i can get is with 16000 samplerate, 5quality and 3complexy .. but still, the voice that came out is annoying, artificial, robot ,... Lp, Tim +--------------------------+ | email: rico at gama.us | | www: http://gama.us

hy, here is my speex encoder/decoder .. the sampleRate i use is 16000 and quality,complexity are at 5. can someone take a look in to the code and see if there is something that is making that robot voice here is a link to colored and numbered code, same as below http://barvanjekode.gama.us/temp/1257361243.html thanx. code ----------------------- #include "codec.h"

Hi Tom, Thanks for your reply, I'm having a few difficulty's following you advise. You mention that I should be calling 'speex_encoder_int' & 'speex_decoder_int', I'm having problems finding these functions in the speex header. I am currenlty calling speex_encoder_init & speex_decoder_init in my test code, I have repeated the relevent bits of the example

In short try calling speex_encode_int and speex_decode_int. The calls to speex_encode and speex_decode expects the data to be a floating point values. The data is passed by pointer and the compiler does not do the conversion. This is why you are getting the segfault on decode as the short is 16-bits and a standard float is 32-bits. Tom -----Original Message----- From:

Hi, in my application i quite often (not allways) get those two warning: "Invalid mode encountered: corrupted stream?" "Invalid wideband mode encountered: corrupted stream?" The stream is not corrupted but i wish to know what those warning mean to correct my code. My encode and decode routines are those (libspeex 1.1.4): SpeexBits enc_bits, dec_bits; void *enc_state,

Hi All, I'm very new to speex and in fact handling audio at all, it seems I have run in to a problem I seem unable to fix. I'm trying to take audio from a microphone using alsa, then encode it as speex and save to disk. I have been wondering if it has something to do with endian type, but speexenc and speexdec works fine. Currently I have the following setup: Platform:

Hi, I read in the documentation something about how to realize packing more than one encoded frame into a packet. Before I read this, I always encoded every frame seperate and packet them as following together: [encoded length][encoded frame][encoded length][encoded frame]... But if I understood the docu correct, it should be easier: I call speex_encode_int() for every frame until the whole

Hello! I am downloaded last version of speex library and did compile DLL. But I am have not good sound : Please see my code (Delphi) and say me please WHat I am do not right. Or please send me correct compiled DLL and example of correct using SPEEX_MODEID_WB and SPEEX_MODEID_UWB , denoise, and other effects. How I can set MONO mode in decode? My Code: smpRt:=32000; n:=10; encbits:

I have read the speex manual, looked at the example code, but for some reason the first encoded byte does not have the wideband bit set and the mode bits are also wrong even though I am encoding in wideband mode. I am sure that I am doing something wrong, but I can't figure out what it is. I have included my code below.... I would expect that the MSB of the first encoded byte is 1

Anton A. Shpakovsky <saa <at> tomsksoft.com> writes: > > As for me - speex_echo_cancellation is a better choise. Try using it in > capture thread instead > of those speex_echo_capture and speex_echo_playback functions. > > And please, describe your problem in details. Cause the fact that you > "didn get echo cancellation" > doesn't mean you are

Well, I'm not a professional in AEC theory, but what I've mentioned is: speex_echo_state_init(20, 320*10) - frame size should correspond to 20ms. At your sampling rate (16000hz) is should be 16K*0.02 = 320. The same I can notice about echo tail. 100ms: 16000*0.3 = 4800, not 3200 as you has. But that's not crucial I think. Just wanna you get the point. "Internally,

On 12/13/07, Jean-Marc Valin <jean-marc.valin@usherbrooke.ca> wrote: > > I am a newbie here and just started using speex in our lab. > > During compiling my voice application with windows-compiled version provided > > today, I am getting "unresolved external symbol _speex_wb_mode". > > I am probably missing some setting with VS6.0 linker... (I am a bit new

Hi, I'm trying to use speex codec in iax client to connect to asterisk (all last version) It seems that when I use speex_encoder_init(speex_lib_get_mode(SPEEX_MODEID_WB)) Instead of speex_encoder_init(speex_lib_get_mode(SPEEX_MODEID_NB)) Asterisk try to downscale the codec to ulaw. Please advice, ofer -------------- next part -------------- An HTML attachment was scrubbed... URL: