similar to: How to use the speex AEC

Thanks for alerting me to the new changes. I just tried the latest code from SVN, but unfortunately I still have just about the same results. The estimated echo that gets subtracted from the actual echo is such a small signal that it doesn't really result in any noticeable echo attenuation. I currently have my filter size set to 2 seconds even though the echo in my microphone file is only

I ran some further tests on mdf and here are the results: 1. reduced tail length to 100ms, aligned mic and speaker signals to within 10ms - almost no echo attenuation 2. aligned mic and speaker signals to within 5 samples - still almost no echo attenuation 3. ran testecho using the same file for mic and speaker - very good echo cancellation (of course this is expected, but I needed to do a sanity

Le vendredi 11 novembre 2005 ? 01:21 -0800, Duane Storey a ?crit : > This is a very real problem though.. I've encountered many sound cards that > use different clocks for input and output (even on the same card!) Also, if > you open up a sound device on windows at 8kHz, the microphone is often > around 8100Hz, while the output is 8000Hz.. I'm not sure if there's a bug >

I'm pretty much sure of it. When I test inverting the inputs, my output is pretty much the same as my speaker signal. Whereas the way that I normally test the output is my mic signal with very little attenuation. If you are interested I can send my test files; they are about 94KB each. -Jason --- Jean-Marc Valin <jean-marc.valin@usherbrooke.ca> wrote: > Are you sure you're

I've tried some further debugging to see what mdf is actually doing. Instead of sending: tmp_out = (float)ref[i] - st->y[i+st->frame_size] to the output, I just sent st->y[i+st->frame_size] to see what was being subtracted from the microphone input. When I open this in Audacity, I see a very small signal at about -40dBm. The actual echo in my sample has a power closer to -20dBm.

Greetings everyone, I was about to compare AEC performance between 1.1.12 and 1.2beta1 when I noticed something. If I configure (and compile) speex-1.1.12 with ./configure --enable-shared=no --enable-static=yes it compiles and works as expected: I can run a mic and speaker signal through testecho, it runs in a reasonable amount of time (about 23 secs for 3 minutes of audio) and I get back

On Mon, Aug 11, 2008 at 12:34 PM, Jean-Marc Valin < jean-marc.valin at usherbrooke.ca> wrote: > OK, here's what happens. There is indeed a small difference between > beta3 and rc1, but the fundamental problem isn't there. I've attached > plots of the speaker signal (blue) alongside the mic signal (green). You > can see the delay is in the order of 1000 samples.

I'll try to make some shorter samples later, but for now here are the ones I have tried with: http://www.surfnonstop.com/~bandit/speex/1.2beta1_AEC_garble/ The original recordings are in mic.raw and spk.raw. Jean-Marc Valin wrote: > You may have triggered an instability problem. Can you upload your files > somewhere so I can have a look at them? > > Jean-Marc > > Andras

speex-devDear Jean-Marc Valin I got some problems with evaluating the AEC module of speex. I wrote a test main function and compiled it with the speex lib in VC6.0, it initialized the AEC state and called the AEC main function in the same way as what was done in testecho.c. The near-end input wave file was a simple delaying and adding version of the far-end input wave, eg. y(n) =

To everyone on the list: do *NOT* attempt to do echo cancellation with signals sampled using different clocks. This will *NOT* work. Just a 0.1% difference between the two sampling rates (it's sometimes worse than that) means that the impulse response drifts by 8 samples every second. There's just no way to efficiently track this. Or at least no way that doesn't involve something 100x

Had a try. The reason why a simple delay is not that good is mainly due to the initialization of the filter parameter that still takes a few seconds (if they are perfectly in sync, you sort of get lucky). Otherwise, you real recording seems to have something odd in it. Are you sampling from a different card then the one that's playing the sound? or maybe the mic (or something else) in the room

Hello? I am a new user of speex.I am currently working on speex frames and I have some questions. I am using narrowband and long tail length, and it works very well with speex test DEMO. But it is very difficult to have speaker input in perfect sync with mic input. Speex does not work at all. Any suggestion? Regards? -------------- next part -------------- An HTML attachment was scrubbed...

On Sat, Aug 9, 2008 at 12:59 PM, Jean-Marc Valin < jean-marc.valin at usherbrooke.ca> wrote: > Hi Benny, > > Can you send me your pair of testecho input files that work well with > beta3 and not with rc1? I'll have a look. > > Thanks for the help. The files are on their way now, the upload will take few more minutes to complete. In the mean time let me explain more

Dear all: I need the help desparately. The code is attached below. If you guys don't mind take a look at the code below and see how to fit speex's AEC into it. Help me look at the #defines, and give me some suggestions on the AEC parameters, I totally have no idea about them. Feel free to do anything with the code, if it is by any chance valuable. Any ideas or suggestions or sharing

Hi: By 'no success', I mean result gets worse in terms that, there comes in a shrill noise with high gain and also *no* attenuation of the echo. I am trying to validate the DC offset part. But can you please feed some light on how does the DC offset matter for AEC. As I have already mentioned, I tried adding silence (from 2 ms to 10 ms) in the start of the reference signal. This is for

Hi, I couldn't find a discussion that specifically addresses this, so here it is. I'm using Speex AEC in my mobile VoIP application to cancel speaker echo. The used version is 1.2rc1 from the website, and I'm compiling with fixed-point. On most occasions, the AEC works very well and cancels most of the echo (combined with the preprocessor). On some devices, where the microphone signal

This kind of behaviour is odd. One of the reason could be the fact that you're using a really long impulse response. Try syncing your signals and making the tail length more in the order of 100 ms to 300 ms. Jean-Marc Le dimanche 06 novembre 2005 ? 21:25 -0800, Jason Harper a ?crit : > Thanks for alerting me to the new changes. I just > tried the latest code from SVN, but

Hi Jean-Marc, I tried with both testecho and my test program, and for some reason it just doesn't cancel any echoes with the 1.2-rc1. The testecho from beta3 binaries works fine, and also if I replaced mdf.c in 1.2-rc1 with mdf.c from beta3 and use my test program, it will work again. This happens for both 8KHz and 16KHz. Any ideas? I could upload the test samples and results if needed.

Are you sure you're not just inverting the two inputs? Jean-Marc On Wed, 2005-11-09 at 22:16 -0800, Jason Harper wrote: > I ran some further tests on mdf and here are the > results: > 1. reduced tail length to 100ms, aligned mic and > speaker signals to within 10ms - almost no echo > attenuation > 2. aligned mic and speaker signals to within 5 samples > - still almost

I've recently made changes to the AEC. Please try the code in SVN and see if it works better. Jean-Marc Le jeudi 03 novembre 2005 ? 22:36 -0800, Jason Harper a ?crit : > I've tried some further debugging to see what mdf is > actually doing. Instead of sending: > tmp_out = (float)ref[i] - st->y[i+st->frame_size] > to the output, I just sent >